Structural Theory Calculate the deflection at Point C, usingConjugate Beam Method and Virtual Work MethodAPEMB↑Ay2.4m=Ay (96)Ayty 055 kN/m(z= 113KN·( ½ x 55✓By - 119 KNX2.4m+2.4mHOOTEN+2.4m34.8) 100 + By =0DATE:x 55 x 4.8) ( (4.8) + 4.8) - 100 (2.4) ₂0

Data given Find: Deflection at C using : (a) Virtual work method (b) Conjugate beam method

Answered: Calculate the deflection at Point C,…

Engineering

Civil Engineering

Calculate the deflection at Point C, using Conjugate Beam Method and Virtual Work Method

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: On an inclined plane, the difference in elevation of points A and B is 10meters. Solve for the…

Q: can you please explain your calculations? Im not sure on how you got 2 for the first part

A: Given: The velocity distribution in the boundary layer is given by the expression: uU=1-exp-2×yδ The…

Q: W₂=2rad/s A V₂ 3" 8 B Figure 1 TO INFINITY 90° TO INFINITY V F

Q: Assume that the flexural rigidity of the beam is constant. Given: w=6w0 Determine the reaction at…

Q: 5. For the soil profile given below, assume that the primary consolidation settlement for the clay…

A: Consolidation of the soil is due to expulsion of pore water from the soil, due to this the volume of…

Q: Problems 9.2 A cross-over occurs between two parallel B.G. Tracks of same crossing number of 1 in 8½…

Q: y Determine the moment of inertia of the beam's cross-sectional area with respect to the x and…

Q: For a fully developed flow of water in a pipe having diameter 10cm, with velocity 0.2m/s and…

A: Given: For a fully developed flow of water in a pipe, The diameter of pipe, d = 10 cm = 0.1 m Water…

Q: A wide channel is 1m deep and has a velocity of flow, V, as 2.13 m/s. If a disturbance is caused, an…

A: Given: A wide channel is 1 m deep, y = 1 m. Velocity of flow, V = 2.13 m/s

Q: My book says the right answer was 90 kPa

A: Given data in question Unit weight of dry bark clay 18 kN/m3 Saturated unit weight 15 kN/m3 and 21…

Q: A 32-mm diameter by 3.5-m long steel rod (1) is stress free after being attached to rigid supports…

A: Given data in question Diameter 32mm Length 3.5 m Elasticity modulus 200 GPa Coefficient of thermal…

Q: A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi;…

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

Q: 3. (a) The tapered shaft is confined by the fixed supports at A and B. If a torque T is applied at…

Q: 1,0 m * 4 m * 5 m TINININININININ NINI NININIK Dry bark clay y =18 kN/m³ PVP V I 1 I I Sa Ysat =15…

Q: Q1. The beam supports a uniform dead load of 500 N/m and a single live concentrated force of 3000 N.…

A: Given Data Dead load = 500 N/m Concentrated Live load = 3000 N Find 1. Maximum positive moment…

Q: Explain it in a piece of paper please

A: Given: Required: Shear stress at wall

Q: A square footing is to be constructed as shown in the Figure below. The design load, Qdesign is…

Q: Bouyancy and Floatation A bodyweight of 25N and 15N when weighed under submerge conditions in liquid…

A: Given data- Two body weights 25 N & 15 N, Relative densities = 0.6 & 1.0 respectively, To…

Q: The average rainfall values over a catchment in three successive 2-hour intervals are 3, 5 and 2 cm,…

Q: B B Sketch the influence line for the shear at B. MB MB deflected shape MB MB deflected shape MB MB…

Q: A water treatment plant treating 100,000 gallons/day has discovered that their source water…

A: According to given data A water treatment plant treating 100,000 gallons/day has discovered that…

Q: Lan dius of the curve is 4 times its tangent distance, determine the following using chord asis. a.…

A: According to given data The intersection of the two tangents of a simple curve forms an angle of…

Q: Classify the structure if statically determinate, statically indeterminate, or unstable. ROLLER…

Q: While testing a metallic rod, it is observed that the diameter of the rod is reduced by 0.0025 mm at…

A: Given : Reduced diameter = 0.0025 mm Axial pull = 20 kN Original diameter = 15 mm Modulus of…

Q: A vehicle was stopped in two seconds by fully jamming the breaks. The skid marks measured 9.8…

Q: What is the length in stations for a symmetrical vertical curve with an entering grade of +5% which…

Q: 4. Use the manning's equation above to find the streamflow rate (Q) under the following conditions:…

A: Manning's Equation: Manning's equation is used to determine the velocity of the flow of the water…

Q: If the elevation of BM-A is 975.00', what is the elevation of TBM-1? ENATAL 7.45 BS FS 5.12 6.77 BS…

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

Q: 10f2 A toft etermine the vertical displacement of Joint C A = 0.5 in² E = 29 #10³ ksi F BO 4K 10 ft…

Q: Follow IS code A reinforced concrete beam has a width of 300 mm and an effective depth to tension…

A: A ) Given data : Width of beam = 300 mm Effective depth = 600 mm f'c = 30 MPa and fy = 414 MPa…

Q: Which of the following that is not described for wind loads? * When structures block the flow of…

A: Wind load is a special kind of load on buildings, as it is actually capable of creating many types…

Q: The time required for a 50% consolidation of a 25mm thick layer drained both sides is 2 min 20…

A: Given: For 50% consolidation of a 25 mm thick layer having drainage both side , time required is…

Q: Problem 31: Determine maximum slope and maximum deflection for a simply supported beam of span 6m,…

A: First we summarise the given data : Span = 6 m point load = 60 kN To Find : Determine the max.…

Q: 6. Details of a retaining wall are shown in the figure below. The unit weight of the wall 2/3 to…

Q: Topic: MOMENT DISTRIBUTION METHOD Question: draw and completely compute the shear diagram and the…

Q: Design a concrete mix to implement a concrete slab (exposed to sever conditions moisture and…

A: Given, f'c = 30 MPa S = 4 MPa FM = 2.4

Q: What is the Demand-to-Capacity ratio of the W100x19.3 A36 Beam? The beam is not laterally supported.…

A: Properties of W100x19.3

Q: rectangular footing 1 m x 2 m is placed at a depth of 2 m in a saturated cla

A: Given data: Footing size = 1m x 2m. Depth = 2m. Unconfined compressive strength = 100 kN/m2. We…

Q: Consider a gated-controlled overflow spillway with a length of 30 ft and designed for a head of 8…

A: According to given data A gated-controlled overflow spillway with a length of 30 ft and designed…

Q: 16.1 A continuous footing is shown in Figure 16.18. Using Terzaghi's bearing-capacity factors,…

Q: 500 N a P O a = 15.150 O a = 48.150 O a = 37.150 O a = 29.150 O a = 53.150 10 cm N=0 (@pt of…

Q: There are three commonly used methods to calculate the point bearine capacity of pilfoundations in…

A: Pile foundation is a kind of deep foundation. In this method, columns, made of materials such as…

Q: A community plan to construct a concrete rectangular channel to pass 10 m³/sec on a slope of 0.003…

A: This question is from Open Channel Flow.

Q: The reaction at C lb.

A: Given data : A problem of structure.

Q: A cylindrical tank contains air, oil, and water, as shown in the figure. The air h pressure P=9 psi.…

Q: b) As shown in the figure below, a rectangular footing (B x L = 2m x 2.2m) is subjected to a…

Q: calculate the max deflection of the beam at the center

A: This question is from Strength of materials.

Q: The tank shown in the Figure is fabricated from steel plates with a thickness of "t". Derive the…

Question

Structural Theory

Calculate the deflection at Point C, using
Conjugate Beam Method and Virtual Work Method
A
PEMB
↑
Ay
2.4m
=
Ay (96)
Ay
ty 0
55 kN/m
(z
= 113KN
·( ½ x 55
✓
By - 119 KN
X
2.4m+
2.4m
HOOTEN
+2.4m
3
4.8) 100 + By =0
DATE:
x 55 x 4.8) ( (4.8) + 4.8) - 100 (2.4) ₂0

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the deflection at point B using virtual work method.W = 6.0 kN/m , P = 12.6 kN, a = 1.5m, b = 1.5m, c=1.3mNote: (input the sign)
Determine the slope at B and the deflection at C by the moment-area method for the beam shown below. Take ? = 29000 ?/??^2and ? = 2500 ??^4.
1)Determine the slope and deflection at point “C” using Virtual work methodE = 29000 ksi, A= 3500 in⁴
Using Virtual work method on Determinate frames, determine the horizontal deflection and slope at point C if EI= 400,000 kNm^2
Using Area-Moment Method, determine the deflection at the overhanging end in mm. Given: P = 4.2kN , w = 8.6 kN/m , a = 1.6m , b = 1.2m , c = 0.7m , E = 10 GPa , I = 20x106 mm4
Using virtual work method, E = 29 x 10^3 ksi, I = 500 in^4. Determine the deflection and slope at point B of the cantilever beam.
Use virtual work method to determin the deflection and slope at point B. EI= constant, E= 200 gpa, I=1200x10^6
Compute the vertical and horizontal deflections of B by the virtual work method. GivenE=200GPa and I=108mm4 .
Compute the vertical and horizontal deflections of B by the virtual work method. Given E=200GPa and I=108mm4 .
Using DIM (Double Integration Method), calculate the maximum deflection if EI = 400 000 kNm^2
Determine the slope at A in radian. Using Moment Area Method. Let P =38 kN. EI = 14220 kNm^2 Round off the final answer to three decimal places.
How many equations from the superposition table are required to determine the deflection at B?