Calculate the use factor in decimal form for at least two decimal point of a power plant if the capacity factor is 35% and it operates 8000 hrs during the year? Calculate the use factor in decimalform for at least two decimal point of apower plant if the capacity factor is35% and it operates 8000 hrs duringthe year?

Solution: Given Data: t = 8000 hrs C = 0.35

Answered: Calculate the use factor in decimal…

Calculate the use factor in decimal form for at least two decimal point of a power plant if the capacity factor is 35% and it operates 8000 hrs during the year?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Related questions

Q: A room has to be maintained at 25 deg C at all times. Assuming the outside temperature of the room…

A: GivenT1=25oC=298KT2=-5oC=268KQ=42kW

Q: 1. Consider the following schematic of a power plant (operating in what is called a 'Rankine Cycle')…

A: Given data: Mass flow rate (m) =25 kg/s Write thermal property value at the corresponding points…

Q: 250-kW generator has an efficiency of 89.2 per cent when delivering one -half of rated load.…

A: Given Power of generator P=250 kW Efficiency of generator η=89.2 %

Q: A 2 MW diesel engine power plant provides power to users with a maximum demand of 1.4 MW and Load…

A: Solution: Given Data: W=2 MWWmax=1.4 MWLF=40%Ci=44 million bahtCm=4.2 million bahtD=10%O=8600 hr/yr

Q: 6. What is the total cost of using the following at 9¢ per kilowatthour? a. 110W TV set for 4 h b.…

Q: kJ/kg then the specific net work output of the cycle is

A: Given data; P1=100kPaT1=300 Kmep=1000kPaγ=1.4efficiency (η) =0.5R=0.287 KJ/Kgk we have to find net…

Q: Differentiate the following terms: a. Efficiency b. Capacity factor

A: Capacity factor is the fraction of the amount of actual energy generated in a given period, to that…

Q: A.) A power plant is said to have a plant use factor of 48.5% and a plant capacity factor of 42.4%.…

A: As per bartleby term and condition i upload solution of first question and i request you to kindly…

Q: A newly installed refrigeration system produces 250 Btu/lb of cooling Calculate the mass of…

Q: C3 (1) Energy source requirement comparison: nuclear power versus coal energy production consider a…

A: Given data, Capacity of the power plant, P = 4600 KW Coal calorific value, CVcoal = 29300 MJ/kg…

Q: A small steam turbine power plant of 5000 kw capacity has a full load steam rate of 6 kg steam per…

Q: A given power plant has the following data: 3.5MW average load 1,500 residence P10.20 kw-hr 67,500…

A: ◆ The maximum demand is 49,950 kW-hr. ◆ Hence, the correct answer is option (C).

Q: Quation 2 Siven According to figure 1, Given data as (COP)Hp =3.5, Q= 90000 KJ/h (rate) and 1KW =…

Q: A diesel engine in a power plant has an output of 2000 KW at 1000 rpm. It uses fuel oil having a…

Q: i. A Wind Generator with the following data is installed at a wind site. Power output from the…

Q: Justify that a change of load factor from 50% to 60% affects the cost of generation per unit by…

Q: QI:: A- The absolute pressure in water at a depth of 5 m is read to be 145 kPa. Determine the…

Q: A Diesel engine used in a diesel power plant with two- stroke has 14 cylinders and has a total…

Q: Express the result in %.

Q: he maximum thermal efficiency possible for a power cycle operating between 1200°F and 225°F is: The…

A: Given:T1=1200°FT2=225°F

Q: A given power plant has the following data: 3.5MW average load 1,500 residence P10.20 kw-hr 67,500…

Q: Consider a worker-machine system that consists of external manual work elements (E), machine work…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: A SYStem executes a power cycle while recieving 750 k) by heat transfer at a temperature of 1500°k…

A: GivenQ1=750kJT1=1500kQ2=-100kJT2=500KQ3=?T3=1000K

Q: house is maintained at 75 °F by a heat pump. The outside temperature is 20°F, and the heat loss is…

Q: A given power plant has the following data: 3.5MW average load 1,500 residence P10.20 kw-hr 67,500…

A: ◆ The maximum demand is 49,950 kW•hr. ◆ Therefore, the correct answer is option (C).

Q: Steam engine with incomplete expansion receives saturated steam at 1.04 Mpa, expands it to 0.105 Mpa…

A: Since you have posted a question with multiple sub-parts, and each subparts there are more than one…

Q: 11. Cost of a 20MW power plant in the year 2000 was 250 crore with cost index of materials being…

A: Solution: Given Data: P1=20 MWC2000=250 crCI2000=200CI2012=450P2=100 MWPSF=0.75

Q: Formulate or compose a problem solving (one or more problems) of Simple Rankine Cycle with its…

Q: A fan require at least 4.5 hp to deliver 18,000 CFM of air running at 320 rpm. For a service factor…

A: Horse power required, P= 4.5 hp Flow rate of air, Q= 18000 CFM Rotational speed, N= 320 rpm…

Q: 10°C. If the pressure ratio is 5 and the maximum temperature is 800°C, determine (a) the horsepower…

Q: What is the total work in Kjoules of a combined cyde power plant with a given plant efficiency of…

Q: Determine the minimum power required for a hoist crane that will lift a 20metric tons of load at the…

A: Given data: m = 20 metric ton = 20,000 kg V = 0.6 m/s Need to determine the minimum power required…

Q: 5.2.3 Steam at a pressure of 4MPA and a temperature of 350°C expands to 100kPa ina steam turbine.…

A: Solution: Properties at different state show in the T-s diagram above has to be calculated. At…

Q: An Ocean Thermal Energy Conversion (OTEC) power plant produces 25000 kW of ouput using warm surface…

A: Given:T1=29°C =302 KT2=12°C =285 KW=25000 KW

Q: An ideal gas Diesel engine, that has an inlet temperature and pressure of 19 °C and 102 kPa…

A: Given Data State 1:19°C,102 kPa Tmax=1285°C

Q: ncy and is equal to

A: given:efficiency η=87%

Q: 11.) A heat engine with &=0.450 operates between two heat reservoirs at 300K and 700K. During each…

A: Calculate the magnitude of Wk, QH, Qc for one cycle operation. Drawing energy flow diagram for one…

Q: A diesel engine in a power plant has an output of 2000 KW at 1000 rpm. It uses fuel oil having a…

A: Given data, g = 9.806 m/s2 Output power, P = 2000 kW RPM of the plant, N = 1000 rpm Heating value of…

Q: An air standard gas turbine engine operates on an overall pressure ratio of 4 and between the…

A: Answer: (a) The compressor work is 75.3884 Btu/lbm. (b) The turbine work is 148.7580 Btu/lbm. (c)…

Q: the rate at which heat is extracted from the refrigerated space.

A: Given; A refrigerator operates between =120 KPa and 800 KPa- in an ideal vapor compression cycle…

Q: power output is 2104.38kJ/kg

Q: A heat pump with the COP of 3.0 supplies heat at the rate of 240 kJ/min. Determine the electric…

A: 1) Given heat pump COP= 3 Heating effect (Q) = 240 kJ/min Concept: COP= Heating effect (Q) /Work…

Q: The rated boiler horsepower of a fire tube boiler is 500 Hp. What is the heating surface area of the…

Q: The following data pertains to a power plant of 120 MW capacity. Capital cost = Rs. 1500/kW.…

A: Given data The following data pertains to a power plant of 120 MW capacity. Capital cost = Rs.…

Q: 2. A 10 MW steam turbine generator power plant has a full- load steam rate of 12 kg/kw-hr. Assume…

Question

100%

Calculate the use factor in decimal form for at least two decimal point of a power plant if the capacity factor is 35% and it operates 8000 hrs during the year?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

A thermal power has a net power 10 MW. The backwork ratio of the plant is 0.005. Determine the compressor work.
Compute for the work net and the thermal efficiency of the cycle shown
13.46 is the answer for efficiency.
A mining pit about 5000ft below sea level was flooding as a result of heavy down pour. The situation is such that if quick and drastic measures are not taken severe damage could be cause to lives and properties. As the pit superintendent (mining engineer) a) What kind of pump is suitable for this kind of operation and why? In a power plant, the steam from the boiler reaches the turbines at a temperature of 700oC. The spent steam leaves the turbine at 100oC. b) Calculate the maximum efficiency of the turbine As the project consultant for Green court engineering consults, you have been contracted by Total power development authority to present a detailed proposal on an intended project to explore an additional generation units to increase capacity. (c) In your capacity as the project engineer, why is the project necessary?
Pls... Answer this problem? thank you! A small steam turbine power plant of 5000 kw capacity has a full load steam rate of 6 kg steam per kw-hr. No load steam consumption may be taken as 10% of full load steam consumption. Write the equations of WILLANS LINE of this turbine and at 60 % of rated load. Calculate the kg/hourly steam consumption of this unit.
A boiler plant raises 5.2 kg/s of steam at 1825 kN/m² pressure, using coal of calorific value 27.2 MJ/kg. If the boiler efficiency is 75%, how much coal is consumed per day? If the steam is used to generate electricity, what is the power generation in kilowatts assuming a 20% conversion efficiency of the turbines and generators?
Provide the given, manual step by step solution, and diagram of below problem. The heat added to a Carnot cycle is 1000 Btu/hr. The temperatureranges are at 80 Fahrenheit and 1400 degree Fahrenheit. Find the horsepower output of the cycle.
A prototype under experiment is being test to generate electricity via turbine generator assembly and using heat from solar panels. The system requires 61kWh of heat in the boiler in order to generate vapor for the turbine. The average solar radiation for the whole year is 6.5 kWh/ m2/day. How much collector surface area does it need if the solar panel has a 20% efficiency?
An electrical power plant has an overall efficiency of 15%. The plant is delivered 150MW of power to a city, and turbines use coal as fuel. The burning coal produces steam at 190 0C, which drives the turbines. The steam is then condensed at 25 0C by passing it through cooling coils in contact with river water.a) How many metric tons of coal does the plant consume each day?b) What is the total cost of the fuel per year if the delivered price 10 USD per metric ton?c) If the river water is delivered at 20 0C, at what minimum rate must it flow over the cooling coils in order to that its temperature not exceeds 25 0C? Heat of combustion of coal is 33 kJ/g
Provide a complete given and computation. Include all the decimals. Steam engine with incomplete expansion receives saturated steam at 1.04 Mpa, expands it to 0.105 Mpa where release occurs. Exhaust is to a condenser at 40C. The actual engine uses 6070 kg/h of steam; it has a brake engine efficiency of 60% and a mechanical efficiency of 85%. The electric generator which it drives has an efficiency of 92%. (a) For the ideal engine, find the thermal efficiency and the mep. For the actual engine, determine (b) the brake work in kW and the brake thermal efficiency, (c) the indicated work in kW, indicated thermal efficiency and indicated steam rate, (d) the combined thermal efficiency and the combined steam rate.
Assume a blower operating at 4000 rpm compressing air from 68oF and 14.7psia to 8.5psig, handling 16000cfm at the design point with an efficiency of 70%. It is desired to find the operating conditions (BHP, H and Q) at 3600 rpm.
A large tank filled with water and open to the atmosphere is used to extinguish a fire in an ethylene production plant. The water is removed from the tank through a pump and then distributed to the hoses. It is desirable to deliver 1890 L of water per minute at a pressure of 15 bar. If the pump has an efficiency of 70.0%, how much labor must be supplied to the pump to meet discharge specifications?