B. Select the correct answer to questions 6 through 9 from the following list, and write it in the space provided. power source always speed of the armature only one strength of the field flux either decrease sometimes increase 6. In addition to armature rotation, the output voltage varies with the 7. One factor limiting an increase in output voltage is the 8. A change in the speed of rotation of the armature change in the output voltage. 9. If the field poles are saturated, an increase in the field current does not cause a(n) in the output voltage. results in a

B. Select the correct answer to questions 6 through 9 from the following list, and write it in the space provided. power source always speed of the armature only one strength of the field flux either decrease sometimes increase 6. In addition to armature rotation, the output voltage varies with the 7. One factor limiting an increase in output voltage is the 8. A change in the speed of rotation of the armature change in the output voltage. 9. If the field poles are saturated, an increase in the field current does not cause a(n) in the output voltage. results in a

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

7. Increasing the length of the air gap of DC machine reduces the Armature reaction effect. Select one: True False
analyze 3 commonly used ac motor starting methods using suitable diagrams and torque-speed curves
Due to increased armature m.m.f., the armature reaction during load condition will decrease and hence the field flux will be increased. Select one: True False
11. Why is the conduction angle greater with an inductive load than with a purely resistive load? 12. For a full-wave phase control circuit draw the output voltage and current waveforms when firing angle α = (45-X)° (Here X= 10). Consider the load to be inductive. 13. What point in a single-phase ac waveform is used as a reference point for timing the thyristor gate pulses?
Q:40) How we can get delay angle by hand calculations?
1). Briefly describe the operation of the boost chopper.2). Explain why the maximum value of the duty cycle must be limited in certain boost choppers?
A 4-quadrant DC chopper with bipolar switching operating at a switching frequency of 2kHz, is connected to a 120VDC source (Vs) and a DC motor which has a counter EMF (CEMF) of 50VDC at rated speed. The armature resistance is 2Ω and the armature inductance is 20mH. Calculate: a) Output voltage with an 80% duty cycle b) Magnitude and direction of the DC armature current with an 80% duty cycle. c) Duty cycle for a forward braking current of 10ADC. (Assume the speed has not changed due to the large inertia of the load.)
Find a) Percentage overshoot control system having the undamped natural frequency in rad/sec=8.6 and damping ratio =0.8
Why transient response? What is the importance of the transient response of a control system? ples write in deatil
A separately excited generator has no-load voltage of 125V. A certain load rated at 1200W, 120V is then connected at the terminal. Calculate the series resistance needed to connect to the armature circuit in order for the load to operate at rated condition if the armature resistance is 0.0692Ω.
It has been determined by test that thesynchronous reactance Xs and armature resistance raof a 2,300-V, 500-VA, three-phase synchronousgenerator are 8.0 and 0.1 Ω, respectively. If themachine is operating at rated load and voltage at apower factor of 0.867 lagging, find the generatedvoltage per phase and the torque angle.
A long Shunt Compound Generator delivers a load current of 20A at 200V and has armature, series field and shunt field resistances of 0.04 Ώ,0.2 Ώ and 250 Ώ respectively. Calculate the generated Voltage and the armature current. Allow 1v per brush for contact drop.