c. Figure 2.1 shows a rectangular plate 0.6 m wide and 1.2 m deep lying within a water body such that its plane is inclined at 45° to the horizontal and the top edge is 0.70 m below the water surface. Determine the total pressure force on one side of the plate and location of the centre of pressure. 45° 0.7 m h 0.6 m 1.2 m- ト Figure 2.1 0.6 m-

c. Figure 2.1 shows a rectangular plate 0.6 m wide and 1.2 m deep lying within a water body such that its plane is inclined at 45° to the horizontal and the top edge is 0.70 m below the water surface. Determine the total pressure force on one side of the plate and location of the centre of pressure. 45° 0.7 m h 0.6 m 1.2 m- ト Figure 2.1 0.6 m-

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter14: Lateral Earth Pressure

Section: Chapter Questions

Problem 14.18CTP

See similar textbooks

Similar questions

45.) A retaining wall supports a horizontal backfill that is composed of two types of soil. First layer: 5.91 meters high, Unit weight of 17.26 kN/m3, coefficient of active pressure of 0.291 Second layer: 5.36 meters high, Unit weight of 18.85 kN/m3, coefficient of active pressure of 0.301 Determine the distance of the total active force measured from the bottom of the wall. Round off to three decimal places.
A retaining wall 8 m high supports a cohesionless soil having a dry density of 1600 kg/m^3, angle of shearing resistance is 33 degrees and void ratio of 0.68. The surface of the soil is horizontal and level with top of the wall. Neglect wall friction and use Rankine’s formula for active pressure of a cohesionless soil. Determine the value of earth thrust on the wall per meter length if the soil is dry. a. 121 kN b. 186 kN c. 148 kN d. 137 kN determine the value of earth thrust on the wall if water level is 3.5 m below the surface. a. 230 kN b. 250 kN c. 180 kN d. 210 kN find the height above the base of the wall where the thrust acts during the water logged condition. a. 3.50 m b. 2.67 m c. 1.75 m d. 2.25 m
A damn having a triangular section has a vertical face 24 m high and base 12 m wide. Use sg=2.4 a. determine the height of water that could rise on the vertical side of the dam so that the maximum intensity of pressure at the toe is twice the average pressure at the base. Neglect hydrostatic uplift. b. What is the shearing stress at the base?
A concrete gravity dam with a trapezoidal section is holding water as shown in the figure. A distance of 15 meters from the toe, a drain is located. The drain has a pressure due to uplift of zero and increasing uniformly to full hydrostatic at the heel. Upstream face 1H:5V, while downstream face is inclined 1H:2V. Which of the ff nearly gives the maximum foundation pressure on the base of the dam in kilopascal ? Assume 23.54 kN/m3 for the unit weight of concrete. a. 3114 b. 1095 c. 4115 d. 964 e. 680
A vertical, trapezoidal gate in the face of a dike is subjected to sea water pressure (s = 1.3) on one side. The upper edge is in the water surface and is 1.577 meters long. Two edges are vertical and measured 2.77 meters and 3.77 meters each. Determine the total pressure on the gate and the location of the center of pressure.
A retaining wall 6 m high supports cohesionless soil having a dry density of 1600 kg/m³, angle of resistance 32 and void ratio of 0.68. The surface of the soil is horizontal and level with the top of the wall. Neglecting wall friction and using Rankine’s formula for active pressure of a cohesionless soil. 1. Determine the nearest value of the total earth thrust on the wall in KN per lineal meter if the soil is dry. a. 73.1 b. 86.7 c. 62.4 d. 98.1 2. Find the nearest value of the thrust on the wall in KN per lineal meter if owing to inadequate drainage, it is waterlogged to a level of 3.5 m below the surface. a. 112 b. 171 c. 147 d. 153 3. Find at what height above the base of the wall the thrust acts during the waterlogged condition. a. 2.21 m b. 2.00 m c. 1.74 m d. 1.42 m
A masonry dam has a coefficient of permeability in the vertical and horizontal directions of Kz=4m/day and Kx=5m/day, respectively. The difference in the head is 18m and the distance between the base of the dam and the downstream water surface is 18m. Assume z=35m and width of dam = 40m. a. Determine the seepage flow (m3/day) b Determine the uplift pressure (kpa) at A. c. Determine the uplift force (x10^3 kN) acting in the dam. Assume that the uplift pressure under the dam varies uniformly.
The cross section of a braced cut supporting a sheet pile installation in a clay soil is shown in Figure 14.22. Given: H = 12 m, clay = 17.9 kN/m3, = 0, c = 75 kN/m2, and the center-to-center spacing of struts in plan view, s = 3 m. a. Using Pecks empirical pressure diagrams, draw the earth-pressure envelope. b. Determine the strut loads at levels A, B, and C.
Repeat Problem 10.12 for q = 700 kN/m2, B = 8 m, and z = 4 m. In this case, point A is located below the centerline under the strip load. 10.12 Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft. Determine the increase in vertical stress at point A located z = 21 ft below the surface. Given x = 28.8 ft. Figure 10.43
Hi, please calculate and plot the distrbution of passive pressure in front of the wall and active pressure behind the wall In Soil 1: cohesion, c =0 angle phi = 38 degrees bulk unit weight, Y = 18kN/m3 For Soil 2: cohesion, c =0 angle phi = 28 degrees bulk unit weight, Y(sat) = 20kN/m3
A. A concrete dam retaining water is show in the figure. If the specific weight of concrete is 23.5 KN/m^3. What is the total hydrostatic force? Find the resultant force. Find the factor of the safety against sliding if the coefficient of friction is 0.50. What is the factor of safety against overturning? Find the location of the resultant. Find the maximum intensity pressure. Determine the minimum intensity pressure.
A concrete dam is triangular in cross section and (30+0.314)m high from the horizontal base. If water reaches a depth of (27+0.314)m on the vertical face, what is the minimum length of the base of the dam such that the resultant will intersect the base within the middle third? What minimum coefficient of friction is required to prevent sliding ? Determine the pressure distribution along the base. If the uplift pressure varies from half full hydrostatic at the heel to zero at the toe.