Calculate the maximum shear force in the welds and the required weld size in the given figure. Where P= 50kN X=60mm, Y=150mm, Z=100mm What is the maximum force on the weld in kN/mm? (2 decimal places) What is the required weld size considering E70xx fillet weld in mm? (rounded value)

Calculate the maximum shear force in the welds and the required weld size in the given figure. Where P= 50kN X=60mm, Y=150mm, Z=100mm What is the maximum force on the weld in kN/mm? (2 decimal places) What is the required weld size considering E70xx fillet weld in mm? (rounded value)

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.4.2P: Use an elastic analysis and determine the maximum load in the weld (in kips per inch of length).

See similar textbooks

Related questions

Q: For the beam and loading shown, E-12 GPa, 1 - 20x10-6 m4. What is the vertical reaction at C in KN?…

A: E = 12 GPaI = 20 × 10-6 m4 Determine the vertical reaction at C using Area-Moment method.

Q: 10" 5" 5" 24 8" 10 # 8 bars 16" 3" 3" 3" 26" Normal Weight Concrete f'c = 7000 psi Gr. 75 steel…

Q: Question 8 A survey is performed on a closed traverse as shown in the Figure below. Assume line AB…

A: A closed traverse ABCDEFA as shown in the figure.Where,Also,FB of AB (True east).To find: Azimuth…

Q: Hydrostatic force on submerged bodies When a hydrometer as shown having a stem diameter of 0.30 in.…

Q: Please make a step by step procedure on how to calculate the maximum shearing stress experienced by…

A: Bolted connections are frequently used in structural design and engineering to provide structural…

Q: Challenge Problem 5) A proposed earthen dam will contain 6,000,000 yd^3 of earth. Soil to be taken…

Q: Mo ) TAT b B jº Find: Slope at ends and deflection at A using conjugate beam method.

Q: 2. Determine the shear and moment throughout the beam as functions of x. Draw the shear and bending…

A: Given:Required:Shear-moment equation and shear-moment diagram

Q: Calculate the ultimate moment capacity of a rectangular beam with b = 350 mm, d = 540 mm. As = 7x28…

A: The width of the beam is 350 mm.The depth of the beam is 540 mm.The diameter of the bar is 7-28…

Q: NOTE: This is a multi-part question. Once an answ Two members, each consisting of a straight and e…

Q: On Step 3 where do you get the sin(66.80)? reply asap.

A: Required:Explain sin(66.80) in step 3

Q: compute the maximum combined loads using the recommended ASD expressions from the AISC

A: D = 24 psfLr = 16 psfW = ± 42 psf

Q: Problem #2 The bar shown below has uniform cross section and material properties throughout. In…

Q: 3. The terminal velocity of descent V of a hemispherical parachute is found to depend on its…

A: We need to find out the pi terms using dimensional analysis

Q: Problem 3 For the frame shown with the given applied load, determine the vertical reaction at roller…

A: Given:Required:Vertical reaction at roller support A

Q: The floor system of a building consists of a 125 mm thick reinforced concrete slab resting on four…

A: Girder: - It is defined as the main supporting beam which carry vertical concentrated load.

Q: When a pressure of 2 * 10 ^4 * kN/(m ^ 2) is applied to 50 litres of a liquid, its volume is…

A: Pressure = 2 X 104 kN/m2Initial volume = 50 litersChange in volume = 0.5 litreTo Find :Bulk modulus…

Q: A milling operation was used to remove a portion of a solid bar of square cross section. Forces of…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitt Warren bridge…

Q: 0.3 m. 120° 60° 0.25 m

A: Angle made by the force with the x-axis, Angle made by the force with the y-axis, Angle made by the…

Q: The short column below is subjected to Pu = 100W kN. . Use f'c = 28 MPa and fy = 415 MPa, Clear…

A: Pu = 100 W kNf'c = 28 MPafy = 415 MPaTo Find :Max moment applied along x axis ?

Q: 4-10 Problem 4-10 The figure shows a cantilever consisting of steel angles size 100 × 100 × 12 mm…

A: Given data,steel angle size 100x100x12 mm mounted back to backcantilever beam is given…

Q: llowing the sieve analysis and the specific gravity of "SAND 1", a hydrometer test wa erformed on…

A: A hydrometer test is used to classify soils and determine their properties, such as their…

Q: Hydration of cement is exothermic process that generates heat. The table below shows the heat…

A: Option-a:This option implies that utilizing any of the specified cement components is unsuitable for…

Q: A rigid beam is supported by bar DE. If the vertical displacement of point D is to be less than 0.1…

A: Vertical displacement of point D (∆D) = 0.1 in. Determine the minimum cross sectional area of bar DE…

Q: A velocity field is given below. Find the stream and velocity potential functions corresponding to…

A: Given Velocity functionTo find out Stream function Potential function

Q: A 240-N force is applied as shown to the bracket ABC. Determine the moment of the force about A. 25…

Q: ermine the force in each member of the tri pression. Assume all members are pin co 3k 6k 6k 6 ft F 6…

Q: 4/15 Determine the forces in members BC and BG of the loaded truss. Ans. BC 3.46 kN C, BG= 1.528 kN…

Q: 1. From the given truss below, answer the following: 9 m G 4 m 135 kN 135 kN B 4 m C4m E Compute the…

Q: etermine the azimuths for the traverse below. AZAB, AZBC, AZCA.

Q: The following dissolved-oxygen values were found after 5 days of incubation in 305-mL BOD bottles:…

A: The dissolved-oxygen values you provided, 8.2, 8.0, and 8.1, were found in three blank samples after…

Q: Problem 8: Approximate Analysis for Vertical Loads

A: Performing an approximate analysis for vertical loads is a common practice in structural engineering…

Q: without rupturing. Determine the maximum length, 1, allowed if the roughn 00015 ft and the flowrate…

Q: Where it get the 300 here, the green circle

A: Consider the given formula.Here, is equal to half of the total depth of the beam.

Q: Compare and contrast the von Neumann architecture and Harvard architecture in computational systems.

A: The Harvard architecture and von Neumann architecture are two fundamental CPU (Central Processing…

Q: o Given: A tapered shaft with P, L, and E known and constant and h = d (1+z) P d X @Eric P. Kasper &…

Q: What are the possible reasons for making a new road that is connected to both end points of an…

A: 1. Traffic Diversion: Traffic congestion on existing roads can lead to delays, frustration, and…

Q: The force system consists of the force P = - 300⁰ + 2005 + 150k and the couple C. Determine the…

A: Given:P=-300i+200j+150kMoment about axis DE = 800 lb-ftRequired:Magnitude of couple C

Q: A 60 mi² drainage area has the following characteristics: longest flow path length of 10 mi, flow…

Q: The specific gravity of the solids is 2.70, pw= 1000kg/m³ and the volum the compaction mould is…

A: Maximum dry density :A style of residence that includes measures of strength, density, durability,…

Q: 24 KN m * 6m 14 KN m TET D 2m -pin V E F 72 KN B $5 * * * 2m 2m 2m 36 KN m

Q: draw shear and moment diagram Need only a handwritten solution only (not a typed one).

A: Draw the shear force and bending moment diagram of the beam.

Q: 2. Design the cantilever beam shown. Assume Grade 60 steel and f = 4500 psi. WD 1 kip/ft + weight of…

A: Grade 60 steelf'c=4500 psiLive load PL= 12 kipsDead Load wD= 1 kip/ft+Weight of beam

Q: As per plan, the distance between two telephone poles is 356.35 meters. If the location of one is…

A: Distance between two poles, Nominal tape length, Correction due incorrect tape length, Ground slope,…

Q: Calculate the soil's total unit weight in kN/m3 assuming a dry density of 1424 kg/m3 and a water…

A: Dry density = 1424 kg/m3 Water content (w) = 42% Determine the total unit weight of the soil in…

Q: o Given: A earth pile with L, E, and A known and constant F Y X (L-x) steel pile soil f =…

Q: Show that the discharge, Q, of a liquid of density, p, dynamic viscosity, μ, and surface tension, o,…

Q: PROBLEM 5.3: A simply supported beam 7m long supports a uniformly distributed factored load equal to…

Q: Design a building column made of A36 steel (fy-36 ksi) having length of 10ft using AISC table to…

A: Design procedure of Building column: The designing of any structural member always has more…

Concept explainers

Properties of Aluminium

Aluminum (or Aluminum) is a silvery-white in color metal. The chemical symbol of aluminum is Al and it has an atomic number (Z) of 13 in the periodic table. The aluminum name for this metal is derived from the Latin word ‘alumen’, which means bitter salt. Aluminum was discovered in the year 1825 by Hans Oersted, and later Friedrich Wöhler isolated aluminum. It is the most commonly found metal in the earth’s core, which is around 8% of the total core mass. Moreover, it is the third most commonly found element on earth after oxygen and silicon. Electron distribution of aluminum per shell is 2, 8, and 3 with a valency of 3. Atomic weight is nearly 26.9815 u.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction to question

VIEW

Step 2: calculation part

VIEW

Step 3: calculation part

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Assuming the thickness of the weld is 1 mm, calculate: 1.Moment of Inertia of every parts of weld sections 2.Global Centroid for the weld, assuming it is angle section. 3.Global Moment of Inertia with respect to Y and X axis respectively (Ix and Iy) . 4.The farthest distance of weld, Rmax. of weld subject to in-plane
The allowable unit stress in shear on a fillet weld is 15,000 psi, and the total actual length of the weld CANNOT exceed 3in. If the weld must transmit a total force equal to 9600 lb, it's size should be A. 1/2 in. B. 3/8 in. C. 5/16 in. D. 1/4 in.
Determine the required fillet weld size for the angle bracket shown per the given weld configuration to carry the given eccentric load. Use ASD.
What size of fillet welds are required to attach a 16 mm flat plate hanger to the bottom flange of a UB 457 x 152 x 74 so that the full tensile capacity of the hanger may be developed ? Calculate the effective width (beff) of the weld. Assume the use of S355 steel for UB and the plate and the width of the plate is the same as the flange width of UB .
Using the elastic method, determine the maximum force to be resisted per inch by the fillet weld shown in the accompanying illustration.
Find the Load Capacity of the weld if the throat thickness is 8. 13 mm, Nominal Tensile Strength, Fu = 520 MPa, and length of weld = 400 mm.
What is the safe strength of a 5/16 in. fillet weld if it's actual length is 3 1/2 in. and the allowable unit stress in shear is 13,600 psi? A. 8650 lb B. 9420 lb C. 10,500 lb D. 11,800 lb
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A WT bracket is connected to a wide flange column with an E. 70 fillet welds as shown in the figure with Pu = 380 KN acting at an eccentricity of 150 mm. Questions: a) Determine the average vertical force per unit length of weld. b) Determine the maximum force to be resisted by the fillet weld. c) Determine the size of the fillet weld appropriate to carry the load.
If the structural frame is replaced to structural steel and the connections is to be designed, determine the following Determine the centroid of the weld measured from the given origin A. Determine the direct shear load in the welds. Determine the required size of the fillet weld(E60xx) if the maximum resultant load is 750,000 N/mm
Show min weld strength (kips/in) of the nominal size of the fillet weld from 1/8" to ¾” with SMAW. Explain the effective area of the welds.
The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the weld CANNOT exceed 3 in. If the weld must transmit a total force equal 9600 lbs, its size should be
A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu = 483.33 MPa. Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. Determine the length of side fillet weld required at the heel. Determine the length of side fillet weld required at the toe.