Calculate the x-, y-, and z-coordinates of the mass center of the bracket formed from the steel plate of uniform thickness. 135 mm 195 mm Answers: i 125 mm 210 mm 100 mm mm mm mm

Q: Two parallel shafts have an angular velocity ratio of 4 to 1 are connected by gears, the largest of…

A: Given:Velocity ratio, G=4:1Number of teeths on larger gear, ZA=40

Q: The members CJ and CF of the loaded truss cross but are not connected to members BI and DG. Compute…

A: GIVEN DATA- A PLANE TRUSS GIVEN WE HAVE TO FIND FORCES IN GIVEN MEMBER CONCEPT USED - METHOD OF…

Q: Determine the magnitude of the vertical force C, for the simply supported beam, where w = 11…

A:

Q: If the resultant force of the forces system shown in Fig . ( 1 ) is to be ( 700 N ) directed along…

A:

Q: The distance y = 2.8 m. Find the upward velocity of A if the downward velocity of B is 3.8 m/s.…

A:

Q: (a) the net work of the cycle, in kJ. (b) the percent thermal efficiency. (c) the mean effective…

A:

Q: A fireworks show is choreographed to have two shells cross paths at a height of 176 feet and explode…

A:

Q: A machine with a mass of 30 kg is operating at a frequency of 60 rad/s. What equivalent stiffness of…

A: Given data, Mass = 30 kg , frequency = 60 rad/s we will use natural frequency formula to calculate…

Q: Determine the height h above the base of the centroid of the cross-sectional area of the beam.…

A:

Q: Find the mass of air in a closed cylinder. The pressure and temperature of a air is 14.7 psi, and…

A: given data: pressure of air P =14.7psi =1atm = 101.325kpa temperature of air T= 70F…

Q: Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable…

A: Given data: ◆ The tension in the rope ABC = 74 lb ◆ The angle made by cable ABC with horizontal =…

Q: A 14.5 degrees full-depth involute gear has an outside diameter of 5-1/3 in. and diametral pitch of…

A:

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A: Series Combination:- Series combination of bars is a type of series where axial deflection is…

Q: A square bottomed tank measures 25*25*160 and is positioned with the bottom of the tank above sea…

A: Given  Data Dimension of the tank =25×25×160cm volume percentage of water in the tank=90% Volume…

Q: Determine the force in member EF of the loaded symmetrical truss. Assume no horizontal reactions at…

A:

Q: The lining of box - type fumace is made up of a refractory 1 plate as shown in the figure. Steady…

A:

Q: The horizontal force P = 85 N is applied to the upper block with the system initially stationary.…

A: F.B.D. of the given system:

Q: Determine the coordinates of the mass center of the body which is constructed of three pieces of…

A: Given question: Determine the coordinates of the mass center of the body which is constructed of…

Q: Train A is traveling at a constant speed VA = 35 mi/hr while car B travels in a straight line along…

A: VA = speed of the train = 35 mi/hr = 35×52803600 ft/s = 51.333 ft/s VB = speed of the car VC/A =…

Q: 5 ☆ ☺ T Ô (a) Forces of magnitude F, 2F, 3F, 4F, 2F, 6F, F. and 2F act along the sides AB, BC, CD.…

A: We will answer the first question since the exact one was not specified. Please submit a new…

Q: The truss is composed of equilateral triangles of side a = 2.4 m. The load is L = 370 N. Determine…

A: Given data: Side length of triangle (a) = 2.4 m Magnitude of the load (L) = 370 N Concept: At…

Q: A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is…

A:

Q: Determine the percent reduction n in the polar moment of inertia of the square plate due to the…

A: Given data: ◆ Assume a = 2.0 × R ◆ The side of the square = 2a ◆ The radius of the circle = R…

Q: Determine the centroidal y-coordinate (in mm, round-off to 2 decimal places) of the volume shown. 5…

A: Given problem is

Q: Rod CD rotates with an angular velocity of @CD= 3.23 rad/s as shown. Determine the angular velocity…

A: Given Data  distance of CD=1m Distance of CB=1.5m distance of AB=1m Angular velocity along…

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 45 45 x = y Answers: y = 175…

A:

Q: A force of 100N makes an angle Ɵ with the x-axis and has a y-component of 30N. Determine both the…

A:

Q: 5.) Air is kept at a pressure of 135 MPa absolute and a temperature of 15 C in a 7000 ml container.…

A:

Q: 1- The bearings at A and B exert only y and z components of force on the shaft. If Sy 150 MPa for…

A: Given: The yield strength of material, SY = 150 MPa The shaft diameter, d = 40 mm

Q: Calculate the x-, y-, and z-coordinates of the mass center of the bracket formed from the steel…

A:

Q: A 1959 lb car starts from rest at point 1 and moves without friction down the track shown. Determine…

A:

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A:

Q: s forged in an open die. The workpiece is 60 m rging is 15 mm. The coefficient of friction at ation…

A:

Q: w many revolutions per minute is a spur gear turning, if it has 30 teeth, a circular pitch of…

A: Given:Number of teeth, Z=30Circular pitch, Pc=0.785 inPitch line velocity, v=15 ft/s

Q: The composite shaft consists of two steel pipes that are connected at flange B and securely attached…

A:

Q: Shown in the Figure is the complete pump performance chart for a 3x4-10 centrifugal pump at 1750…

A: Given question: Shown in the Figure is the complete pump performance chart for a  3×4-10 centrifugal…

Q: Consider a combined gas-steam power plant that has a net power output of 270 MW. The pressure ratio…

A: During Consideration of a gas-steam power plant, it is working on the principle of the gas-steam…

Q: The two blocks shown are originally at rest. Neglecting the masses of determine the tension in the…

A:

Q: he figure shown below is a series pipeline system used to draw a fluid from a lower source open tank…

A: Given       Volume flow rate: Q=0.015 m3/s                     Length: Ld=100 m Elevation…

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A: Given problem is

Q: For the simply supported beam subjected to the loading shown, derive equations for the shear force…

A:

Q: In the figure, aluminum [E = 75 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a…

A:

Q: A simple torsion-bar spring is shown. The shear stress in the steel [G-11,500 ksi] shaft is not to…

A: Given:Maximum shear stress in the steel, τmax=8600 psimodulus of rigidity of steel, G=11500…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A: Given: Let's determine the force in member BE and CE.

Q: 2.) The specific weight of a certain gas was 3.53 dyne/cm^3 at pressure gage 1.4 MPa and gas…

A: Given: specific weight = 3.53 dyne/cm3  Pgage = 1.4 MPa R = 746.36 J/kgK   Useful conversion…

Q: Q3: Find the required moment to hold the curved gate (radius 1.5 m,

A:

Q: If block A is intended to move vertically at a constant rate of 2.36m/s, determine the rate (m/s) at…

A:

Q: If a force of P=25N is applied to the handle of the mechanism, determine the  force the screw exerts…

A:

Q: For the simply supported beam subjected to the loads shown. Let a=3.00 m, b=4.00 m, PB = 30kN, and…

A: Given data: ◆ The values of point loads applied on the beam: PB = 30 kN , Pc = 65 kN ◆ The length of…

Q: The 200 x 200 x 1.250-mm oak (E-12 GPa) block (2) shown is reinforced by bolting two 5x200x1.250mm…

A: