CAN SOMEONE PLEASE HELP ME WITH MY STRUCTURAL THEORY PROBLEM Please write legibly with complete solution. FOLLOW THE INSTRUCTIONS STRICTLY THE INFLUENCE LINES OF BEAMS Draw the influence lines for the vertical reaction at A and B of the given beam. The modulus of elasticity is constant. 21 I 20ft 10ft 20ft A B

CAN SOMEONE PLEASE HELP ME WITH MY STRUCTURAL THEORY PROBLEM Please write legibly with complete solution. FOLLOW THE INSTRUCTIONS STRICTLY THE INFLUENCE LINES OF BEAMS Draw the influence lines for the vertical reaction at A and B of the given beam. The modulus of elasticity is constant. 21 I 20ft 10ft 20ft A B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Note that: a = 3.7 m b = 31.0 kN/m c = 35 kN Find the ff. A. Vertical reaction at B in kN. B. Moment reaction at A in kN-m. C. Deflection at point C in mm. D. Deflection at midspan of AB in mm.
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x150 mm section and E = 80 GPa. Show complete and organized solution. a. Vertical Reaction at B in kN. b.Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. Given: a- 7m b- 24kN/m C- 30kN
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solutions. a. Vertical Reaction at B in kN.b. Moment Reaction at A in kN-m.c. Deflection at point C in mm.d. Deflection at midspan of AB in mm. Valuea = 3.7b = 26c = 29 Thank you very much!
Design a most economical spiral-column cross-section to support factored forces and end moments of Pu = 1,600 kips and Mu = 150 kip-ft. Assume that the centroid of the longitudinal bars from the edge of the column is 2.5 inch. Using the interaction diagram, how many #9 rebars will be used? Express your answer in whole number.
Determine the reactions in pounds the hinge and the rocker exert on the beam supporting the distributed load. (Assume that the +x-axis is to the right and the +y-axis is up along the page. Due to the nature of this problem, do not use rounded intermediate values in your calculations or answers) Magnitude and direction Magnitude in lbs. Ax- Magnitude is 0 Ay- By-
18. The beam which is supported by hinge and roller at its ends, is called as a. simple supported beam b. continuous beam c. propped beam d. cantilever beam 19. Which of the following is statically determinate beam? a. simply supported beam b. cantilever beam c. overhanging beam d. all of these 20. Which quantity does not affect Shear Force Diagram? a. Point load b. Uniformly distributed load c. Uniformly varying load d. Couple
Determine the bending moment 2.16 m to the right of point A for the beam shown belowif P = 1990 N, T = 4712 Nm, a = 0.99 m, b = 0.7 m, and c = 1.29 m. Round of the final answer (in N m) to four decimal places.
A cantilever beam is 4m long with a EI = 20MNm^2. It has a point load of P=1kN at the free end and a u.d.l of q = 300N/m along its entire length. what is the reaction at A? what is the moment at A? Calculate the following at the free end slope and deflection
(i) A tie bar is 2.5 m long, has a circular cross section of 50 mm in diameter and is subjected to a force of 250 kN. Given that Young’s Modulus E = 209 kN/mm2 and Poisson’s Ratio ν = 0.3 calculate the change in volume of the bar when loaded. (ii) Draw the shear force and bending moment diagrams for the cantilever beam shown in the image attahced clearly indicating all significant points.
Determine the following unknowns on the beam shown below using Conjugated-Beam Method. Consider 250 mm x 250 mm and E = 200 GPa. Note: a = 4.5 m b = 33.0 kN/m c = 13 kN Find the ff. A. Vertical reaction at C in kN. B. Moment reaction at C in kN. C. Deflection at point B in mm. D. Maximum deflection on the beam in mm.
The 426-kg uniform beam is subjected to the three external loads shown. Compute the vertical reaction (N) at the support point O if P = 4189 N, Q = 3243 N, T = 40187 Nm, x = 1.02 m, y = 1.43 m, and z = 1.56 m and the system is in equilibrium.Positive values are to the right, up, and counterclockwise. Round off only on the final answer expressed in 3 decimal places.
Must include explanation , Don't Just copy ,I will rate accordingly. Q: A square ABCD has sides equal of 200 mm (Figure Q2 (a)). Forces of 150 N each act along AB and CD and 250 N acting along CB and AD. Evaluate the moment of the couple, which will keep the system in equilibrium.