(b) The construction of Wheatstone Bridge used for measuring temperature is as shown in Figure Q2(b). The Rx is referred to the resistance produce by Resistance Temperature Detector (RTD) during the temperature measurement, in which the value of Rx is change proportionally dependently with the change of the temperature. Meanwhile during the measurement, the potential difference is measured from point D to C. (i) (ii) (iii) Calculate the value of Rx at balance condition. Determine the Vout when Rx equal to 12092 Determine the Rx if Vout equal to 0.5V

(b) The construction of Wheatstone Bridge used for measuring temperature is as shown in Figure Q2(b). The Rx is referred to the resistance produce by Resistance Temperature Detector (RTD) during the temperature measurement, in which the value of Rx is change proportionally dependently with the change of the temperature. Meanwhile during the measurement, the potential difference is measured from point D to C. (i) (ii) (iii) Calculate the value of Rx at balance condition. Determine the Vout when Rx equal to 12092 Determine the Rx if Vout equal to 0.5V

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

Using the graphical method calculate: V1, V2 and V3.Indicate the theoretical basis, analysis of results and conclusions.
The table shows the values for the current, I, in an electric circuit and the resistance, R, of the circuit. Solve; a. Graph the ordered pairs in the given table of values, with values of I along the x-axis and values of R along the y-axis.Connect the eight points with a smooth curve. b. Does current vary directly or inversely as resistance? Use your graph and explain how you arrived at your answer. c. Write an equation of variation for I and R, using one of the ordered pairs in the table to find the constant of variation. Then use your variation equation to verify the other seven ordered pairs in the table.
Complete the table and give the step-by-step solution.
Prove the relationship mathematically between the steps in detail
The weight of the car is 800 Kg The weight of each person is 75 Kg You may assume any missing parameters you need in the design appropriately (e.g., the rolling-resistance-power, air-resistance-power, the DC motor's parameters, ....etc)
The electric current I in a circuit shown in the figure was measured as a function of theresistance R in the circuit. The relationship between I and R is given by? =?? + ?where ? is the emf of the battery in the circuit and r is the internal resistance of the battery. where ? is the emf of the battery in the circuit and r is the internal resistance of the battery.a) Linearise the equation above, and state which variable you would plot on the x-axis andwhich on the y-axis.b) How are ? and r related to the gradient and/or y-intercept of the graph?
following equation applies: V = IR. Outside of the linear range, V*IR, outside of the linear ranges where resistors are broken The resistor has a resistance of 100ohm, and a power rating of 250mW. 1) Sketch the plot (and label) of the i-v relationship for the resistor using only the linear range of the resistor. Determine the range of values for the voltage and current that the resistor operates as a linear element and note these simplified numerical values on the plot.
Subject: CircuitsShow your solution and circuits diagram
Find the equivalent resistance for the infinite network shown in Figure P2.12(a). Because of its form, this network is called a semi-infinite ladder. [Hint: If another section is added to the ladder as shown in Figure P2.12(b), the equivalent resistance is the same. Thus, working from Figure P2.12(b), we can write an expression for Req in terms of Req.Then, we can solve for Req.
Bioelectrical impedance analysis is a commercially available method used to estimate body fat percentage. The device applies a small potential between two parts of the patient's body and measures the current that flows through. With an estimate of the resistance individually of the muscle and fat between the two points, the composition of the tissue can be estimated. Assume that the muscle and fat tissue can be modeled as resistors in parallel. a) If a potential difference of 5 V is applied across the patient's arm, what is the potential drop across the patient's fat? b) If the measured resistance of the patient's arm is 750 Ω and the resistance of fat is 3 times that of muscle, what is the resistance of the muscle?
Virtual Lab: circuits and Kirchoff’s rules Go to: https://phet.colorado.edu/it/simulation/circuit-construction-kit-dc-virtual-labBuild each of the circuits in the figures, with the designed characteristics.For each of the circuits, show the calculations to find the current and the potential difference in eachelement of the circuit.In building the circuit in Figure 1) through the simulator, adjust the small resistance of the battery tozero and put in series a small resistance as required from the design.For instance, for E1 you will need abattery with V = 6V and you will need to put in series a small resistance of 0.5 Ω to simulate the smallresistance in a battery.Figure 1)Figure 2)
To extend the useful range of a voltmeter, an additional resistor, Rseries, is placed in series with the voltmeter as shown in the figure. If the internal resistance of the voltmeter is Ri,V, determine the resistance that the added series resistor has to have to extend the useful range of the voltmeter by a factor N. Then, calculate the resistance the series resistor must have to allow a voltmeter with an internal resistance of 1.00 MΩ and a maximum range of 1.00 V to measure potential differences up to 100. V. What fraction of the total 100.-V potential drop occurs across the voltmeter, and what fraction of that drop occurs across the added series resistor?