(b) Draw Axial Force Diagram of the following elastic steel beam (Figure 9). Determine the relative displacement of point D from point A for the elastic steel bar of variable cross sections shown in Figure 9 caused by the application of concentrated forces. Areas AAB = 3000 mm², ABc = 1500 mm², Ace = 750 mm?. Modulus of %3D %3D %3D Elasticity, E = 200 GPa. 700 KN 500 KN 300 KN 100 KN 2000 mm 2000 mm 300 mm 300 mm. D A B C E Figure 9

(b) Draw Axial Force Diagram of the following elastic steel beam (Figure 9). Determine the relative displacement of point D from point A for the elastic steel bar of variable cross sections shown in Figure 9 caused by the application of concentrated forces. Areas AAB = 3000 mm², ABc = 1500 mm², Ace = 750 mm?. Modulus of %3D %3D %3D Elasticity, E = 200 GPa. 700 KN 500 KN 300 KN 100 KN 2000 mm 2000 mm 300 mm 300 mm. D A B C E Figure 9

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(a) Compute the horizontal displacement of joint B produced by the 240-kN load in Figure P8.10. For all bars, area = 2400 mm2 and E = 200 GPa. (b) Assuming that no load acts, determine the horizontal displacement of joint B if support A moves 20 mm to the right and 30 mm down and support E moves downward 36 mm.
As shown in the figure, aluminum rod AB and steel rod BC, hinged to rigid supports, are pinned together at B to carry a vertical load P = 6000 lb. If aluminum rod has a cross-sectional area of 0.60 in.² and E = 10 × 103and steel rod has 0.50 in.² and E = 29 × 106 each rod and the horizontal and vertical displacements of point B. Assume α = 60° and θ = 30°. ksi, psi, compute the elongation of
The beam AB, shown in Figure 1a, with length L = 4.5 m is subjected to a uniform distributed load w = 13 kN/m and a concentrated moment M = 18 kN.m applied at point B. The beam has a rectangular cross-section with height h = 183 mm, width b = 98 mm, and constant thickness t = 12.5 mm as shown in Figure 1b. Take E = 200 GPa. 1. Determine the moment of inertia of the cross section .2. Determine the slope at point B
Consider a 175-mm-long segment of a simply supported beam. The internal bending moments on the left and right sides of the segment are 75 kN-m and 80 kN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume b1 = 120 mm, b2 = 50 mm, b3 = 210 mm, d1 = 75 mm, d2 = 175 mm, d3 = 75 mm. Determine the maximum horizontal shear stress in this segment of the beam.
There is a beam subject to a uniform force w as shown in the figure below. The E of the entire section is 200 GPa and I is 60x10^6 mm^4. (a) Calculate the reaction force at point c and the vertical displacement at point B (b) If the support point C sinks downward by 0.1m for some reason, calculate the reaction force at point C and the vertical displacement of point B.
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
Using the following values for the figure: W = 18.5 kN/m x = 1.22 m Determine the magnitude of the absolute maximum internal shear force. Determine the magnitude of the internal moment in the beam at x = 3m.
Consider a 155-mm-long segment of a simply supported beam. The internal bending moments on the left and right sides of the segment are 75 kN-m and 79 kN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume b1 = 135 mm, b2= 50 mm, b3= 205 mm, d1= 65 mm, d2= 180 mm, dz= 65 mm. Determine the maximum horizontal shear stress in this segment of the beam.
The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P = 400 kN and P = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,100 mm and Acr = 9,280 mm. The distances between various points on the bars are shown in the figure. Determine the vertical displacements & and dp of points A and D, respectively.
Vertical Forces P & F in the figure produces a resultant of 500KN and a counter clockwise couple C of 250 KN-m. Find the magnitude of force P. a.) 1187.5 KN b.) -1687.5 KN c.) -1187.5 KN d.) None of the Above e.) 1687.5 KN
For the beam shown in figure below, draw the shear and moment diagrams: 1- Due to applied loads (without support settlement) 2- Due to support settlement of 60 mm downward at support B (without loads). Take the stifiness E1 as 12000 kN.m”. sou i The solution is according to Slope deflection method
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15 If there is a settlement of S at the support C, solve the following: 1. Slope at B, in radians 2. Slope at C, in radians 3. Reaction at A, RA in kN 4. Moment at A, MA in kN-m 5. Reaction at D, RD in kN 6. Moment at D, MD in kN-m