***I need the Answer of B only B. Describe a practical procedure to measure the height of your house usingtachometric surveying, list the procedure in bullet points A. A tachometric surveying was conducted to obtain some readings forinaccessible points, where it was found that the multiplying and additiveconstants are 98 and 0.1, respectively. The instrument was setup at point Candthe readings listed in the table were taken while the staff was held vertically.Calculate the horizontal distance between BM and station D. Also, calculate thereduced level of station D. Figure 1 shows a schematic view of the site.InstrumentStaffVerticalStaff readings (m)Remarksangle-4°26'stationstation1.205, 1.623, 2.041 RL of BM =0.822, 1.121,1.420 680.200mCBMC+7°18' -4°26'+7°18't.ILINE OF AXISBMD,Figure 1: Schematic view of the siteB. Describe a practical procedure to measure the height of your house usingtachometric surveying, list the procedure in bullet points.

Tachometric Surveying: Tachometric Surveying is a type of surveying in which horizontal and vertical…

Answered: B. Describe a practical procedure to…

B. Describe a practical procedure to measure the height of your house using tachometric surveying, list the procedure in bullet points.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A tachometric surveying was conducted to obtain some readings forinaccessible points, where it was found that the multiplying and additiveconstants are 98 and 0.1, respectively. The instrument was setup at point C and the readings listed in the table were taken while the staff was held vertically. Calculate the horizontal distance between BM and station D. Also, calculate the reduced level of station D. Figure 1 shows a schematic view of the site.
I need Answer of A only A. A tachometric surveying was conducted to obtain some readings forinaccessible points, where it was found that the multiplying and additiveconstants are 98 and 0.1, respectively. The instrument was setup at point C and the readings listed in the table were taken while the staff was held vertically. Calculate the horizontal distance between BM and station D. Also, calculate the reduced level of station D. Figure 1 shows a schematic view of the site.
In the two-peg test of a dummy level, the following observations are taken. On point A On point B INSTRUMENT SET UP at M 2.682 1.239 INSTRUMENT SET UP at P 1.876 0.565 Point M is equidistance from both A and B with 92 meters, while P is 2.50m away from A along the extension of line AB. Requirements: Determine the true difference in elevation between point A and B. With the level still set up at P, determine the rod reading on A and B to which the line of sight should be adjusted. If the instrument needs to be adjusted, determine the following false difference in elevation inclination of the line of sight and the error in the reading of far rod A and B instrument set up at P.
The following tacheometric observations were made from station A to stations 1 and 2. The height of the instrument above the ground was 1.52 m. Take stadia interval factor and constant as 100 and 0, respectively. If the staff was inclined by 1° to the vertical, solve for the following:a. Error in horizontal distance if the staff is inclined towards theinstrument for the line A-1. b. Error in the vertical distance if the staff is inclined away from theinstrument for the line A-2. c. If the elevation of point 1 is 115.673 m, determine the correctelevation of point 2.
Solve by Rise and fall method Ques- The following consecutive readings were taken with dumpy level and 4 m levelling staff on continuously sloping ground at a common interval of 30 m. 0.585 on A, 0.936, 1.953, 2.846, 3.644, 3.938, 0.962, 1.035, 1.689, 2.534, 3.844, 0.956, 1.579, 3.016 on B. The elevation of A was 520.450 m. (a) Enter the readings in level book. (b) Calculate R.L. of all the points by rise - fall method. (c) Apply usual arithmetical checks. (d) Determine the gradient of line AB.
The following data were obtained by a stadia measurement; vertical angle is 30deg23mins, and observed stadia intercept is 2.20m. The stadia interval factor at the measurement used 95.50m and C is 0.30m, if the height of the instrument is 1.62m, and the rod reading is taken 1.95m. Determine the D, V, S and the Difference in elevation. (D= distance, V= Vertical Distance, S= Sight distance) Topic: Tacheometric Surveying Pls answer in COMPLETE solution. DIAGRAM/ILLUSTRATION of the solution is a must, for better understanding. 3 dec places all answers. THANK YOU.
SURVEYING Given the following differential level notes: STA BS FS BM1 1.73 - TP1 2.5 3.8 TP2 2.75 1.7 BM2 3.15 3.32 TP3 2.45 3.22 TP4 3.9 2.5 TP5 2.78 3.02 BM3 - 1.77 Base on the differential leveling of note in the previous problem, if the elevation of TP3 = 267.28 m, determine the elevation of BM1
1.)An inverse method of leveling is executed between two existing concrete structures and across a concrete wall located midway between the two structures. All rod readings, as indicated in the accompanying sketch, were taken with the rod held upside down. From the data portrayed, if the elevation of A (bottom of the concrete beam of the first structure_ is 240.05 m, what is the elevation of the bottom of the concrete beam of the second structure (indicated as C)?
STA BS FS 1 5.87 2 7.03 6.29 3 3.48 6.25 4 7.25 7.08 5 10.19 5.57 6 9.29 4.45 7 4.94 a. Determine the elevation at Sta. 7, in meters if the elevation at station 1 is 392.25m. b. Determine the elevation of the instrument where the surveyor can get readings from stations 3 and 4.
In a topographic survey undertaken by Karman Surv.Corp. before any leveling is conducted. The engineersusually check whether the engineers level is in perfectadjustment. A two peg test is used to check whether theline of sight is in perfect adjustment and the followingrod readings are taken, with instrument set up near A,backsight on A is 1.623 m. and foresight reading on B is2.875 m. with the instrument set up near B, backsight onB is 1.622 m. and foresight on A is 0.362 m. Compute the difference in elevation between Aand B. What should be the correct rod reading on A togive a level line of sight with the instrument stillset up at B? What should have been the reading on B with theinstrument at A to give a level line of sight?
A Reciprocal leveling is observed across a wide river and the reciprocal level readings were takenbetween points A and B as follows. With instrument set up near A, the rod readings on A are 2.283 mand 2.285 m. The reciprocal level readings on the opposite side of the river at point B are 3.618, 3.619,3.621 and 3.622 m. With the instrument set up near B the rod readings on B are 4.478m and 4.476 m,and the rod readings on the on the opposite side of the river at point A, the rod readings are 3.143,3.140, 3.146 and 3.144.a.Compute the difference in elevation between A and B with the instrument set up near A.b.What is the true difference in elevation between A and B?c.If the elevation A is 300 m, what is the elevation of B?
Surveying Question: A differential leveling circuit starts at benchmark Concrete Benchmark (Elevation=232.051m) goes out to an unknown benchmark and then continues to a known control point (Elevation=227.975m). Two turning points are used with the measurements included in the attached table. Determine the elevation of the unknown benchmark Determine the order and class of the survey. For First order Class 1: Allowable Error= +/- 4(K)1/2 Range of Constant= m less than/equal to 4 For First Order Class 2: Allowable error= +/- 5(K)1/2 Range of constant= m greater than/equal to 4, and m less than equal to 5 (between 4 and 5) For Second Order Class 1: Allowable error = +/- 6(K)1/2 Range of Constant = m greater than/equal to 5, and m less than equal to 6 (between 5 and 6) For Second Order Class 2: Allowable error = +/- 8(K)1/2 Range of Constant = m greater than/equal to 6, and m less than equal to 8 (between 6 and 8) For Third Order, Any Class: Allowable Error = +/-12(K)1/2 Range…