Can someone please help me to answer the following question and draw all free body diagrams and equivalent load diagrams. 3. For the structure shown below, calculate the force in cable BC and the reactions at pin A.30° B200N/m3 mㅏ4 m-4.5 m[100 N

Answered: C 30° 3 m 4 m B 98 200 N/m 100 N

Engineering

Mechanical Engineering

C 30° 3 m 4 m B 98 200 N/m 100 N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.39P: The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables...

See similar textbooks

Related questions

Q: b) Outline the differences between Fig. Q4(i) and Fig. Q4(ii). Fig. Q4(i) Fig. Q4(ii)

A: Given: There are two figures in which figure 1 consists of the body and chasis of a car and in…

Q: Water is the working fluid in a reheat-regenerative Rankine cycle with one closed feedwater heater…

A: Given Power output=1.5x109Btu/hr To=60oFPo=14.7 lbf/in2 To find: a. the mass flow rate of steam…

Q: In the figure below, a member is subjected to an axial force P. If the cross sectional area of the…

Q: 13 L L 3 P L 3 (W₂+ W₁) L/2 WIL L 3 2P 2P L 3 A free body diagram of a horizontal beam on the soil…

A: Draw free body diagram and choose correct one.

Q: Water is the working fluid in a Rankine cycle. Steam exits the steam generator at 1500 lbf/in.² and…

A: Given data: steam exits the steam generators P5=1500 lbf/in2 and T5= 1100°FThe pressure and…

Q: Find the equivalent resultant force-couple system acting at point A. Show solution. Answers: R =…

A: Given

Q: Water is the working fluid in an ideal Rankine cycle. Steam enters the turbine at 1400 lb/in² and…

Q: Water is the working fluid in an ideal regenerative Rankine cycle with one closed feedwater heater.…

Q: Water is the working fluid in an ideal Rankine cycle. Steam enters the turbine at 1400 lb/in² and…

Q: A-C line Liquid R-134a A rigid container containing 6.6 kg of saturated liquid R-134a at 24°C is…

Q: Q3: A steel rod is rigidly attached between an aluminum rod and a bronze rod as shown. Axial loads…

A: GIven data Stress in steel = 140 MPa Stress in aluminium= 90 MPa Stress in bronze = 100 MPa Find…

Q: Find the sum of the vertical forces in pounds if F1 = 30 lb at 60 deg N of W and 50 lb at 40 deg S…

Q: ✪✪ PBC ANARva. 14 mm gusset plate 75 x 75 x 13 mm 75 x 75 x 6 mm 4 m C 96 kN 4 m E 6 m 200 kN 4 m F…

A: given data allowable stresses of τ= 70 MPa and σb= 140 MPa 22-mm diameter rivets ABC = 864mm2; ABE =…

Q: Water flows through a horizontal pipe at a rate of 4 liter/s. The pipe consists of two sections of…

Q: Define Arc welding.

A: The welding is a fabrication process. It is used to join metals and thermoplastic using the heat and…

Q: Water is the working fluid in an ideal regenerative Rankine cycle with one open feedwater heater.…

Q: Construct the three principal views from the given isometric view. The object is symmetrical about…

A: Given: Construct the orthographic projections from given isometric view.

Q: Water is the working fluid in an ideal Rankine cycle. Steam enters the turbine at 1400 lb/in² and…

A: The enthalpy of the steam at the inlet of the turbine corresponding to a pressure of 1400 lbf/in2…

Q: Consider a low-speed subsonic wind tunnel with a 12/1 contraction area ratio for the nozzle. If the…

Q: HEAT TRANSFER A 30 ft. long and 2 inch nominal diameter and outside diameter of 2.375 in pipe is…

Q: As shown in the figure, air with a volumetric flow rate of 17,000 ft/min enters an air-handling unit…

A: Given: The volumetric flow rate of entering air, Q = 17000 ft³/min The temperature of entering air,…

Q: Sketch the internal shear and moment as a function of the beam length (triangle denotes a pin…

Q: A 4ft- 5000 Ib 10ft B с

Q: PROBLEM 4.36 Calculate the reaction at each support for the truss shown Neglect the weight of the…

Q: An electric motor drives a large air conditioner in a temperature controlled laboratory which…

A: introduction; air conditioning used for controlling the moisture of air and temperature of the room.

Q: Find the sum of the horizontal forces in Newton if F1 = 100 N at 30 deg N of E and F2 = 80 N at 45…

A: Given Data: Force F1=100 N at 30° North of East. Force F2=80 N at 45° North of West.

Q: ankine cycle with reheat uses water as the working fluid. As shown in the figure below, the…

Q: The figure shows a control bar, subjected to a force of 90N. Since the length of the bar is 225 mm…

A: GivenF=90NL=225mm=0.225mMB=13.5 Nm clockwiseα=?

Q: Refer to the figure below and compute for the moment of force at point C -- (CW+) Mc YA FA = 600 N…

A: Given Data- A system of force given we have to find moment about C

Q: 141 litres of water flows through a pipe of 0. 3 m diameter per second. The average flow velocity in…

A: Given data:- Flow rate(Q) = 141 L/s = 0.141 m3/s Diameter of pipe(D) = 0.3 m The average flow…

Q: a 50 cm, 1.5 m cylindrical closed tank of pure water initially at 120 psia and 450°F. If the system…

Q: ystems 20 The beam shown carries vertical concentrated loads. Calculate the reaction at each…

Q: Find the magnitude and direction of the resultant force if F1 = 60 N at 45 deg N of W and F2 = 50 N…

Q: Water is the working fluid in an ideal Rankine cycle. Steam enters the turbine at 1400 lb;/in² and…

Q: Why are composites used in engineering?

A: introduction; composite are made by mixing of two or more different material. these material have…

Q: 2. For the joint shown in the figure, calculate: (a) The largest bearing stress between the pin and…

Q: 169.39 N 400 N a C 169.39 N X d a A 500 N 500 N B 400 N Determine angle a knowing that the…

A: Find the angle for triangular to be in equilibrium

Q: Composit wall K1=10.K2=30,K3=40 W/mC at sieries repectivelly.Thickness for al three layer are…

Q: A force of F = 22i is applied to the end of a rod extending from the origin (xo, Yo) (0, 0) meters…

Q: A semicircular plate with radius r = 2 is submerged in water as seen in the picture. Using the facts…

Q: An ideal Rankine cycle with reheat uses water as the working fluid. As shown in the figure below,…

Q: Water is the working fluid in an ideal regenerative Rankine cycle with one closed feedwater heater.…

Q: A certain polymer sample can be represented by a single Maxwell element that is composed of a…

Q: b) Outline the differences between Fig. Q4(i) and Fig. Q4(ii). Fig. Q4(i) Fig. Q4(ii)

A: As there are Two Types of Manufacturing Processes. 1.Additive Manufacturing( Adding the material)…

Q: Water is the working fluid in a regenerative Rankine cycle with one closed feedwater heater. Steam…

Q: The Poisson's ratio, u of common engineering materials lies in the range: 0 0 < μ ≤ 1.2 0 0 <μ <0.5…

Q: The flywheel shown has an angular velocity of 600 rpm. The connecting rod AB slides through the…

Q: An ideal gas is 45 psia and 80˚F is heated in a closed container to 130˚F. What is the final…

A: Given data P1= 45 psia and T1= 80°F Find the final pressure at 130°F

Q: Determine the velocity of the cylinder A when t=4s if the system is released from rest. Cylinder A…

A: Given Data: Mass of cylinder A mA=8 kg Mass of cylinder B mB=6 kg

Q: 7- Illustrates a composite wall. The wall is composed of two materials (A with kA = 1 W/m-K and B…

Concept explainers

Bending Moment

In general, we can define the bending moment as the reaction induced when a certain amount of load or force is applied to an element which makes it bend.

Question

Can someone please help me to answer the following question and draw all free body diagrams and equivalent load diagrams.

3. For the structure shown below, calculate the force in cable BC and the reactions at pin A.
30° B
200N/m
3 m
ㅏ
4 m
-4.5 m
[100 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What would be the maximum weight W of the block, shown in the following figure, so that the tension developed in any cable does not exceed 100 N
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure. Find the Dy and Dx modulus. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 9,4 kN. Angle α = 31 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
Find the support reacions and joint force of the construction shown on the figure, if; P=12 kN q=9 kN/m M=12 kN and L=2 m
Assume all four objects attached to a string of length L are in equilibrium in the above figure.Determine the tension in each section of string in terms of θ1, m, and g.
A uniform drawbridge must be held at a 38.5 ∘ angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45000 N, is 13.0 m long, and pivots about a hinge at its lower end. A cable is connected 3.80 m from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. a) What is the tension in the cable? b) Find the magnitude of the force the hinge exerts on the bridge. Find the direction of the force the hinge exerts on the bridge. c) If the cable suddenly breaks, what is the initial angular acceleration of the bridge?
SITUATION 7: Three forces P1, P2, and P3 are acting on a semi-circular structure as shown in Fig. THA-33. Support at A is hinge and support at B is roller. Given: a = 1 m; P1 = 1.8 kN; P2 = 0.9 kN; P3 = 0.45 kN; θ = 30⁰; β = 45⁰. Calculate the resultant of the three forces (in kN). (Answer: 2.45) Calculate the vertical reaction at B (kN). (Answer: 1.06) Calculate the reaction at A. (Answer: 1.63)
Two smooth spheres of weight W and radius r each are in equilibrium in a horizontal channel of A and B vertical sides as shown in the figure. Find the force exerted by each sphere on the other. Calculate these values, if r=250mm, b=900mm and W=100N.
Determine the tensions T1 and T2 in the strings required to maintain equilibrium for the suspended object weighs W = 48.7N shown in the figure. Take, α = 29.4° & β = 47.5°. a) The value of θ1 (Degree) = b) The value of θ2 (Degree) = c) The value of θ3 (Degree) = d) The value of Tension, T1 (N) = e) The value of Tension, T2 (N) =
The Figure shows a bar AB, of length L, which is supported at point A, against the wall andsuspended by a cable at point B, and a weight w is hung from it at end B. The weight of thebar AB and cable weight are negligible. Suppose the weight W and the angles θ1 and θ2are known. What is the direction of the reaction force R of the wall against the bar
A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0,respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the leftend where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) andthe weight (W) of the bar
Consider a w-N weight suspended by two wires as shown in the accompanying figure. If the magnitude of vector F2 is 100 N, find w and the magnitude of vector F1.