Calculate the power of solar radiation flux per m² for 2mmol/(m².s). where the wavelength is 900 nm. Avogadro's number 6.022 1023, Blanck's constant- 6.6* 10-34 Consume 2000m² of this solar radiation in power plant to find the total power input to consumer where the efficiency of power plant instruments and transmission lines (50%, 85%) respectively.

Calculate the power of solar radiation flux per m² for 2mmol/(m².s). where the wavelength is 900 nm. Avogadro's number 6.022 1023, Blanck's constant- 6.6* 10-34 Consume 2000m² of this solar radiation in power plant to find the total power input to consumer where the efficiency of power plant instruments and transmission lines (50%, 85%) respectively.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The PCB monopole antenna shown in figure below is required to be designed for Bluetooth Low Energy wireless mouse operating at 2.45 GHz. What should be the length of the antenna trace in mm. Assume the substrate of the PCB is foam (dielectric constant = 1)
A 350 km transmission line has the following parameters: z = 0.0195 +j0.35 Ω/km y = j4.5 μS/km If the load served by the line is 300 MVA, with an fp of 0.8(-), at a voltage of 100√3KV say: 6. The value of the incident and reflected wave, as well as the total voltage, at a point 200 km away from the extreme load. 7. The voltage and current at the emitting end. 8. What would be the percentage error in the magnitude of the voltage VS if it is calculated with the lossless line model? lossless line model? Note that the accurate value is the one that takes losses into account.
A 350 km transmission line has the following parameters: z = 0.0195 +j0.35 Ω/km y = j4.5 μS/km If the load served by the line is 300 MVA, with an fp of 0.8(-), at a voltage of 100√3KV say: 6. The value of the incident and reflected wave, as well as the total voltage, at a point 200 km from the end of the load. 7. The voltage and current at the emitting end. 8. What would be the percentage error in the magnitude of the voltage VS if it is calculated with the lossless line model? lossless line model? Note that the accurate value is the one that takes losses into account.
Consider a 10W power transmitter and a 30dB transmission antenna, the EIRP value will be: Select one or more than one: a. The value of the EIRP is: 10000watt b. The EIRP value is :50dBW c. The EIRP value is: 200 Watt d. The EIRP value is: 40dBw
A microwave link includes two sites that are 10 km apart and uses a center frequency of 9 GHz. On either transmitter or receiver side, a 100-m transmission line that has an attenuation per unit length of 0.01 dB/m is connected to an amplifier and a parabolic reflector antenna. Other losses caused by connectors and insertions incurred on one side amounts to 3 dB. Antenna has a power gain of 20 dB. If the output of the transmitter amplifier is 30 dBm, what is the received signal level (in dBm) at the input of the receiver amplifier?
"A transmission line with negligible attenuation has L = 0.1 uH/ft and C = 0.2 nF/ft and is typically operated at 100 MHz. What is the velocity of propagation (in 10^8 m/s) of the signal along this line? Enter only the numerical value. No need for the unit. Use four decimal places (if the answer is not an integer). For example, the calculated value is 3x10^8 m/s, then enter 3."
A cellular radio transmitter has a power output of 3 W at 800 MHz. It uses an antenna with a gain of 3 dBi. The receiver is 5 km away, with antenna gain of 12 dBi. Ignoring feedline losses and mismatch, calculate (a) the EIRP in dBW (b) the free space path loss, (c) the power delivered to the receiver in W and dBm
The height of base station is 200 meter and operated at 2600MHz. The gain of the base station antenna (transmitter) and the receiving antenna (mobile phone) are 20 dB and 6 dB, respectively. The distance between base station and mobile phone is 2 km. a) Find the free space transmission loss. b) Find the power received when the transmitted power is 60 W.
A 0.48520λ0 dipole antenna is made to work at 4 GHz. The antenna is then connected to a 12 V voltage source which has an internal resistance of 25 Ω) a) Make a diagram of the above system, b) Is an impedance matching circuit needed? If yes, where should the impedance circuit be inserted and make a diagram of the system with the adjusting circuit, c) How many cm is the length of the dipole antenna above, d) How much power is emitted when not using the adjusting circuit and e) How much power is emitted when using the adjusting circuit. Solve subparts D,E max 20 minutes ASAP
The following lossless network is powered by a f=9 GHz microwave source. A matching circuit is designed for ZL=91 load and ZS. Since it is known that L=631,30220884613 pH here, what is ZS? π=3.1416
Q. A base stationcellular communicationsystems lossless antenna has a maximum gain of 16 dB (above isotropic) at 1,900 MHz. Assuming the input power to the antenna is 8 watts, what is the maximum radiated power density (in watts/cm2 ) at a distance of 100 meters? This will determine the safe level for human exposure to electromagnetic radiation.
In an optical ﬁbre, the power drops by a factor of 10 approximately every 30 km. If the transmit power is 0.35 W, how far will a signal be transmitted before the power is attenuated to 350 μW? As part of your answer, include a table showing the signal power (in W) vs. distance in 30 km intervals