Calculate the yardage required to construct a full-size bed 54”w * 75"l. Calculate the yardage required to construct two pillow shams for a standard pillow 26”w * 20l”.
Q: Q-2: A simply supported beam is 25 x 50 cm deep and has 2-20 mm Fe 415 grade steel bars going into…
A:
Q: A retaining wall of height 10 m retains dry sand. In initial state, the soil is loose and has a void…
A: Height of retaining wall H=10 m, Initial state, stress parameters- Unit weight-γ1=18 kN/m2,Void…
Q: A trapezoidal channel has a bottom width of 6 m and a side slope of 1:1. The depth of flow is 2 m at…
A: Depth of flow y=2 m, Discharge Q=24 m3/s, Side slope = 1 : 1, Width B=6 m, It is needed to find…
Q: Hi there, the answer you provided is wrong. why is that?
A: Frame height = 39 ft Story height = 13 ft Tributary depth = 20 ft Windward pressures at each…
Q: Water flow passes under the sluice gate. Suppose that y₁ = 6 m and y2 = 1.9 m. (Figure 1) Figure Y₁…
A:
Q: Q- Using Unit Load Method, find the load (W) kN/m, to make the horizontal deflection at point (C)…
A:
Q: FOR A RECTANGULAR BEAM (400mm x 700mm), calculate the following: (a) Maximum flexural stress of the…
A: A beam is given we need to find out flexural stress
Q: Find the moment of inertia about the strong axis in in^4 of the I-section shown in the figure below.…
A: Determine the moment of inertia about the strong axis.
Q: The structure below is supported by a pins at A and B. Determine the pin reactions at A, B, and C.…
A: Reactions at A,B and C
Q: CHAPTER 7 WASTE HANDLING AND SEPARATION, STORAGE AND PROCESSING AT THE SOURCE Q4 Estimate the energy…
A: The solid waste is important in evaluating the needs of equipment's, system and the management…
Q: If the void ratio and discharge velocity for soil is 0.5 and 6 x10-7 m/s respectively, what is the…
A: A soil sample- Void ratio e=0.5,Velocity v=6×10-7 m/s, To find- The value of the seepage velocity…
Q: Determine the degree of indeterminacy for each of the following structures:
A:
Q: a square footing with a size of 10 ft by 10 ft is located 8ft below the ground surface. the subsoil…
A:
Q: what is the advantages of SAP and stadd in steel design
A: SAP and STAAD are both software tools which are commonly used in structural engineering for both…
Q: = Oil (kinematic viscosity, Voil = 1.0 × 105 m²/s) flows through a pipe of 0.5 m diameter with a…
A: Viscosity of oil Voil=1×10-5 m2/s Diameter of pipe Doil=0.5 m For water- vw=0.89×10-6 m2/s Diameter…
Q: n e 7-15. Determine the internal normal force, shear force, and moment at point C. 6 kN/m - 3 m C…
A:
Q: Determine the reactions in the beam shown using the Maxwell-Mohr method. 75 kN - m Ac 1 6 m- 120 kN…
A: Point load (P) = 120 kn Moment (M) = 75 kn-m Length (L) = 12 m Side (a) = 6 m
Q: 4. The beam shown in figure below (W 410 x 46.1) has continuous lateral support of both flanges. The…
A: Given Data: Section: W 410 x 46.1 fc = 35 MPa A36 steel: fy= 250 mm fu = 450 MPa
Q: A W14 x 30 structural A992 steel column shown in (Figure 1 ) is pin connected at is ends and has a…
A:
Q: Wide flange shapes, (W-shapes), are considered economical members because: O the majority of the…
A: A wide flange shape, also known as W-shape, is a structural steel member which is commonly used in…
Q: According to the Working at Height Regulations, state: a) the minimum height at which precautions…
A: Working at heights means that the labor is working at a certain height above ground level and if…
Q: The flow ratio of a Francis turbine, if it is working under a head of 62 m and velocity at inlet 7…
A: Working head (H) = 62 m Velocity at inlet (V) = 7 m/s g = 10 m/s2 Determine the flow ratio of a…
Q: Q8/ Given a velocity field V = (4 + xy + 2t)i +6x³j+(3x²+2) k. Find the acceleration of a fluid…
A:
Q: Determine the horizontal displacement of joint C. A L B The length, L, of trusses AC, BC is 1,500…
A:
Q: A flexible pavement is constructed with 225 mm (8.86 inches) wearing surface of hot-mix asphalt with…
A: Wearing surface of hot mix asphalt with high rut resistance - 225 mm (8.86 inch)Recycled mixture…
Q: a) Calculate an expression in terms of Young's Modulus, E, and Second Moment of Area, I, for the…
A:
Q: Consider the rod shown in (Figure 1). Suppose that h = 170 mm. r = 290 mm.
A:
Q: A steel bar of 40 mm x 40 mm square cross-section is subjected to an axial compressive load of 200…
A: Dimensions=40 mm×40 mm,Load P=200 kN,Length of the bar L=2 m,E=200 GPa, Deformation of the bar?
Q: Design three solids handling unit processes: (a) an anaerobic digester to treat a plant's primary…
A: a) To calculate the mass of sludge wasted that each digester will have to stabilize, we need to…
Q: Determine the magnitude of the hydrostatic force acting on gate AB, which has a width of
A: The hydrostatic law states that the pressure acting on point inside the fluid increases with…
Q: Use only Direct Integration Method 2. AF K M 2 B kN/m 60 mm * MM त्र d 3 EI= 5x10² KN m² Sc 0₂= 1)
A:
Q: Q.10 For an I-beam, shape factor is 1.12. The factor of safety in bending is 1.5. If the allowable…
A: An I-beam, Shape factor SF=1.12 FOS=1.5 Increase in allowable stress=20% To Find- The value of the…
Q: 4. Ball A rotates without friction on the end of a 30cm rod. Cart B rolls freely in the horizontal…
A:
Q: A stream function is given by y = 3x² - y³. What is the magnitude of velocity components at the…
A: Stream function- ψ=3x2-y3 To Find- The magnitude of velocity components at point (2, 1).
Q: An unsymmetrical parabolic curve has a forward tangent of -8% and a back tangent of +5%. The length…
A:
Q: c. Calculate the sludge volume (ft³/day) that the digesters must stabilize each day. d. If the h:D =…
A: c) The sludge volume (ft³/day) that the digesters must stabilize each day is given by: Sludge volume…
Q: E. Combined Flexure and Axial Example E.3: Second Order Bending and Axial Given: Braced column with…
A:
Q: 3-) Water flowing through a cast iron horizontal pipe with a roughness of 0.122 cm and a length of…
A: A cast iron horizontal pipe is given, Roughness of 0.122 cm Length = 60.69m Flow rate = 0.0334 m3/s…
Q: Q- In a 1:36 scale model test of a spillway, discharge of flow over the model is 6 m³/s. If the…
A: →p= prototype , m= model→Qm=discharge of flow =6m3sec→Vm=5 knotmsecTo determine :velocity of flowVp
Q: 3) Determine the annual soil loss from an urban area that is under development and has the following…
A: The average annual rainfall erosivity, R = 150 The slope length, L = 500ft The steepness, S = 1%…
Q: 45. A 7x3/4 in. A36 plate is shown in Figure P4.45, where the holes are for 3/4 in. bolts. Determine…
A: Grade of Steel = A36 Gross area(Ag) = 5.25 in2 Thickness (t) = 0.75 Diameter of the bolt (db)=34 in…
Q: 10n B 6 klf -30 ft Problem 6.23 draw the shearing force and bending moment diagrams for the…
A:
Q: How do you convert gpm to ft?
A: A cross-sectional area's flow of fluid is measured in gallons per minute. In simple terms, it…
Q: roblem 2: A steel pressure tank has an inner diameter of 1.5 m and a wall thickness of 28 mm the…
A: Diameter of tank=1.5m Thickness of tank=28mm Internal pressure=5MPa
Q: For the state of stress (MPa) shown in the figure below. The ratio of Major principal stress to…
A:
Q: GIVE THE FIVE ELEMENTS OF GREEN BUILDING
A: Green building is a design strategy that tries to reduce a building's environmental effect while…
Q: 5. Design a bearing plate to distribute the reaction of the W 410 x 46.1 in problem (4). The beam is…
A: Given: Section: W 410 x 46.1 fc = 35 MPa A36 steel: fy = 250 mm fu = 450 MPa
Q: Q- In a 1:36 scale model test of a spillway, discharge of flow over the model is 6 m³/s. If the…
A: →p= prototype , m= model→Qm=discharge of flow =6m3sec→Vm=5 knotmsecTo determine :velocity of flowVp
Q: The average wastewater characteristics produced by a food processing plant are shown in Table A.2.…
A: Anaerobic treatment is a viable option for treating wastewater generated by food processing plants.…
Q: 1. A gravel bed river with large boulders carries a flood discharge of 190,000 cfs during a 100-…
A: According to Bartleby Guidelines only 1st question will be answered. Please post the second question…
Calculate the yardage required to construct a full-size bed 54”w * 75"l.
Calculate the yardage required to construct two pillow shams for a standard pillow 26”w * 20l”.
Step by step
Solved in 4 steps
- Calculate the yardage required to construct two pillow shams for a standard pillow 26”w * 20l”.If you have a room that is 13’ 7” x 18’ 5”, how many Square Yards (SY) of carpet do you need for the room.While repairing a baseboard hot water heating system, a technician drops alighted blowtorch, badly damaging the rug. How many square yards ofcarpeting will be needed to replace the damaged rug? Round to the nexthigher full square yard.
- Complete the table asapYou are to construct a Bodega with a rectangular floor plan using CHB (Concrete Hollow Blocks) as a material for walls. The floor area is 18 sq.m. The floor to ceiling height is 3.00m. The length of the North and South side are the same. The lengths of the North/South are twice the same as the East/West side. In the North wall, you have a standard door with dimensions of 0.90mx2.10m. In the South Wall, You have two windows; each has an area of 1sq.m each. How many pieces of CBH do you need in order to construct 4 walls of the bodega if a CBH has a dimension of Length – 40cm, Height – 20cm, Depth 10cm and 15 cm.? If 1 pc, CBH is Php. 15.00 How much do you need to spend to construct 4 walls of the bodega with a 10% contingency fee?A gallon of water weighs 8.34 pounds. The Stean family has a round, 12-foot diameter, above -ground pool. How muc is added to the pool when it is filled with 3,195 gallons of water? Please answer it only correct with full explanation.
- Q: (i) How to orient a hospital building so that it can get maximum natural light and ventilation. Please describe the reason why you are selecting the particular type of orientation. (ii) And which type of material should be used for constructing doors,windows and ventilators.Also give the reason behind your decision.I need help with part B, thank you. Kitchen Master Bedroom 25.2 18.0 17.4 22.9 22.8 26.4 21.9 24.8 19.7 26.9 23.0 17.8 19.7 24.6 16.9 21.0 21.8 23.6DRAW ON PAPER a bubble diagram of a 3,500-square-foot 3-level home. The lower level of the house should have storage for bikes, kayaks, and gardening tools. A 2-car garage with storage. The main level living will have a front porch and a deck and should be designed as an open floor plan with few room separations for bathrooms and bedrooms. The upper floor will have a guest bedroom/ bonus room with a bathroom, an office on the main level, and a large day-lit kitchen.
- SHOW COMPLETE SOLUTIONS AND DRAWINGS: You are to construct a Bodega with a rectangular floor plan using CHB (Concrete Hollow Blocks) as a material for walls. The floor area is 18 sq.m. The floor to ceiling height is 3.00m. The length of the North and South side are the same. The lengths of the North/South are twice the same as the East/West side. In the North wall, you have a standard door with dimensions of 0.90mx2.10m. In the South Wall, You have two windows; each has an area of 1sq.m each. How many pieces of CBH do you need in order to construct 4 walls of the bodega if a CBH has a dimension of Length – 40cm, Height – 20cm, Depth 10cm and 15 cm.? If 1 pc, CBH is Php. 15.00 How much do you need to spend to construct 4 walls of the bodega with a 10% contingency fee?Isobel and Neliwe’s garage floor is 5400 mm long and 3000 mm wide. 1.1Convert the dimensions of Isobel and Neliwe’s garage into meters. 1.2They went to the TCN warehouse and found that the length of one tile is 350mm. How many tiles are needed to tile one row along the length of the garage? 1.3One tile is sold at R5.17, how much will it cost to tile only one row along the length of the garage.ASAP please help me with this.