Benzene is flowing through a pipe at a rate of 140lb/hr. The specific gravity of benzene is 0.879. The outside diameter of the pipe is 2 inches and the thickness is 0.154 inch. Calculate the 1.)Velocity in ft/s 2.)Mass Velocity in lb/ft^2-s 3.)Volumetric flowrate in gal/min.

Benzene is flowing through a pipe at a rate of 140lb/hr. The specific gravity of benzene is 0.879. The outside diameter of the pipe is 2 inches and the thickness is 0.154 inch. Calculate the 1.)Velocity in ft/s 2.)Mass Velocity in lb/ft^2-s 3.)Volumetric flowrate in gal/min.

Name: Benzene is flowing through a pipe at a rate of 140lb/hr. The specific
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Benzene is flowing through a pipe at a rate of 140lb/hr. The specific gravity of benzene is 0.879. The outside diameter of the pipe is 2 inches and the thickness is 0.154 inch. Calculate the 1.)Velocity in ft/s2.)Mass Velocity in lb/ft^2-s3.)Volumetr

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 14RQ: Four pounds of a gas occupy 10 ft3. What would be itsdensity and specific gravity?

See similar textbooks

Similar questions

Given the sketch shown below, the diameter of the plunger Dp = 8 cm. The Ram diameter is Dr = 48 cm. The efficiency is 100%, the stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2kN. Find: A) the force f1 exerted on the plunger. B) the number of strokes needed to raise the load given above by a distance of 10 cm. C) the volume of oil pumped if the load moves by 20 cm ( using plunger force in a ) D) what will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 8 cm.
Water flows through a horizontal pipe at a velocity of 30 ft/s, flowing to the pipe narrows down to smaller size, the velocity increases to 60 ft/s. What is the difference between the pressures at two points?
A piston with area 2cm2 is moved at a speed of 1.5cm/s. What is the velocity in m/s if the outlet is 15mm2?
1. A double-acting air compressor has 18 x 12 inches, 626 rpm. Determine the volume displacement in ft^3/min Answer in whole number 2. An air compressor piston displacement is 6,308 cm^3/min when operates at 964 rpm and volumetric efficiency of 75 %. Determine the capacity of air compressor in cm^3 per min.
The average flow for the Mississippi River is approximately 1,500 cfs. It is assumed that one-fourth of this flow would be available to develop power at a dam shown below. a). what would be the annual energy in kilowatt-hours that would be produced with an overall average of 88% efficiency? b), What would the pressure P in psi?
Water flows through a horizontal pipe of cross sectional of 20 cm2. At one section, the cross sectional area is 4 cm2. the pressure difference is 29.4 psi. How many cubic meters of water will flow out of the pipe in 1 min?
angular velocity is equal.....................
In a hydraulic system, a piston with a cross-sectional area of 21 square centimeters pushes on an incompressible liquid with a force of 38 newtons. The far end of the hydraulic pipe connects to a second piston with a cross-sectional surface area of 100 square centimeters. What is the force on the second piston?
A ship with vertical sides near the water line, weighs 40 MN and draws 6.7 m in salt water (specific gravity = 1.026). Discharge of 2 MN of water ballast decreases the draft to 6.4 m. What would be the draft d of the ship in fresh water?
In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and 100 cm. Find the distance moved by the load piston if 10 strokes are applied to the effort piston . Given : Stroke length of the effort piston is : 50 cm . Distance moved by Load piston : ____________m
The rate of water supply to a hydraulic crane is 90 liters per minute at a steady pressure of 70 bars. Find the input power and the efficiency if the output is 7.5 kW. The power in watts is the product of water supply pressure in N/m sq. and volume flow in M' per second.
A fluid mass occupies 2m^3 Calculate the density, specific weight, and specific gravity if the fluid mass is: a.) 4kg b.) 8kg c.) 15k