The floor of an apartment building shown is subjected to a uniformlydistributed dead load of 1.5 kPa and a uniformly distributed live load of 1.9kPa over its surface area. Determine the service (ASD) reaction (kN) ofbeam BG that will be transferred to the girder at G.GirderFloor beamColumnABHFH-LG-IoHHM4 at 7.5 m 30 mDNE2 at 12 m =24 m

Answered: building shown 5 kPa and a uni…

Engineering

Civil Engineering

building shown 5 kPa and a uni Determine the s forred to the gi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: a reinforced concrete beam is 450 mm wide with an effective depth of 580mm, fc'=21 MPa, and fy=275…

Q: a speed of (50 cm/sec) through the first section of a pipe with a diameter of (25 cm). The diameter…

Q: Problem 2: The cantilever beam shown in Figure consists of a W8 x 31 structural steel wide- flange…

Q: Find the shear and moment equations for the beam loaded as shown if P = 444 lb, W = 245 lb/ft, a =…

Q: vane and the fluid, the magnitude of the force exerted by water on the cart in the x-direction, in…

Q: 20. A sewage treatment plant is designed to treat sewage from a population of 25,000 PE. (i) (ii)…

Q: A. lem 5m 4m Determine the max positive and negative shear and max positive and negative moment at…

Q: What is the head loss between points A and D when the flow rate is 6 m Sofor the flow rate for each…

Q: W₂ = 30 kN/m W₁ = 10 kN/m B A L=12 m Given: E-200x10³ MPa, I-120x106 mm² For the beam shown, you are…

A: Let's solve using moment area method (MDM) Taking RB as redundant

Q: 600 N/m 3 m 2 m R₁ R₂ Label left end of beam as A, midpoint as B and right end as C. Using the…

Q: Time Delay control system: A level control system. The time delay between the valve adjustment and…

Q: Part 1: Some Discrete Probability Distributions 4.2 Discrete Uniform Distribution 4.3 Binomial…

A: in this question , 3 examples is asked about probability

Q: Statics, Civil Engineering The screw eye is exposed to the two forces shown. Express each force in…

A: Express each force in cartesian vector form Determine the resultant force and the direction angles…

Q: The roof of a single-story storage building shown is subjected to a uniformly distributed load of…

Q: Conclusion about the appropriability of structural steel as a structural material.

A: Conclusion:- Today, practically all the industries have major applications of the structural steel.…

Q: At a section in the triangular channel the average velocity is 8 ft/s. Determine (a) the critical…

Q: The 300-kg wheel has a radius of gyration about its mass center O of ko = 400 mm (Figure 1) < 1 of 1…

Q: Figure 1 shows a warren truss bridge of span 36m and height 8m. The trusses are spaced at 5m c/c,…

Q: From the given loaded cantilew

Q: b) List factors which affect the quantity of storm water flow for design of sewer system?

A: This question is related to the Hydrology Engineering. In this question ask only for listing factors…

Q: Example 18.4: Find the Horizontal thrust 'H' at each support. 40 KN 30 kN 20 kN 10 kN. ZU 45° 60° H…

Q: H₂ = 4 m f=0.15 D₁ = 50 mm H₁ = 4 m 25 m L = 100 m A. Two tanks A and B were connected by a 50…

Q: Determine the maximum deflection of the cantilevered beam. The beam is made of material having an E…

A: Asked: To determine the maximum deflection of the cantilever arm. Given: E = 200 GPa or kN/mm2 I…

Q: The corners of the square plate deform as indicated. determine the angular strain at A with respect…

A: The given figure is shown below:

Q: ow is the text size for dimensions and text managed in Revit? Setting the dimension style to the…

A: This question is related to AUTOCAD from Civil Engineering .

Q: A conical water tank has its top at ground level (consider this to be the x-axis) and its base 12 ft…

A: Answer We are given radius of cone R = 4ft Height of cone H= 12 ft Weight of water γw = 62.4…

Q: A turbine developing 15000 hp and it turns the shaft at 300 rpm. The propeller which is attached the…

Q: A gravity settling tank is to be used to clean waste water from an oil refinery. The waste water…

A: given- Q=10000 gal/min=0.06313 m3/saverage particle size=1000+10×10-62m=5.05×10-4 moil…

Q: Dramp that is inclined at a morizontal width x of the ra

Q: 2/122 The particle P starts from rest at point A at time t = 0 and changes its speed thereafter at a…

Q: Q1) Using a system similar to that shown in figure, if air pressure p = 50 kPa., and the depth h1 =…

Q: 7-40. SAE 30 oil at 68°F flows through the piping system shown in Figure 7.38. (a) If Q₂ = 20 gpm,…

Q: Determine the bending moment 7.92 ft to the right of point B for the beam shown belowif P = 500 lb,…

Q: - A 588 cm³ volume of moist sand weighs 1010 gm. Its dry weight is 918 gm and specific gravity of…

Q: on Eq. (5.1zu). probable construction cost difference. 5.12. Design the shear reinforcement, using…

Q: A circular aluminum alloy [E = 70 GPa; a= 22.5 x 10-6/°C; v=0.33] pipe has an outside diameter of…

Q: Problem 3-Determine the moment applied at point F to achieve equilibrium of the system. Use the…

Q: B. Write shear and moment equations for the beams in the following problems. In each problem, let x…

Q: below the crown C. The arch carries the load system as shown in Fig. 11.15. Determine the horizontal…

Q: 8. A section of two-lane, two-way rural road has a 4km length of sustained 5% grade with following…

Q: A 12 kN/m -4 m- B -4 m- 4 m- 12 kN/m D

Q: (i) Determine the peak flow rate (in m³/d) generated by the population (ii) Determine the minimum…

Q: he floor of an apartment building shown is subjected to a uniforml stributed dead load of 1.5 kPa…

A: Given:- udl dead load=1.5kPa udl live load=1.9KPa To find:- factored ASD

Q: For the beam shown, calculate the maximum tensile bending stress (in psi) if P = 2088 lb, Q = 8044…

Q: Based on the figure below, solve for the following items: a. Total Volume of Concrete of Footing…

A: To Determine a. Total Volume of Concrete of Footing (considering the wastage) in cubic meters. b.…

Q: Righting Moment • Overturning Moment . Factor of Safety Against Sliding . Factor of Safety Against…

Q: ACTIVITY 3- Beam Analysis Analyze the loaded beam as shown. Be guided as follows: a. Solve for the…

Q: ry weight is 918 gm and specific s, G is 2.67. Assuming density /cm³, the void ratio is

Q: Problem 7 - 73 A water district which serves a suburban community needs a new water transmission…

Q: A beam is loaded and supported as shown below. By area moment theorems, determine: (a) All support…

Question

The floor of an apartment building shown is subjected to a uniformly
distributed dead load of 1.5 kPa and a uniformly distributed live load of 1.9
kPa over its surface area. Determine the service (ASD) reaction (kN) of
beam BG that will be transferred to the girder at G.
Girder
Floor beam
Column
A
B
H
FH-
L
G
-Io
H
H
M
4 at 7.5 m 30 m
D
N
E
2 at 12 m =
24 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Pricing masonry, carpentry and finishing work

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Practical application: A one-lane bridge consists of a 10-in.-thick, 16-ft-wide reinforced concrete slab sup- ported on two steel girders spaced 10 ft apart. The girders are 62-ft long and weigh 400 lb/ft. The bridge is to be de- signed for a uniform live load of 700 lb/ft acting over the entire length of the bridge. Determine the maximum reac- tion applied to an end support due to dead, live, and im- pact loads. The live load may be assumed to act along the centerline of the deck slab and divide equally between the two girders. Each concrete curb weighs 240 lb/ft and each rail 120 lb/ft. Stone concrete has a unit weight of 150 lb/ft3 . Assume an impact factor of 1.33.
A 6-m simply supported beam AB supports a trapezoidally distributed load . The intensity of the load varies linearly from 25 kN/m at support A to 50 kN/m at support B. What is the reaction at A and B and total reaction at the supports in kN?
In the horizontal beam loaded with a uniformly distributed load(UDL) and concentrated loads as shown, determine the reaction atthe hinge and roller supports on points A and B, respectively.Figure:
The reinforced concrete T-beam below is required to support a roofing system. The loads include a superimposed dead load of 20 kN/m, a live load of 25 kN/m, and a snow load of 10 kN/m. Determined: a) The maximum factored distributed load the beam must support according to Table 4.1.3.2 of the NBC 2020; (b) The end reaction forces; and c) The maximum shear force and maximum bending moment. Plot the shear and bending moment diagrams
The canopy of a storage building shown in Figure SM-32 is spaced 2.5 m apart. The wind load normal to the roof surface is 1.44 kPa. Determine the following:1. The total reaction at D.2. The force in member CG.3. The force in member FG.
A fixed crane has a mass 1000kg and is used to lift a 2400 kg crate. It is held in place by a pin at A and rocker at B. The center of gravity of the crane is located at G. The vertical comment of reaction at pin A is.
A beam crane was subjected to a moving distributed load created by the hoist trolley. The length of the beam crane is 15 meters and the distributed load produced by the hoist trolley is 125kN/m. Compute the maximum load it creates and also its maximum moment.
The beam shown in the Fig.is 7m long with EI = 200MNm^2 Let P = 10 kN Determine the following: a. Reaction at A.b. Constant.c. Slope at 2m from A.d. Deflection at 2m from A.
The beam of flexural rigidity EI is clamped at both ends and subject to a uniformly distributed load extending along the region BC of length 0.60L. If w = 10 KN/m and L = 4 . What is the value of the reaction RA in KN? Three decimal places.
The floor system used in a school classroom consists of a 4-in.reinforced stone concrete slab. Set a = 10 ft, b = 30 ftLoading: 4 inches reinforced stone concrete slab = 0.15 k/ft³LL for classrooms = 0.04 k/ft² Using “No.10-11” problem. Set a = 10 ft and b = 15 ft. What is the reaction at B and F?a. 5.50 kb. 4.50 kc. 6.50 kd. 7.50 k What is the magnitude of the triangular loading that acts along girder ABCDE?a. 0.45 k/ftb. 0.55 k/ftc. 0.65 k/ftd. 0.75 k/ft Using “No.10-11” problem. Set a = 7.5 ft and b = 20 ft. What is the loading that acts along joist BF?a. 0.475 k/ftb. 0.575 k/ftc. 0.675 k/ftd. 0.775 k/ft What is the loading that acts alongside girder ABCDE.a. 4.75 kb. 5.75 kc. 6.75 kd. 7.75 k
The end of the boom O shown is subjected to three concurrentand coplanar forces. Determine the magnitude and direction of theresultant force.
Your team is tasked to design the supports for a beam for large air conditioner units. The beam will carry only one unit initially, but the facility may expand in the future. According to the manufacturer's literature, the air conditioner unit will apply a uniformly distributed load on the beam. Determine the reactions and draw the shear and bending moment diagrams for the beam subjected to one air-conditioner unit using the slope-deflection method.