Built-up column 10 m long consists of W350x90 with two 12 mm thick plates welded to form a box section 250 mm as shown. The colhumm is fixed at both ends and braced (assume hinged) at the midheight about the weak axis. Assume F-248MPA. Use the theoretical values for the effective length factors. Compute: a. Effective slenderness ratio with respect to x-axis. b. Effective slenderness ratio with respect to y-axis. c. Compute the axial load capacity. 350 mm X Properties of W350x90 be = 250 mm tr= 16.40 mm d = 350 mm tw=9.50 mm I = 266 x 10° mnm Iy = 44.54 x 10° mmt A = 11.550 mm

Built-up column 10 m long consists of W350x90 with two 12 mm thick plates welded to form a box section 250 mm as shown. The colhumm is fixed at both ends and braced (assume hinged) at the midheight about the weak axis. Assume F-248MPA. Use the theoretical values for the effective length factors. Compute: a. Effective slenderness ratio with respect to x-axis. b. Effective slenderness ratio with respect to y-axis. c. Compute the axial load capacity. 350 mm X Properties of W350x90 be = 250 mm tr= 16.40 mm d = 350 mm tw=9.50 mm I = 266 x 10° mnm Iy = 44.54 x 10° mmt A = 11.550 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A built-up section consisting of W 350 x 90 with two 12 – mm plates welded to form a box section as shown in figure. The section is used as a column 10 meters long. The column is fixed at both ends, and braced at mid height about the weak axis (Y-axis). Use Fy = 248 MPa a. Determine the effective slenderness ratio of the column with respect to lateral buckling about the x-axis. b.Determine the effective slenderness ratio of the column with respect to lateral buckling about the y-axis. c.Determine the axial load capacity of the column in kN.
find Pb, Mb and eb for the column shown where h is the horizantal length and b is the vrtical length as shown. given a claer cover of 1.5''
The W350x90 section is used as a column 10m long. The column Is fixed at one end and hinged at the other end. Braced at mid height about the weak axis (Y-axis). Use Fy = 248MPa Properties of W350_x 90:, bf = 250 mm d = 350 mm tf = 16.4 mm tw = 9.5 mm lx = 266 x 106 mm4 ly = 44.54 x 106 mm4 A = 11550 mm2 a) Determine the effective slenderness ratio of the column with respect to lateral bucking about the x-axis. b) Determine the effective slenderness ratio of the column with respect to lateral bucking about the y-axis. c) Determine the axial load capacity of the column in kN using NSCP.
A tied column shown below is bent in a single curvature about the y-axis. Determine the following if K = 1.0, the column is braced against sidesway, fc’ = 27.6 MPa, fy = 414 MPa, Ec =4700√fc′.a. Critical load ( Pc ) using Euler’s formulab. Moment magnification factor, δbc. Equivalent eccentricity of the column section, e
An axially loaded tied column must sustain the following service loads: Total dead load = 1600 kN live load = 1000 kN required strength, U = 1.2D + 1.6L reduction factor = 0.65 f'c = 28 MPa fy = 420 MPa determine the required number of vertical bars to be distributed equally on all sides of the column if the column is 500mm square using bar diameter = 20mm a. 8, b. 4, c. 10, d. 12
Determine the maximum design load N* of a concentrically loaded 310UC96.8 compression member of Grade 300PLUS steel if the effective length about each axis is 4.0 m. (2759 kN)
The W350x90 section is used as a column as a column 10 m long. The column is fixed at one end and hinged at the other end. Braced at mid-height about the weak axis(y-axis). Properties of W350x90 are: bf=250mm Ix=266x10^6mm^4 d=350mm Iy=44.54x10^6mm^4 a)Determinethe critical effective slenderness ratio of the column. b)Determine the axial load capacity of the column using NSCP. please answer this, thanks ☺️
A W8x35 steel column has unsupported length of 8m. Using A36 steel, compute for the ultimate axial load capacity (in kN) if both ends are a.) PINNED b.) FIXED? Neglect local buckling. W8x35 Properties A = 6645.15mm^2 lx = 52.45 x 10^6 mm^4 ly = 17.69 x 10^6 rx = 88.9 mm ry = 51.56mm
The cantilever beam AB of length L = 8ft carries a uniformly distributed load of intensity wo = 400 lb/ft, which includes the weight of the beam. Compute the maximum displacement if the beam is W12x35 section with I = 285 in4 and E = 29 x 106 psi.
A 299mm x 305mm Apitong rectangular column with an effective column length of 3m has Fc = 9.56 MPa (parallel to grain), Fc = 2.20 MPa (perpendicular to grain), E = 7310 MPa. Calculate the maximum safe axial load P in KN that it could carry.
A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8 m long, pinned at the top fixed at bottom with additional lateral support at mid height in the weak direction. The properties are as follows: Ag = 14,500 sq.mm, Ix= 258.6 x10^6 mm ^4 Iy=84.375 x 10^6 mm^4. 59. If the columns sustains a service axial dead load of 1 490 KN Calculate the safe service axial live load in KN by ASD.
P10.10. A W27×94 section of A572 Grade 50 steel 34 feet long, it is used as a simply supported beam. It is subjected to a factored concentrated load of 90 kips at 12 feet from each support. In addition, the beam is subjected to a factored moment of 340 kips-ft at its left end (counterclockwise). Neglect the self-weight of the beam in the calculations, and check whether the beam is safe according to the LRFD. Lateral support is only provided at the ends and load points.