Calculate the tolerance if the maximum limit is 97.45 mm and the minimum limit is 96.99 mm.
Q: A nozzle is designed to accelerate the fluid from V₁ to V₂ in a linear fashion. That is, V = ax + b,…
A: Given data:- Velocity profile V= ax+ b, V1 = 10 m/s at x1 =0 and V2= 25 m/s at x2 = 1 m, To…
Q: In the figure below,the point mass m₂ glides without friction on horizontal plane, it is connected…
A:
Q: Question 12 of 12 The zero order reaction A- Products takes 63.5 minutes for the oncentration of A…
A: Given data, Zero Order Reaction t = 63.5 min No = 0.301 M ( No = Initial Concentration of A) Nt =…
Q: Find reactions and plot shear force and bending moment diagrams
A: This question is based on the concept of shear force and bending moment diagram.
Q: Explain how the properties and structure of different given engineering materials affect their…
A: High carbon steel is a type of steel alloy that has a carbon content of 0.6-1.5%. It is commonly…
Q: Single Stage Vapor Compression (SSVC) refrigeration system has a cooling capacity of 7.5 tons. The…
A:
Q: Where do the highest energy losses .3 take place in power plants using gas and steam turbines?…
A: Power plants use gas or steam turbines to convert one form of energy into another and ultimately…
Q: The motorcycle is traveling at 45 m/s when it is at A. The speed is then decreased at i-(0.058)…
A:
Q: Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square…
A: According to the data a structure is ABC is provided with the loading as shown in the figure We…
Q: Consider (Figure 1) with F₁ = 260 N and F2 = 170 N. Resolve F₁ into components along the u and…
A: Calculated components of F1 along the u and v axes in N.
Q: 3 ft us 4 ft < 1 of 1 B Determine the moment of the force F = {40i -35j + 20k} lb about the AB ax…
A:
Q: ᴀ ꜰᴀʀᴍᴇʀ ʜᴀꜱ ᴀ ꜱᴍᴀʟʟ ꜱᴛʀᴇᴀᴍ ᴏɴ ʜɪꜱ ᴘʀᴏᴘᴇʀᴛʏ ᴡʜɪᴄʜ ʜᴇ ᴛʜɪɴᴋꜱ ᴍɪɢʜᴛ ꜱᴜᴘᴘʟʏ ᴇɴᴏᴜɢʜ ᴘᴏᴡᴇʀ ᴛᴏ ꜱᴜᴘᴘʟʏ…
A:
Q: What is U3003:16 the diagnostic trouble code (DTC) for? What system component sets the U3003:16 DTC?…
A: Given: Vehcile- 2016 ND Mazda MX5
Q: (5). The compressor of an open-cycle gas turbine unit receives air at 100kPa, 18°C and delivers it…
A: The given information in the problem is shown in the following attached image:
Q: The total acceleration of a point on a rim of a 1.5-m diameter pulley is 9m/s2 when its angular…
A: For solution refer below images.
Q: A compressor takes in air at a pressure of 67 kN/m2 . The pressure of the air at exit from the…
A: Given data:- A compressor takes in air at a pressure (P1) =67 kN/m2The pressure of the air at exit…
Q: ● . In the US, how are the abilities of substances to cause cancer classified? are their…
A: To find: The abilities of substance to cause cancer classified, in the US.
Q: 2. Maximum quantity of heat What is the maximum quantity of heat that can be produced by burning…
A:
Q: CO2-eq emissions by .6 heating A house heated by an electrical radiator uses 8000 [kWh] electricity…
A: To find: The CO2-eq emissions. Given: The electricity consumption is 8000 kWh. The emission factor…
Q: For H₂O, determine the specified property at the indicated state. (a) T = 140°C, v = 0.5 m³/kg. Find…
A: As per bartleby guidelines we are allowed to solve only 3 parts of a question. So please post…
Q: 4. Sit in your chair with your arms at your side. Raise one arm out to your side so it is abducted…
A: Free-body diagram: A diagram of a system at which all forces are shown is called a free body diagram…
Q: At a hydro electric power plant site, available head and flow rate are 24.5 m and 10.1 m³/s…
A: Given: The available head H=24.5 m The volume flow rate Q=10.1 m3s The speed of turbine N=4…
Q: A ¼ inch thick steel plate has to be punched with a 1/2 inch holes by applying a force of 40 tons.…
A:
Q: Car B is towing car A at a constant speed of 10 m/s on an uphill grade when the brakes of car A are…
A: The mass of car A is ma=1400 kg. The mass of car B is mb=1200 kg. The velocity of car A and car B…
Q: ▼ For= ▼ Part A Reaction force at C'after the load has been applied Submit L. Find the magnitude of…
A: The values are P=2500 kN, e=0.35 m, d=0.65 m, a=1.9 mm The young modulus of elasticity of steel rod…
Q: Find the reactions for the rigid body below. A is a pin and I is a roller. N BCDE 2 kN F G H 2 kN 5…
A:
Q: Which of these propositions are right (multiple answers) a. A heat pump and a chiller works…
A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve the first three…
Q: 1. Determine the force in each member of the Gambrel roof truss shown. State whether each member is…
A:
Q: 5. What weight W is necessary to start the system of blocks shown in the figure moving to the right?…
A: The coefficient of friction is μ=0.1. The pulleys are frictionless.
Q: Problem 2. If a force of P = 100 N is applied to the handle of the toggle clamp, determine the…
A: Given data P= 100N Find the horizontal force on smooth wooden Block E
Q: Diesel fuel C₁2H23 being pump out of the tank going to the burner is burned with 10% excess air at a…
A: a. The complete actual combustion equation: C12H23 + (10% excess air)O2 -> CO2 + 12H2O b. The…
Q: Nitrogen gas at a stagnation temperature of 300 K and a static pressure of 2 bar flows adiabatically…
A: Given: Stagnation temperature of nitrogen gas St=300 K Static pressure of nitrogen sp=2 bar The…
Q: Take note: Please provide complete sketches and solution. A 1,000-N cylindrical tank rests on…
A:
Q: Suppose that F = 500 N in (Figure 1) and (Figure 2). Figure F 1 m B 2 of 2 In the case of (Figure…
A:
Q: A tank contains 20 kg of saturated liquid water at 75°C. What is the total internal energy of the…
A: Given that: The tank contains 20 kg of water. Water is at saturated liquid condition at 75°C. It is…
Q: Answer the following question 1. Give at least 6 examples of solid fuels 2. Identify and classify…
A: Fuels: Fuel is a substance that is burned to produce energy, typically in the form of heat or…
Q: Use blank or isometric grid paper to draw the isometric views of the following objects.
A: Find Draw an isometric view of the given object on the isometric grid paper.
Q: 2.11 A steel tank is to be positioned in an excavation. Knowing that a = 20°, determine by…
A: Givenα=20o
Q: Determine the magnitude and location of the resultant for the load systems shown with respect to…
A:
Q: Problem 5. Heat is generated uniformly at a rate of Se in a copper wire of radius re having thermal…
A:
Q: Name the Crystallographic Direction and Show the Steps
A: Given
Q: In a gas turbine plant the hot gases from the combustion chamber pass to the turbine where they are…
A: It is given that the gas power plant is working between two pressure p1 =100 kPa and p2 = 600 kPa…
Q: 3-2. The members of a truss are pin connected at joint O. Determine the magnitude of F₁ and its…
A:
Q: A quarter car model of an automotive vehicle suspension system is shown in Figure Q2 below, where k,…
A: According to the given data m1=378.9kg m2=23.4kg k1=19.3kN/m k2=94kN/m We need to find First…
Q: Problem 3 Determine the moment exerted by cable AD about point C. X 1 m 1m 0 D C 3 m FAD B = 100N A…
A: Given data Force in cable AD = 100N Find the moment of force about point C
Q: converted box board sample measures 1.625 ft (Length) by 1.5 ft (Width) with the flutes running…
A: Given data: Sample length before conversion = 1.625 ft Sample width before conversion = 1.5 ft…
Q: One kind of optical storage medium is the Direct View Storage Tube (DVST).
A: Introduction A direct view storage tube (DVST) employs an electron gun and phosphor-coated…
Q: Problem 6. The A-36 steel pipe has an outer radius of 20 mm and an inner radius of 15 mm. If it fits…
A: Given: The outer radius of pipe ro=20 mm=0.02 m The inner radius of pipe ri=15 mm=0.015 m Distance…
Q: We have refrigerant R-134a at a temperature of 30 C and a specific enthalpy of 127 kJ/kg. Find the…
A: According to the given data A refrigerant R-134a is at T= 30 C h=127 kJ/kg. we need to find The…
Q: A 12.5 mm thick steel plate is to be punched with 22.5 mm hole. It has an altitude shear stress of…
A:
Calculate the tolerance if the maximum limit is 97.45 mm and the minimum limit is 96.99 mm.
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 2 images
- Calculate the maximum limit if the tolerance is 0.004 cm and the minimum limit is 0.985 cm.1. Calculate the tolerances and allowances for a shaft with a diameter of 40 mm with a tolerance area k and a tolerance quality number 6, paired with a hole of the same diameter as the shaft and a tolerance area H with a tolerance quality 7. Also draw these tolerances schematically. ( answer in 20 minutes very needed thank u )Please write the definitions for tolerances, draw the hole shaft basis diagram. Write down different fits
- Tolerances for a hole and shaft assembly having a nominal size of 50 mm are as follows: Hole = 50 (+0.02 )/(+0.00 ) mm and Shaft = 50 (-0.05)/(-0.08) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.-write legibly and show complete solution-write the answers on 5 significant digits in mm^4Please help, the tolerance is 3%
- The following limits are specified in a limit system, to give a clearance fit between a hole and a shaft: Hole = 10 (+0.05 )/(-0.00 ) mm and Shaft = 10 (-0.003)/(-0.010) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.An engineer is using a machine to cut a flat square of Aerogel of area 144 sq. c.m. If there is a maximum error tolerance in the area of 8 sq. c.m., how accurately must the engineer cut on the side, assuming all sides have the same length? How do these numbers relate to δ, ε, a, and L?In the following figure, add the tolerance zone and limits of size for both parts.
