B- the instrument readings obtained from open and short-circuit tests on 10kVA, 450/120 50Hz transformer are: O.C. test: V₁ = 120V; I₁=4.2A; W₁ = 80W; W₁ and I₁ were read on the low-voltage side. S.C. test: V₁-8.5V; 1₁ -20A; W₁ = 100W with low voltage winding short-circuited compute: 1- the equivalent circuit constants referred to high voltage side. 2- efficiency and voltage regulation for full-load at 0.8 P.F. lagging. 3- the voltage to be applied to the high voltage side on full-load at 0.8 power factor lag when the secondary load voltage is 120V.

B- the instrument readings obtained from open and short-circuit tests on 10kVA, 450/120 50Hz transformer are: O.C. test: V₁ = 120V; I₁=4.2A; W₁ = 80W; W₁ and I₁ were read on the low-voltage side. S.C. test: V₁-8.5V; 1₁ -20A; W₁ = 100W with low voltage winding short-circuited compute: 1- the equivalent circuit constants referred to high voltage side. 2- efficiency and voltage regulation for full-load at 0.8 P.F. lagging. 3- the voltage to be applied to the high voltage side on full-load at 0.8 power factor lag when the secondary load voltage is 120V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Mr. Musa Al Biruni is analyzing a 100 kVA, 60 Hz, 7200-480V, single phase transformer, which hasthe following parameters expressed in ohms: RHS=3.06, XHS=6.05, XM,HS=17809, RLS=0.014,XLS=0.027, Rfe,HS=71400The transformer is supplying a distribution side load that draws a rated current at 480V and 75percent power-factor lagging. Sketch the appropriate equivalent circuit and determine (a) theequivalent resistance and equivalent reactance referred to high side (b) the input voltage to thetransformer
A 10MVA 138kV/13.8kV Y-Δ transformer supplies 9.1 MW of resistive load (Δ connected) at the LV side from a 138 kV power grid (infinite bus) at the HV side. Using an ideal transformer model, the line current drawn from the grid in Amperes is?
SUBJECT: Elements of Electrical Machines DesignINSTRUCTIONS: - Please write clearly and understandable way. - Write all the corresponding Given with their corresponding symbols and units. - Draw/Illustrate the diagram/circuit or drawings that is related to the problem, IF POSSIBLE, which is HIGHLY REQUIRED. - Solve in step-by-step, no shortcut - Underline twice the Final Answer.PROBLEM: A 13800 / 480 V, 3-phase transformer bank is connected as a wye-delta configuration. What must be the turns ratio of each transformer?
A radial transmission line system can be represented by a generating source connected to a three-phase transformer – (11kV/132kV, 50MVA, 10 % reactance) to which an overhead transmission line (j100 Ω) is connected. Connected to the other end of the transmission line is another three-phase transformer (132kV/33kV,50MVA, 12% reactance). This three-phase transformer located at a 33kV substation supplies a load of 30MW at a power factor of 0.8 lagging. The voltage level of the substation is to be maintained at 30kV. Use a base of 100MVA and 33kV . Use the above information to answer Q12 – Q16 12. Calculate the per unit value of reactance of the sending end transformer. a) 0.20 b) 0.25 c) 0.30 d) 0.343 e) none 13. Calculate the per unit value of reactance of the receiving end transformer. a) 0.32 b) 0.24 c) 0.41…
A network is composed of the utility having Ssc=500MVA, and an 800KVA transformer, rated at 20KV/410V (no load), whose voltage impedance is 5%, and whose load losses are 5400watts. the short circuit at the secondary of the transformer using the impedance method is: Select one: 45.8KA None of these 21.83KA 30.5KA
A 2000 VA 440/110 V transformer has been tested to determine its equivalent circuit. The equivalent impedance referred to the LV side is 0.408/_75.4 deg ohm. If the full-load voltage is 110 V and the full-load current is lagging the voltage at an angle of 43.4 deg, what will the no-load voltage be?
A network is composed of the utility having Ssc=250MVA, and an 2000KVA transformer, rated at 20KV/400V (no load), whose voltage impedance is 7%, and whose load losses are 15750watts. the short circuit at the secondary of the transformer using the impedance method is: a)27.01KA b)None of these c)25.8KA d)30KA
A 10kVA single phase transformer designed for 2000/400 V has the following constants, R1 = 5.5 ohms, R2 = 0.2 ohms; X1=12 ohms, X2=0.45 ohms. Calculate the approximate value of the secondary voltage at full load, 0.8 lagging, when the primary supply voltage is 2000V.
The figure shows an unreduced approximate L-type equivalent circuit to the High voltage (Primary) side of a 30 kVA, 4000V/120V, 60Hz transformer (Here, the parallel arms are shifted to the right, not to the left). In a transformer with parameters RH=1.6 Ohm, RL=1.44 milli Ohm, LH=21 milli Ohm, LL=19 micro Henry, RcH=160 kilo Ohm and LmH=450 Henry;Calculate the phasor V1 on the high voltage side, since it is known that a load with pf=0.6 (lagging) characteristics is connected at VL=120V on the low voltage side, and it is known that P2=20kW power is consumed.
Please Solve ASPS. A 100 kVA, 2000/400 V, 50 Hz, single phase shell type transformer has sandwitch coils. There are two full HIV coils, one full LV coil and two half LV colls. Calculate the value of leakage reactance referred to HV side if the other data given is, depth of HV coil = 4 cm depth of LV coil = 3.6 cm depth of duct between IIV and LV= 1.6 cm width of winding 12 cm length of mean turns = 150 cm HV winding turns = 200 Also calculate the per unit reactance.
element values are selected as R1 = 0.5Ω, R2 = 1Ω, J = 2A, E = 1V, β = 4 α = 1. 10Ω to A-B ends When the Ry load impedance is connected, the power consumed at this load is Norton for the circuit. Calculate using the equivalent.
α=4 β=4For the adjacent circuit, Vab=(400+5β)V is given and the source part is balanced. Since it is known as ZAN=j2α Ω, ZBN= 3α Ω and ZCN=-j3α Ω, calculate the value of the current Ib by its angle, ignoring the impedances of the transmission lines.Can you please post your solutions, it's very important