By three-moment equation, determine the moment at support B (in kN-m, magnitude only). Use F = 120 KN, P = 118 kN, w = 46 kN/m, a = 4 meters. Supports A, B, and C are simple supports. ROUND OFF TO TWO DECIMAL PLACES. W F, P A В a Гa/3 a/3 a/3

By three-moment equation, determine the moment at support B (in kN-m, magnitude only). Use F = 120 KN, P = 118 kN, w = 46 kN/m, a = 4 meters. Supports A, B, and C are simple supports. ROUND OFF TO TWO DECIMAL PLACES. W F, P A В a Гa/3 a/3 a/3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the vertical movement of the load P

A: Given:- P=100kN For Steel:- L=4m A=300mm2 E=200GPa For Aluminum:- L=3m A=500mm2 E=70GPa To find:-…

Q: Using Three Moment Equation, determine all reactions at supports also, determine shear and bending…

A: To calculate the moment of inertia…

Q: a/3 a/3 a/3

Q: Determine the magnitude of the 15 point force in member CD using method of section * 10 kN B D 60°…

Q: Compute the force in BD in kN. P1 = 51 kN, P2 = 53 kN and x = 5.3 m. write numerical value only and…

A: P1=51kN P1=53kN To find force in member BD

Q: 3. Compute the moment of force F=450 lb and of force P= 361 Ib about point A, B, C and D. А. P D

Q: 48 kN/m 32 kN/m A TB C - 9 m - 6 m

Q: By three-moment equation, determine the moment at support B (in kN-m, magnitude only). Use F = 121…

A: Given data:

Q: Question 1: a) Use Slope Deflection Method, determine the moment that each member exerts on the…

A: As explained earlier, the slope-deflection method may be applied to analyze statically determinate…

Q: A flag pole shown is supported by three tension wires AB, AC, and AD to resist an uplift force P =…

Q: For AC Beam Below Determine Moments and Reactions at Supports by Moment Distribution Method. 10 kNm

Q: Q2: Determine the moment that each member exerts on the joints at C and D. Assume the supports at A,…

Q: W=1090 KN/m Using Three Moment Equation, determine all reactions at supports also, determine shear…

A: A bending moment is essentially a power that makes something twist. Assuming the article isn't very…

Q: Using portal method, Calculate for the shear force in kN at member FC a = 12.6 kN, b = 27.2 kN, c =…

Q: For the bar shown below, find the shear force and bending moment at point A. The cross section of…

A: Given :

Q: Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the…

Q: Q2: Using the slope deflection method, determine the moments at A, B, and C and the support…

A: Given system:

Q: 31 - Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m.…

A: given beam

Q: Determine the reaction forces and moments at points A, B, C, and D using cantilever method. Note:…

Q: The figure shows a combined footing supporting two columns, A and B. Determine the length Z so that…

A: Load at point "A" = 115kN Load at point "B" = 215 kN The uniform pressure under soil, w = 115+215…

Q: G 67.5 kN 3.6 m -D -112.5 kN E 3.6 m IA B C 6 m +4.5 m Use portal method to analyze the frame.…

Q: Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the…

Q: For the beam shown, draw the shear diagram (9 pts.) and bending moment diagram (9 pts.). Use any…

A: C

Q: Draw the FBD, write equations of equilibrium, and solve for ALL support reactions. Determine shear…

A: the given beam is determinate beam so that we can analyze the beam by the application of the…

Q: 3. Determine the internal normal force, shear force, and bending moment at point B. 45 kN B 15 kN…

Q: D E F 225 kN- 6 m B 6 m -6 m Using Cantilever Method, determine the Shear force at EF in kN.

Q: By comparing the result between Slope Deflection Equation and Modified Moment Distribution Method,…

A: Given A beam Required By comparing the result between Slope Deflection Equation and ModifiedMoment…

Q: Question For structure below, complete the missing loading and support data NB: If support A is a…

A: Given data:-

Q: For the frame below, F = 9.9 kips, a = 3 ft, b = 5 ft, and c = 3 ft. Determine the magnitude of the…

Q: M(N) Problem 8. Draw the load and shear diagram from the given moment diagram. 3.600 2m 5.625 3m…

Q: M N 35 kN 4.8 m L 70 kN- J K 4.8 m 70 kN E F G H |4.8 m A D 9 m – 6 m - 8 m

A: The cantilever method is generally helped to calculating shear forces and moments developed in beams…

Q: Situation 2 Gate AB in Figure 1 is a regular hexagon with perimeter of 18m. It is hinged at A and…

A: The center of gravity is defined as the place at which the mass of a set of elements is thought to…

Q: Determine the value of force F, force P and moment M. Note: Size of each box is 1 meter by 1 meter…

A: In mechanics when anybody is subjected to force then due to that forces effect or reaction act at…

Q: Q2: Determine the moment that each member exerts on the joints at C and D. Assume the supports at A,…

Q: 10 KN/m 6m 3m Derive the shear function of segment AB in terms of x. Derive the moment function of…

A: To draw SFD and BMD

Q: W=1317 kN/m Using Three Moment Equation, determine all reactions at supports also, determine shear…

A: Given, E=2.15×107KPa IAB=1120.250.503=2.604×10-3 m4IBC=1120.350.703=0.010 m4ICD=1120.450.903=0.027…

Q: P y 30° 1

Q: If the resultant of the loads shown passes through point B, determine the equivalent force-couple…

Q: 6 KNIM 45 KN/m B 行1个十7 2.6 to

Q: Determine the internal moments in each support using either Slope-deflection method or Moment…

Q: Determine planar support reactions as well as normal force, shear force, and bending moment…

A: The algebraic total of the vertical forces that applies at any point of a planar to the right or…

Q: Q9\ sketch the axial load, shear force and bending moment diagrams. 30 kN/m C 2 m 40 kN 40 kN 2 m A…

A: Solution Draw the given Diagram

Q: Replace the 4.4-kN force by an equivalent force-couple system at (a) point O and (b) point B. Give…

Q: Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the…

Q: 9 - Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m.…

A: Free Body diagram of the given problem:

Q: By three-moment equation, determine the moment at support B (in kN-m, magnitude only). Use F = 144…

Q: 5.52 Find the maximum load P that can be supported by the tripod if the force ssuny leg is limited…

A: Maximum value of load P??

Question

By three-moment equation, determine the moment at support B (in kN-m, magnitude only). Use F = 120 kN, P = 118 kN, w = 46 kN/m, a = 4 meters. Supports A, B, and C are simple supports.
ROUND OFF TO TWO DECIMAL PLACES.
W
F
P
A
В
a
a/3 a/3 а/3

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the support forces and draw shear force diagram and bending force diagram L1=6m, L2= 5m a=2m, b=2m, c= 1m, d= 2m F= 10 Kn, P= 3 kN/m
by three moment equation, determine the moment at support B (in kN, magnitude only). use F=120kN, w=48kN/m, a=3m.. supports A, B, and C are simple supports.
Using portal method, Calculate for the shear force in kN at member FC a = 12.6 kN, b = 27.2 kN, c = 3.5 m, d = 5.0 m, e = 5.4 m
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
Compute the magnitude (kN) and type (compression or tension) of the force member OG, PQ, HP, FG, GH, and OP.
A overhang beam hanged at B(6m) has two loads of 8 & 4 kn at 6 and 9 m. Calulate its moment using castigliano's theorem.
vertical triangular plate with base horizontal and 3.6 m high is submerged in water. The distance between the center of gravity and the center of pressure is 20 cm. If the total force acting on one side of the triangle is 79.46 kN, find the base width of the triangle.
If the resultant force acting on the support is to be1200 lb, directed horizontally to the right, determine theforce F in rope A and the corresponding angle θ.
If the beam is subjected to an internal moment of M = 40 kN . m, determine theresultant force caused by the bending stress distribution acting on the top flange A.
For the beam and loading shown below (L = 2.4 m, E = 200 GPa, I = 1000 mm4 and w = 30 kN/m), find (a) TThe slope at point D.(b) The reaction force at end A
Determine the moment equation for section AB. What is the bending moment (in kN-m) at x = 2.35 m? Determine the shear equation for section BC. What is the shear force (in kN) at x =8.15 m?
For the beam shown, determine the moment capacity in kNm of the beam at the endspan (supports) if ?? = 420 ??? and ??′ = 28 ???.