(b) For the audio power amplifier shown is Fig. 1b, determine the following:i.The RMS power dissipation in the speaker.The efficiency of the amplifier.ii.24 VdcRbC1620 ΩVin20 mV peakQ15:1ReB = 40Ce4700Fig. 1b Transformer Coupled Audio Amplifier8 Speaker

Given: For the audio amplifier shown below: To find: Determine the following: (i) The RMS power…

(b) For the audio power amplifier shown is Fig. 1b, determine the following: i. The RMS power dissipation in the speaker. The efficiency of the amplifier. 24 Vdc Rb C1 HE Vin 20 mV peak 620 Ω Q1 Re 470 Ω www 5:1 B = 40 Ce 8 Speaker

(b) For the audio power amplifier shown is Fig. 1b, determine the following: i. The RMS power dissipation in the speaker. The efficiency of the amplifier. 24 Vdc Rb C1 HE Vin 20 mV peak 620 Ω Q1 Re 470 Ω www 5:1 B = 40 Ce 8 Speaker

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An example power system has two distinct manufacturing areas, one with harmonic loads, and another with only linear loads. The portion of the system with the harmonic loads draws 75 A rms at 60 Hz, 10 A rms at 300 Hz, and 5 A rms at 420 Hz. The part of the system with only linear loads draws 75 A rms at 60 Hz. (i) What is the total load current (at 60 Hz) if both manufacturing plants are running? Calculate the THD. (ii) What is the total load current (at 60 Hz) if only the manufacturing plant with harmonic loads is running? Calculate the THD.
The figure below shows an RLC electrical network operating on alternating current. A load impedance Z of unknown value has been connected to the output of said network. a) Find the value of the load impedance Z, which is necessary to connect to the output of the given network to obtain the maximum average power transfer.b) Determine the value of the maximum average power transferred to the load found in the previous section.Note, the values of all impedances shown in the circuit are given in Ohms.
The amplitude of the voltage available in the 60-Hz, 230-V power outlet in your home is what? A. 250 V B. 300 V C. 325 V D. 350 V
five infinite-impedance volunteers,calibrated to read rms values,are connected as shown below. let R= 200, L=0.400H,C=6.0 Mf, and V=30.0 v. what's the reading of the voltmeter's V1,V2,V3,V4 and V5 if W= 200 rad/s
It has been desired to install a diesel power station to supply power in a suburban area having the following particulars: (i) 1000 houses with average connected load of 1.5 kW in each house. The demand factor and diversity factor being 0.4 and 2.5 respectively. (ii) 10 factories having overall maximum demand of 90 kW. (iii) 7 tubewells of 7 kW each and operating together in the morning. The diversity factor among above three types of consumers is 1.2. What should be the minimum capacity of power station?
Q.12: Consider the linear transformer in Fig. Q12. Determine the input impedance ??? andthe current from the voltage source.
For the frequency-domain circuit , calculate: 1. a) the rms magnitude of Vo;2. b) the average power dissipated in the 9 Ω resistor;3. c) the percentage of the average power generated by the idealvoltage source that is delivered to the 9 Ω load resistor.
a) You have been employed as an electrical engineer by a power transmission company to design a short transmission line to supply power to a light-industrial load consumer with power system specification as follows, a 3-ph, 60Hz overhead short transmission line with a line-to-line voltage of 23KV at the load end, line impedance of 2.48 ±j6.57Ω/phase, the industry has a cumulative consumption of 9MW with a power factor of 0.85 of lagging as a result of several induction motor on its production lines.As part of the regulations for connections to the grid, you are to provide justifications and values to the Energy Commission of Ghana.(i) What would be value of the voltage between the live conductor and the neutral, between live and live voltages at the industrial premises of the factory?(ii) What load angle would expect the factory to be operating at?
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.
A motor draws 680 W at 156 Vrms 60Hz. The motor is operating at a lagging power factor, with a power factor angle of 45 deg.. Determine the capacitance (in microFarad) required to correct the power factor so that the power factor angle becomes 15 deg, lagging. (Give answer in 2 decimal places. Unit is not required)
In the circuit given below, Ra=Rb=Rc=9 ohm loads are fed with an AC voltage with a fundamental frequency of f=30Hz. The power value drawn from the source was measured as PK=5512.50 watts. Each switching element is triggered to be 120 degrees conduction. Calculate the effective values of the voltage Vab and the current flowing through the S1 switching element Vab_rms=, Ls1_rms?
An industrial load consumes 66 kW at a pf of 0.505 lagging from a 480-V rms line. The transmission line resistance from the power company's transformer to the plant is 0.08 Ω. Let us determine the power that must be supplied by the power company (a) under present conditions and(b) thy if the pf is somehow changed to 0.90 lagging. (It is economically advantageous to have a power factor as close to one as possible.