Calculate the minimum distance, x so that the bracket can support the cylinder of any mass without slipping as shown in Figure Q2. Given, the coefficient of static friction at A is Hs= 0.4 and the collar at B is smooth so it only exerts a horizontal force on the pipe. Neglect the mass of the bracket. 100 mm B 200 mm

Calculate the minimum distance, x so that the bracket can support the cylinder of any mass without slipping as shown in Figure Q2. Given, the coefficient of static friction at A is Hs= 0.4 and the collar at B is smooth so it only exerts a horizontal force on the pipe. Neglect the mass of the bracket. 100 mm B 200 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.3P: Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair...

See similar textbooks

Similar questions

The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of static friction is s=12 between all contact surfaces. Determine the smallest force P that would prevent the wedge from sliding out.
The test specimen AB is placed in the grip of a tension-testing machine and secured with a wedge. The coefficient of static friction at both surfaces of the specimen is s. If the wedge angle is =18, determine the smallest s for which the grip is self-locking (no slipping takes place regardless of the magnitude of the force P). Neglect the weight of the wedge.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
Determine the smallest horizontal force P that must be applied to block B to cause impending motion. The angles of static friction are 15 between the blocks and 30 between the blocks and the ground.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
In the figure shown, the coefficient of friction is 0.25 for all surfaces of contact. Find the weight W if the 200N weight is on the point of moving (a) up; (b) down.