Be quick please A rotating circular shaft, machined from AISI 1030 Q&T* steel, is subjected to a torque that varies from a value of 20N.m to 200 N.m and to a fluctuating bending moment that varies from a value of - 500 N.m to 1500 N.m. Also an axialtensile force of 15 kN acts on the element. The torque and the bending moments have their peak values at the sametime and their frequencies are same. Find the factor of safety of the element for an infinite operation life assuming thereliability as 0.90. Use Modified Goodman Diagram and take di = 80 mm, d2 = 60 mm and r = 6 mm.TMM

given; A rotating circular shaft, machined from AISI 1030 steel fluctuating bending…

Answered: Be quick please

Engineering

Civil Engineering

Be quick please

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A compound shaft is made by rigidly bonding a steel tube of external diameter 22mm and a bronze rod of 13mm. Take Gst=80GPa and Gbr=36GPa. If 4Nm is the portion of the total torque applied to the bronze rod, calculate the angle of twist of the steel tube in degrees, correct to the 2nd decimal.
A hollow steel shaft 2660mm long is to be designed to transmit a torque of 24809kJ. Theshear modulus of elasticity, G = 82,740 GPa for steel. The total angle of twist of the lengthof the shaft is must not exceed 6 degrees. And the shear stress in the shaft must notexceed 110.32 MPa. What would be the ratio of the outside diameter to inside diameter?
The solid steel shaft carries the torques T1= 1200 Nm and T2=750 N m. Using L1=L2=2.5 m and G = 83 GPa, determine: a. draw a diagram using a double headed arrows showing the torque in each segment b. determine the shear stresses in each segment and the angle of rotation of the free end if the diameter is 100 mm. c. the smallest allowable diameter of the shaft if the shear stress is limited to 60 MPa and the angle of rotation of the free end is not to exceed 4^0.
The shaft ABCD is bearing torques at pully A, B, C, and D as shown in the figure. The magnitude of the torques on each pully and the shaft length are given. All shafts are made of a material with a modulus of rigidity of G = 80 GPa. The diameter of shafts (1) and (2) is d1 = d2 = 52 mm, and the diameter of shafts (3) and (4) is d3 = d4 = 58 mm. The bearings shown allow the shaft to turn freely. [TA = 1399 N-m, TB = 4585 N-m, TC = 2649 N-m, TD = 537 N-m, a = 0.35 m, b = 0.45 , c = 0.2 m, d = 0.35 m] Determinethe internal torque in segment (1) of the shaft.in N.m Determinethe internal torque in segment (2) of the shaft.in N.m Determinethe internal torque in segment (3) of the shaft.in N.m
The shaft ABCD is bearing torques at pully A, B, C, and D as shown in the figure. The magnitude of the torques on each pully and the shaft length are given. All shafts are made of a material with a modulus of rigidity of G = 80 GPa. The diameter of shafts (1) and (2) is d1 = d2 = 52 mm, and the diameter of shafts (3) and (4) is d3 = d4 = 58 mm. The bearings shown allow the shaft to turn freely. [TA = 1399 N-m, TB = 4585 N-m, TC = 2649 N-m, TD = 537 N-m, a = 0.35 m, b = 0.45 , c = 0.2 m, d = 0.35 m] Determinethe internal torque in segment (1) of the shaft. Determinethe internal torque in segment (2) of the shaft. Determinethe internal torque in segment (3) of the shaft.
A solid constant-diameter circular shaft is subjected to the torques of TA = 460 lb·ft, TB = 1000 lb·ft, TC = 880 lb·ft, and TD = 340 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6. (b) If the allowable shear stress in the shaft is 7200 psi, what is the minimum acceptable diameter for the shaft?
The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation (in degrees) of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze. Answer in 1 decimal place
A two pinned end bars AB (Copper), ? = 850 ??2, ? = 120 ??? and BC (Aluminum), ? = 1000??2, ? = 70 ??? is subjected to a horizontal force of 100 ?? applied at pin B as shown in the figure, determine the horizontal displacement of pin B.
A solid 1.250-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 295 lb-ft and TD= 95 lb-ft, acting in the directions shown. Assume a = 48 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 14 ksi, determine the maximum torque TC that can be applied to the shaft. [Answer: TC = 542 lb ft]
Specifications of the steel rod at B. L=2 meters diameter= 25 mm E= 200 GPa Show complete solution 1. Draw the shear force and bending moment diagrams. 2. Determine the deflection at A
The stepped shaft ACB shown in Figure bellow is fixed at both ends and loaded by a torque TO at point C. Segment AC having solid circular cross section and segment CB having hollow circular cross section. If the shafts material is steel with shear modulus G = 11 x 10°psi, and the torque is To = 8,000 lb-in. Calculate: (a) The maximum and the minimum shear stress in segment CB. (b) The maximum and the minimum shear strain in segment CB. (c) The angle of rotation 0, at the cross section where the torque To is applied.
A circular copper rod having length of P inches is to be twisted by torques 6.5P lb.in until the angle of rotation between the ends of the rod is 3.0°. If the allowable shear strain in the copper is 0.0006 radians, solve for the maximum permissible diameter of the rod? (Where P is 27