Binary data are transmitted at rate of 10 bit/sec, over a microwave link having aBW of 3MHZ.Assume that the noise power spectrum density (PSD), at the receiver i/p is-10= 10W/Hz. Find the average power required at the receiver i/p for Coh. FSK(synch. FSK) and DPSK Signaling schemes to maintain probability of error less than orequal to 10.

Tsolution solution is given below

Binary data are transmitted at rate of 10 bit/sec, over a microwave link having a BW of 3MHZ.Assume that the noise power spectrum density (PSD), at the receiver i/p is -10 = 10 2 W/Hz. Find the average power required at the receiver i/p for Coh. FSK (synch. FSK) and DPSK Signaling schemes to maintain probability of error less than or equal to 10.

Binary data are transmitted at rate of 10 bit/sec, over a microwave link having a BW of 3MHZ.Assume that the noise power spectrum density (PSD), at the receiver i/p is -10 = 10 2 W/Hz. Find the average power required at the receiver i/p for Coh. FSK (synch. FSK) and DPSK Signaling schemes to maintain probability of error less than or equal to 10.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For an H3E system with 80 percent modulation, what would be the i.) total transmitted power in W and ii.) remaining sideband power in W of the AM signal if the unmodulated carrier power is 1kW?
Let the center frequency of the wireless link be 901 MHz.(a) If the distance between Tx and Rx radios and reflectors around them is up to 10m, what is the maximum propagation delay tmax?(b) Let Rb = 5000 bits/s (chips/s). Under these conditions, are reflection paths resolvable?
c) i) Consider a noisy continuous communication channel of bandwidth B = 1 MHz, which is perturbed by additive white Gaussian noise whose total spectral power is N0B = 1 W. Continuous signals are transmitted across such a channel, with average transmitted power S = 1,023 W. Give a numerical estimate for the channel capacity, in bits per second, of this noisy channel.
A. How many numbers of constellation points exist in phase for 3bit ASK? B. What happens to the radio wave propagation when the frequency is below critical angle? C. If the mark frequency and space frequency are same then what happens to FSK? D. What is the Carson’s rule? E. What is the Maximum data rate in a minimum channel bandwidth is ? F. What is radio horizon and where is it used? G. What are the phase angle limitations of a BPSK? H. What is the change in channel capacity when two number of bits are increased?
: Suppose you have the following information signal ?(?) = 4sin⁡(4000?? + 90) modulates with the following carrier signal ?(?) = sin⁡(4000000?? + 90) to produce the 8KHz peak frequency deviation. Compute: 1. The FM expression in the time domain. 2. The frequency sensitivity constant. 3. FM signal bandwidth.
5. The following data is available: fc= carrier frequency = 750kHz, Ac= maximum amplitude of the unmodulated carrier = 10V fm= modulator frequency = 300Hz-8kHz modulation index m=0.5 a) What is the frequency of the upper sideband? b) What is the frequency of the lower sideband? c) What is the amplitude of the modulating signal? d) What is the maximum amplitude of the envelope of the modulated signal? e) What is the minimum amplitude of the envelope of the modulated signal? f) What is the bandwidth of the modulated wave? g) Write an expression for the modulated wave
In AM Transmitter, Does adding modulation to the RF carrier increase the output power of the signal? If yes, how many times does the power increase in the circuit for 100% modulation? for 75% modulation? for 50% modulation? Is is better to modulate at 100% than 50%?
Consider a mobile system at 900 MHz carrier frequency, and with 25-kHz bandwidth, that is affected by thermal noise (noise temp Te = 300k). Antenna gains of Tx and Rx sides are 8dB and -2dB respectively. Cable loss at Tx is 2dB. The noise figure at Rx is 7dB. The required operating SNR is 18dB and desired range of coverage is 2km. The break point is at 10dB up to which the path loss is given by [ ] , beyond that point the path loss exponent is 3.8, and the fading margin is 10dB. What is the minimum Tx power required?
A 4 GHz carrier is DSB-SC modulated by a low pass message signal with maximum frequency of 2 MHz . the resultant signal is to be ideally sampled. The minimum frequency is?
For double sideband (DSB) signal f) What is the difficulty of synchronous demodulation (coherent detection)? g) Compare between the ordinary amplitude modulation (AM), and double sideband (DSB) modulation in terms of transmitted power, complexity of demodulation, receiver cost, and bandwidth
Consider an AWGN channel with bandwidth 50 MHz, received signal power 10 mW, and noise density No (Noise Power/Bandwidth) = 10−9 W/Hz. (Use two decimal places) (a) What is the information capacity (Mbps) in the system? (b) By doubling the received power, What is the information capacity (Mbps) in the system? (c) How much does the capacity (Mbps) by doubling the channel bandwidth?
Wireless communication Determine the minimum C/N ratio for an 8-PSK system when the transmission rate is 60Mbps, the minimum energy of bit-to-noise density ratio is 15 dB, and the receiver bandwidth isequal to the minimum Nyquist frequency.