Calculate the heat losses per unit length in a horizontal tube with an outside diameter of 15 cm, if its surface is kept at 400 K AND the surrounding air has a temperature of 300 K and a pressure of 1 bar. The properties of air at a pressure of 1 bar and a film temperature of 350 K are: In this case, v = 20.76 x 10-6 m2/s , α = 0.2983 x 10-4 m2/s, k = 0.03003 W/mK, Pr = 0.697, β = 2.86 x 10-3 K-1

Calculate the heat losses per unit length in a horizontal tube with an outside diameter of 15 cm, if its surface is kept at 400 K AND the surrounding air has a temperature of 300 K and a pressure of 1 bar. The properties of air at a pressure of 1 bar and a film temperature of 350 K are: In this case, v = 20.76 x 10-6 m2/s , α = 0.2983 x 10-4 m2/s, k = 0.03003 W/mK, Pr = 0.697, β = 2.86 x 10-3 K-1

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.37P

See similar textbooks

Similar questions

The interior of a refrigerator whose dimensions are 0.05 x 0.05 dam base area and 1.25 m high, must be kept at 4 °C. The refrigerator walls are constructed of two steel sheets (k= 35 kcal/h.m.°C) 3 mm thick, with 65 mm of material insulation (k=0.213 kcal/h.m.°C) between them. The film coefficient of the inner surface is 10 kcal/h.m².°C, while on the external surface it varies from 8 to 12.5 kcal/h.m².°C. Calculate: a) The power (in HP) of the refrigerator motor so that the heat flux removed from the inside the refrigerator maintain the specified temperature, in a kitchen whose temperature can vary from 21 to 36 °C; b) The temperatures of the inner and outer surfaces of the wall. Given 1 HP = 641.2 Kcal/h
The author and his then 6-year-old son have conducted the following experiment to determine the thermal conductivity of a hot dog. They first boiled water in a large pan and measured the temperature of the boiling water to be 94°C, which is not surprising, since they live at an elevation of about 1650 m in Reno, Nevada. They then took a hot dog that is 12.5 cm long and 2.2 cm in diameter and inserted a thermocouple into the midpoint of the hot dog and another thermocouple just under the skin. They waited until both thermocouples read 20°C, which is the ambient temperature. They then dropped the hot dog into boiling water and observed the changes in both temperatures. Exactly 2 min after the hot dog was dropped into the boiling water, they recorded the center and the surface temperatures to be 59°C and 88°C, respectively. The density of the hot dog can be taken to be 980 kg/m3, which is slightly less than the density of water, since the hot dog was observed to be floating in water while…
Hot water is being transported in a horizontal pipe (k = 0.15 W/m∙K, Di = 2.5 cm, Do = 4.5 cm), where the pipe inner surface temperature is at 100°C. A length of 2 m of the pipe outer surface is exposed to cool air at 12°C. Assuming that the properties of air can be evaluated at 40°C and 1 atm pressure, determine the outer surface temperature of the pipe. Is 40°C an appropriate film temperature for evaluation of the air properties?
A long steel rod 0.305 m in diameter is initially at a temperature of 588 K. It is immersed in an oil bath maintained at 311 K. The surface convective coefficient is 125 W/m2 -K. Calculate the temperature at the center of the rod after 1 h. The average physical properties of the steel are k = 38 W/m-K and α = 0.0381 m2/h.
To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (ks= 40 W/m·K) has an inside diameter of Di, 1= 150 mm and wall thickness ti= 20 mm while the outer steel pipe has an inside diameter of Di, 2= 250 mm and wall thickness to=ti. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (kp= 0.0675 W/m·K) between the two pipes does not exceed its maximum service temperature of Tp, max= 70°C. The ocean water is at ∞ T∞, o= -5°C and provides an external convection heat transfer coefficient of ho= 500 W/m2·K. The convection coefficient associated with the flowing crude oil is hi= 450 W/m2·K. (2) It is proposed to enhance the performance of the…
To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (ks= 40 W/m·K) has an inside diameter of Di, 1= 150 mm and wall thickness ti= 20 mm while the outer steel pipe has an inside diameter of Di, 2= 250 mm and wall thickness to=ti. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (kp= 0.0675 W/m·K) between the two pipes does not exceed its maximum service temperature of Tp, max= 70°C. The ocean water is at ∞ T∞, o= -5°C and provides an external convection heat transfer coefficient of ho= 500 W/m2·K. The convection coefficient associated with the flowing crude oil is hi= 450 W/m2·K. (2) It is proposed to enhance the performance of the…
To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe ( ks = 40 W/m·K) has an inside diameter of Di,1 = 150 mm and wall thickness ti = 20 mm while the outer steel pipe has an inside diameter of Di,1 = 250 mm and wall thickness . Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation ( kp = 0.0425 W/m·K) provides an external convection heat transfer coefficient of ho = 500 W/m2·K. The convection coefficient associated with the flowing crude oil is hi = 450 W/m2·K. (2) It is proposed to enhance the performance of the pipe-in-pipe device by replacing a thin ( ta =10 mm) section of polyurethane located at the outside of the inner pipe with an…
Water as much as 0.002kg/s at a temperature of 18 °C Flows into a tube with a flow that has been formed hydrodynamically. The inside diameter of the pipe is 1.5 cm and the surface temperature in the pipe is uniform at 125°C. Calculate the length of the pipe required to heat the water to become 82 °C
The cylinders that come out of the heat treatment furnace are cooled in a stagnant air environment in a horizontal position. The cylinders have a diameter of 100 mm and a length of 0.1 m. The temperature of the cylinders is 440 ° C and the ambient temperature is 20 ° C. Calculate the heat transfer from 10 cylinders to the environment. a) 3125 W b) 2350 W C) 1848 W d) 1354 W e) 2750 W
Water at 10C temperature flowing from a pipe with a diameter of 100mm at a speed of 2m / s, air from a pressure of 2 ATM at 180F flowing at a speed of 50 ft / s from a pipe with a diameter of 2 in, and an oil with a specific gravity of 0.78 and a diameter of 20 cp at a speed of 5 ft / s through a 2in pipe. Shows the flow state of the biopolymer melt flowing through the pipeline at a speed of 0.2 m/s, with a density of 900 kg/m3 and a density of 1 Pa-s
How is storage modulus and loss modulus relate with diffussivity of a drug molecule pass through a gel? Does higher storage modulus means lower difussivity?
Water at 1500 kg/h and 10°C enters a 10-mmdiameter smooth tube whose wall temperature is maintained at 49°C. Calculate (a) the tube length necessary to heat the water to 40°C, and (b) the water outlet temperature if the tube length is doubled. Assume average water properties to be the same as in (a).