-B

Q: Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 0.8-in...

A: Given Data: Horizontal forces on pin is F = 5 kips +5 kips = 10 kips. The width of link AB and BC i...

Q: 6-44 Determine the force exerted by the cable at B and the reaction at support A of the curved bar s...

A: Given data as per question Force applied =850 N considering free body diagram of the system in Δ AB...

Q: Where is a bent material most likely to fail?

A: Let us take an example. Consider any beam applied with external bending  moment . This beam undergoe...

Q: A certain hawk can fly horizontally (i.e., not diving) at a maximum speed of 80.0 km/hr. The hawk ta...

A:

Q: A couple of magnitude M = 80 lb·in. and the three forces shown are applied to an angle bracket. (a) ...

A: (A). The single force is obtained by moving the force until its moment about the point A is equal to...

Q: Q2: Two shafts, each of 7/8 in. diameter, are connected by the gears shown in fig. Knowing that G=11...

A:

Q: For the loading shown, and knowing that beams AB and DE have the same flexural rigidity, determine t...

A:

Q: a combined heat and power system (generates electricity, steam for industrial process and provides h...

A: According to the guidelines we are suppose to solve max. 3 sub-parts of a question, please re-post t...

Q: A steady-flow thermodynamic system receives 100 lbm/min of fluid at 30 psia and 2 ft^3/lbm and disch...

A: The steady flow energy equation can be used to evaluating the power generated during the flow.

Q: Represent the following combinations of units in the correct SI form using an appropriate prefix:um....

A: Given: The given unit is U=µm-Mg. The conversion factor to convert the given unit in the correct SI ...

Q: A movable bracket is held at rest by a cable attached at C and by frictionless rollers at A and B. ....

A: Draw the F.B.D of the given bracket.

Q: A steam turbine receives steam with a flow rate of 15 kg/s and experiences a heat loss of 14 kW. Usi...

A: In turbine, the thermal and pressure energy of the fluid is converted to the kinetic energy of the s...

Q: Referring to the figure, water contained in a piston-cylinder assembly, initially at 1.5 bar and a q...

A: Given Initial pressure = 1.5 Bar Quality = 20 % = 0.2 To find Sketch the Temperature- Volume diagram...

Q: Q1.1: Determine the magnitude of the component force F in Figure and the magnitude of the resultant ...

A: Consider the diagram shown below for the resolution of the forces.

Q: Determine the bending strain energy in the simply supported beam. EI is constant.

A: Evaluate the total load on the beam as follows. F=12w0×L2+12w0×L2=12w0L If the total load is conside...

Q: 2 - The moment of a certain force ( F ) is ( 180 N.m ) clockwise about ( o ) and ( 90 N . m ) counte...

A:

Q: C7-31 Athree-bar truss is loaded and supported as shown in Fig. a function of angle e (0 ses 90°). P...

A: Understand the following configuration for the triangular truss. From the given triangular truss.

Q: Knowing that the tension in cable AC is 3875.1N, the x components of the force exerted on the plate ...

A:

Q: Two men carry a load of 2 kN by means of two ropes fixed to the weight. One rope is inclined at 45º ...

A: Answer : Given parameters Weight = 2KN Inclination of rope 1 = 45o  with vertical Inclination of rop...

Q: Knowing that P = 100 N, determine the range of values of 0 for which equilibrium of the 7.5-kg block...

A:

Q: Determine the power input for a compressor that compresses helium from 110 kPa and 20°C to 400 kPa a...

A: Given: The initial pressure of the helium is P1=110kPa. The initial temperature of the helium is T1=...

Q: The 4-mm-diameter cable BC is made of a steel with E5 200 GPa. Knowing that the maximum stress in th...

A:

Q: Determine the x and y scalar components of 22° F= 475 lb

A: Given data: Force, F = 475 lb. Drawing the x and y components of the force:

Q: 4.6 The NACA 4412 airfoil has a mean camber line given by for 0 <=<0.4 0.25 0240-()] 0.8 for 0.4 <= ...

A:

Q: A slender rod AB with a weight W is attached to two blocks A and B that can move freely in the guide...

A: Given data: weight of the rod, W = 80 N, Length (l)                   = 500 mm                      ...

Q: R9-1. The assembly consists of two A992 steel bolts AB and EF and an 6O6I-T6 aluminum rod CD. When t...

A: The problem does not specify expansion coefficients and elastic modulus for steel bolts and aluminum...

Q: For the cantilever beam and loading shown, determine the slope and deflection at the free end

A: Calculation of slope at free end  (θA)P=PL22EI                                      Where (θA)P=slop...

Q: Problem 1. A fluid flow is defined by u =2y (m/s) and v =8xy (m/s), where x and y are in meters. Det...

A: Given data: u=2y2 msv=8xy ms

Q: Engine oil at 60°C rotates as a rigid body about the z-axis in a spinning cylindrical container. The...

A: Consider a rotational fluid element as shown below. Let the mass of this element be, m=ρ.v=ρ.dA.dr ...

Q: Determine the internal resisting forces and mo- ment transmitted by section aa in the bracket shown ...

A: Shifting the 300N fore from C to B. Length CD=25Cot60º Now,

Q: A 20-kg ladder used to reach high shelves in a storeroom is supported by two flanged wheels A and B ...

A: Given Mass of the ladder = 20 Kg Mass of the man = 80 Kg To find Reaction at A, B and C

Q: While discussing throttle-by-wire systems: Technician A says that a spring on the throttle shaft pro...

A: Given that Technician A says that a spring on the throttle shaft provides the limp-home feature.  Te...

Q: A well-insulated electric oven is being heated through its heating element. If the entire oven, incl...

A:

Q: For the frame and loading shown, determine the reactions at A and C.

A: Given data Point load at point D = 30 lb. The radius of curved member AB, r = 3 in. Draw the free-...

Q: Consider a river flowing toward a lake at an average speed of 3 m/s at a rate of 500 m3/s at a locat...

A: Given: The average speed of the river is v=3 m/s. The rate of the flow of the river is V=500 m3/s. T...

Q: What is Zero displacements?

A: Displacement is the smallest distance between the final state and the initial state of the body. It ...

Q: Air enters a turbojet engine at 320 m/s at a rate of 30 kg/s and exits at 570 m/s relative to the ai...

A: Given: The inlet velocity of the air is u=320 m/s. The exit velocity of the air is v=570 m/s. The ma...

Q: Problem 1 (30 points): A 14 kg block falls through a channel which is lubricated by a thin layer of ...

A: According to the formula   shear force in walls of the blockFs=ζ×A=μdudy×A                  =0.35×V...

Q: Two kg of water is contained in a piston-cylinder assembly, initially at 10 bar and 200 °C. The wate...

A: Write the given data:

Q: The 20-mm-diameter A-36 steel rod is subjected to the axial forces shown. Determine the displacement...

A:

Q: While discussing SFI systems: Technician A says that when the injection system fires according to cr...

A: The SFI system stands for Sequential Fuel Injection System. Within the SFI system, a specially desig...

Q: A high-speed aircraft is cruising in still air. How does the temperature of air at the nose of the a...

A: The air hitting at the nose of the aircraft is generating a stagnation point. During a stagnation pr...

Q: If A and B are both made of wood and are 3 8 in. thick, determine to the nearest 14 in. the smallest...

A: Provided that both the elements A and B are 3/8 inch thick. The applied force of 800 lb will have tw...

Q: A hose of diameter 3 cm is used to drain a very large tank filled with water (=1000 kg/m3). The hose...

A: Bernaullis Principle In a fluid flow, the total energy at a point remains conserved. Pressure energy...

Q: A grinding wheel weighing 2 Ib is supported by a journal bearing at each end of the axle as shown in...

A: Given: The weight of the grinding wheel is w = 2 lb. The coefficient of friction between axle and b...

Q: Your bicycle has 10 gears, from low (easiest to pedal) to high (hardest to pedal). When you first st...

A: We know that, Bicycle in low gear means it is easy to pedal. Bicycle in high gear means it is hard t...

Q: All of the problems

A:

Q: Determine the minimum thickness of the shaft's wall.

A: The power delivers by engine, P = 150 hp The speed of the shaft, N = 1500 rpm The outer diameter of ...

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.