Bucket-A and block-C are connected by a rope that passes over the fixed cylindrical transition-piece at B. The coefficients of friction at ALL surfaces are u, = 35%, and uk = 25%. Determine the maximum bucket + contents weight, W, that can be applied without dragging the block up the ramp. В 200 lb A

Bucket-A and block-C are connected by a rope that passes over the fixed cylindrical transition-piece at B. The coefficients of friction at ALL surfaces are u, = 35%, and uk = 25%. Determine the maximum bucket + contents weight, W, that can be applied without dragging the block up the ramp. В 200 lb A

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.3P: Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair...

See similar textbooks

Similar questions

The cone clutch transmits the torque C through a conical friction surface with cone angle . The inner and outer radii of the friction surface are a and b, respectively. The left half of the clutch is keyed to the shaft, and the right half drives a machine (not shown) through a gear attached to its outer rim. Assuming uniform pressure on the friction surface, show that the maximum torque that can be transmitted by the clutch is
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The two 6° wedges in Fig. P5–21 are used to adjust the horizontal position of the 200-kg block. Determine the minimum force P required to move the block. The static friction angle at all contact surface is 15°.
Box A weighs 1000N and has a height of H1=3m and width W1=2m. Box B weighs 800N. the static friction coefficient between the boxes is uA=0.7 and the static friction coefficient between box B and the ramp is uB=0.5. Find the max allowable angle for the following instances where no motion occurs, box A and B remain stationary. 1) Box A slides, Box B remains stationary 2) Box A tips, Box B remains stationary 3) Box B slides, Box A remains stationary on block B
The weight of the motorcycle is 151 kg and the weight of the driver is 64 kg. Dimensions: l1 = 0,31 m and l2 = 0,23 m Determine the required frictional force.
Two hemispheres having an inner radius of 2 ft and wall thickness of 0.25 in. are fitted together, and the inside pressure is reduced to -10 psi. If the coefficient of static friction is ms = 0.5 between the hemispheres, determine (a) the torque T needed to initiate the rotation of the top hemisphere relative to the bottom one, (b) the vertical force needed to pull the top hemisphere off the bottom one, and (c) the horizontal force needed to slide the top hemisphere off the bottom one.
A 20 kg block is held in place on an incline plane as shown by a rope that passesover a frictionless pulley at B and then over a fixed cylinder at C where thecoefficient between the rope and the fixed cylinder is 0.2. Given an angle ofincline, A = 25°, if a force of P = 200 V is applied to the end of the rope,(a) Will the block move if the coefficient of static friction between the block and theinclined surface is M, = 0.56?(b)If impending motion exists, will the block tip or slip?
PROBLEM: To prevent a box from sliding down an inclined plane, student A pushes on the box in the direction parallel to the incline, just hard enough to hold the box stationary. In an identical situation, student B pushes on the box horizontally. If the weight of the box w= 20.0 N, the angle made by the incline with the horizontal θ=25o, and the coefficient of static friction µs=0.16, who has the easier job?
A 2.4 m ladder rests on a vertical wall as shown in the figure. The ladder has seven rungs and the rungs are spaced 0.30 m apart, and the top and bottom rungs are 0.30 m from their respective ends of the ladder. Surfaces at A and B both have the same coefficient of friction. If a worker weighs 630 N and stands on the middle rung, determine the minimum value of the coefficient of friction so that the ladder does not slide. Neglect the weight of the ladder.
A 100 N force acts as shown on a 30.6 kg block placed on an inclined plane. The coefficients of friction between the block and the plane are µs = 0.25 and µk = 0.2. Determine whether the block is in equilibrium and find the value of the friction force.
body resting on a rough horizontal plane requires a pull of 300 N inclined at 40º to the horizontal plane just to move it. It is found that a push of 150 N inclined at 40o to the x-axis can also make the body to move. Determine the weight of the body and the coefficient of friction.
Two blocks A and B weighing 3 kN and 15 kN, respectively, are held in position against an inclined plane by applying a horizontal force P as shown in Fig. Find the least value of P which will induce motion of the block A upwards. Angle of friction for all contact surfaces is 12°.7.