Calculation: Compressive Strength (CS) = P/A Where: CS = compressive strength of the specimen, psi (KN/m²) P = maximum load, Ib (KN) A = cross-sectional area of the specimen, inches (m²) Gross Area: Tabulated Data and Result Trial No. b (m) w (m) A (m²) P (kN) CS (kN/m²) 1 0.4 0.15 0.06 150 2 0.4 0.15 0.06 180 0.4 0.15 0.06 140 Net Area: Tabulated Data and Result Trial No. A (m²) P (kN) CS (kN/m²) 1 0.0296 150 0.0296 180 3 0.0296 140

Calculation: Compressive Strength (CS) = P/A Where: CS = compressive strength of the specimen, psi (KN/m²) P = maximum load, Ib (KN) A = cross-sectional area of the specimen, inches (m²) Gross Area: Tabulated Data and Result Trial No. b (m) w (m) A (m²) P (kN) CS (kN/m²) 1 0.4 0.15 0.06 150 2 0.4 0.15 0.06 180 0.4 0.15 0.06 140 Net Area: Tabulated Data and Result Trial No. A (m²) P (kN) CS (kN/m²) 1 0.0296 150 0.0296 180 3 0.0296 140

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider a standard flexural strength specimen of length L, width a, and depth a. Assume third point loading where the load at failure from the test machine is P, which is distributed evenly (½ to each) over the two loading points. Derive the equation for calculating the modulus of rupture of the beam in terms of P, L, and a.
Consider a standard flexural strength specimen of length L, width a, and depth a. Assume third point loading where the load at failure from the test machine is P, which is distributed evenly (½ to each) over the two loading points. Derive the equation for calculating the modulus of rupture of the beam in terms of P, L, and a. Show complete solution
A sample of sand is sheared in the following manner. First an all around normal stresso 350 kPa is applied to the sample. Next a shear stress is applied to the horizontal pia while the normal stress remains constant. The shear stresses at failure are + 186 kPa. Ihe initial stress and stress condition at failure are shown below 350 kPa 350 kPa 186 kPa 350 kPa 350 kPa ー550 kPa 550 kPa 186 kPa 350 kPa 350 kPa Initial Conditions At Failure Determine the Following: fo A) Assuming c, = 0, draw a failure envelope for the soil. Define the friction angle ( the soil. B) Draw the Mohr's Circle at failure for the test. C) Show the location of the pole. D) Define the maximum and minimum principal stresses at failure. E) Define the normal stress corresponding to the maximum shear stress
For a Brinell Hardness Test, find the BHN if the force applied is 100kgf with indenter diameter of 10mm and indentation diameter of 8.4mm For a Vicker's Test, find HV in MPa if applied force is 100kgf with impression diagonals are 10mm and 8.4mm, respectively
help asap huhu A cylindrical specimen of a saturated soil fails under a stress of 150 kPa in an unconfined compression test . The failure plane makes an angle of 52° with horizontal a.) Compute the angle of internal friction of soil b.) Compute the cohesion of the soil c.) compute the shearing stress at failure Plane.
Describe suction in stress path analysis.
a. Assuming the computer and the printer are turned on, what will be the next step to do when trying to perform a test?b. What part of the UTM will you use to remove the tensile test specimen from the grips?c. In what direction does the lower crosshead move during a tensile test?d. In what direction does the lower crosshead move during a compression test?e. In what direction does the lower crosshead move during a bending test?
Define the term effective stress.
Consider a bar with a rectangular cross-section area with a thickness of t = 0.5 in. and height of h = 3.5 in. When force P = 19 kips is applied to the bar, the strain gages attached to the surface of the bar reads εx = 740 µε along the direction of the force and εy = -170 µε in the perpendicular direction. Determine Poisson's ratio for this specimen? Determine the modulus of elasticity for this specimen?in Ksi
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion? Given data: -The yield strength of the pressure vessel is σy = 250 MPa.The inner diameter of the vessel is d = 2 m.The pressure acting in the vessel is P = 10 Atm.The longitudinal Stress is σL = 200 MPa.Hoop Stress σθ = 150 MPaThe Radial Stress is σR = -50 MPa.
A tension test is being conducted on a steel-rod specimen with a gauge length of L0=50mm and initial diameter of d0=13mm. Data were collected to form the conventional stress-strain diagram as shown. From the diagram, f = 510 MPa , e = 693 MPa , g = 565 MPa , and ℎ = 0.15 mm/mm Assuming that the strain remains constant throughout the region between the gauge points, determine the nominal strain ε experienced by the rod if it is elongated to L = 65.0 mm.
Tension specimens (diameter d0 0.500 in., gage length L0 2.00 in.) made of structural materials A and B are tested to failure in tension. (a) At failure the distances between the gage marks are LAf 2.90 in. and LBf 2.22 in.; the corresponding diameters at the failure cross sections are dAf 0.263 in. and dBf 0.471 in., respectively. Determine the percent elongation in 2 in. and the percent reduction in area for these two materials, and classify each material as either brittle or ductile. (b) From these tensile tests the following data are also obtained: EA 10.0 103 ksi, (Y)A 5 ksi, (U)A 13 ksi; EB 10.4 103 ksi, (Y)B 73 ksi, (U)B 83 ksi. From the data given here, make rough sketches (to scale) of the stress-strain diagrams of materials A and B.