c) Critical track buckling force can be represented by the following equations. Pc = π²EI / (KL)² P is the critical buckling load L is the buckling length E = 210 kN/mm²; and I is the lateral moment of inertia, mm*) k = 0.5 If critical track buckling of track with potential buckling length of 20m is 12 tons, determine the minimum lateral moment of inertia of the rail to prevent track buckling.

c) Critical track buckling force can be represented by the following equations. Pc = π²EI / (KL)² P is the critical buckling load L is the buckling length E = 210 kN/mm²; and I is the lateral moment of inertia, mm*) k = 0.5 If critical track buckling of track with potential buckling length of 20m is 12 tons, determine the minimum lateral moment of inertia of the rail to prevent track buckling.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A block with mass m=(24+12)kg is pulled by a horizontal force P applied at point B in Fig.3. The coefficient of kinetic friction between the surfaces is we = (5A+5)/(25+94). When the acceleration of the block is a=(1+9)/4 m/s?, determine the cable forces Tax and Top- 0=(A+8) A=1
For the beam, why is the moment Mo negative? if i were to take the fixed point at A, Mo gives a smiling face which is the convention for positive. However, if i were to take the fixed point at B, Mo gives a sad face which is the convention of negative. So which fixed point should i take to determine the sign convention and why
CLO 2: A beam subjected to a uniformly-distributed load has a: fırst-degree shear curve zero-degree shear curve third-degree shear curve second-degree shear curve
Replace the loading by an equivalent resultant force and specify its location on the beam, measured from point A.
The figure below shows the reinforced concrete beam AB of a tourist lookout at the free end. Its weight per unit length is 2500N/m, and the beam rests on two pillars at A and B, with no fixed connection. A. Assuming the beam is uniform, which of the following gives the absolute maximum shear? i. 12500N ii. 10000N iii. 7500N iv. 22500N B. What is the value of the absolute maximum moment? i. 31250Nm ii. 20000Nm iii. 11250Nm iv. 22500Nm
Srart A crane supported by a jib is mobilized for demolition as it carries a wrecking ball of weight, W 42 kN. If angle alpha is 22 degrees, bus 1 B ents 21 3 Calculate the force the jib is subjected to due to the wrecking ball.
1) Consider the column below. If both sections are made of a steel with the Modulus of Elasticity of 200 GPA, calculate the stresses in both sections and the movements (displacements) of B and C. (Learning Activity: L06) 1 m 4 m 1.5 MN B 2 MN 1.5 MN 30 cm Cross Sectional Area BC: Hollow Circle with 2 cm thickness 60 cm Cross Sectional Area AB: Hollow Rectangle with 1 cm thickness 30 cm
Determine the magnitude and location of Resultant of the loading shown relative to the free end. 20 N/m EDN/m VON/m రెలి N
A uniform 50-kgf board rests on rough supports located at A and B in the figure. Thefriction coefficient μs=0.60 on both contact surfaces. If a man weighing 80 kgfpulls on the rope with a force of 40 kgf, determine:a) The angles "min" minimum and "max" maximum for which the system is in equilibrium.b) The minimum coefficient of friction that must exist between the soles of the man's shoes andthe soil for each of the cases in section a.
The 2.5-Mg car is being towed by a winch. If the winch exerts a force of T = 132.2(s + 1) N on the cable, where s is the displacement of the car in meters, determine the speed of the car in m/s when s = 11 m, starting from rest. Neglect rolling resistance of the car.
2. A uniform rectangular block is attached to a cart that is accelerating up a 20° incline at 3 m/s². The block is attached to a cart by a hinge at Point A and a roller at Point B. a. What is the force that the roller is applying to the block at Point B? b. What is the force that the hinge is applying to the block at Point A? Y a = 3 m/s² х 20° 0.8 m m= 100 kg B 0.6 m 1.0 m g