C-2 A uniform live load of 300 lb/ft and a single live concentrated force of 1500 lb are to be placed on the beam. The beam has a weight of 150 lb/ft. Determine (a) the maximum vertical reaction at support A, and (b) the maximum negative moment at A. Assume the support at A is a pin and B is a roller. 9ft A 9ft 9 ft. B

C-2 A uniform live load of 300 lb/ft and a single live concentrated force of 1500 lb are to be placed on the beam. The beam has a weight of 150 lb/ft. Determine (a) the maximum vertical reaction at support A, and (b) the maximum negative moment at A. Assume the support at A is a pin and B is a roller. 9ft A 9ft 9 ft. B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

BEAM ABC is fixed at both ends (A&C) and hinge supported at B. AB=6m (3I) BC=5m (2I), the beam carries a uniform load of 8KN/m from A-B and concentrated load of 36KN 3m from C. Use moment distribution method (1cycle) Determine the moment at A
The trolley rolls at C and D along the bottom and top flange of beam AB. Determine the absolute maximum moment developed in the beam if the load supported by the trolley is 2 k. Assume the support at A is a pin and at B a roller.
6. 28 A uniform live load of 2 k/ft and a single concentrated live force of 6 k are placed on the floor beams.If the beams also support a uniform dead load of 350 lb/ft, determine (a) the maximum positive shear in panel CD ofthe girder and (b) the maximum negative moment in the girder at D. Assume the support at C is a roller and E is a pin
When the 15KN/m load is applied to the three-member frame the support at D settles 10mm. Determine the moment acting at each of the fixed support A, C and D. The members are pin connected at B. E = 200GPa, and I = 800(10^6)mm^4.
The beam is loaded with uniformly varying load O at point D and maximum of 7kN/m at the fixed support. (a)Determine the horizontal reaction at the fixed support. (b)Determine the resulting moment at the fixed support. (c)Determine the vertical component of the reaction at support A.
1. Draw the influence line for member FC. Use the tabulation method. 2. A uniform live load of 10kn/m and a single live concentrated force of 35kn are to be placed on the beam. The beam has a weight of 38kn/m. Determine (a) the maximum vertical reaction at support B, and (b) the maximum negative moment at point B. Assume the support at A is a pin and B is a roller.
Determine the forces in cables AC and AB neededto hold the 20-kg ball D in equilibrium. Take F = 300 N andd = 1 m.
The beam is subjected to a uniform dead load of 1.2 kN/m and a single live load of 40 kN. Determine (a) the maximum moment created by these loads at C, and (b) the maximum positive shear at C. Assume A is a pin, and B is a roller.
For the cantilever beam loaded as shown. (a)Determine the vertical reaction at A. (b)Determine the shear at C. (c)Determine the maximum moment in KN.m
A uniform live load of 2 k/ft and a single concentrated live force of 6 k are placed on the floor beams. If the beams also support a uniform dead load of 350 lb/ft, determine (a) the maximum positive shear in panel CD of the girder and (b) the maximum negative moment in the girder at D. Assume the support at C is a roller and E is a pin.
The beam ABC is to be loaded with a 300 lb/ft uniform distributed live load so it causes the largest moment at point A. Calculate the value of the maximum moment. Assume the support at A is fixed, B is pinned and C is a roller.
The beam is subjected to a uniform dead load of 1.2 kN/m and a single live load of 40 kN. Determine (a) the maximum moment created by these loads at C, and (b) the maximum positive shear at C. Assume A is a pin and B is a roller. SHOW THE COMPLETE SOLUTION