Capacitors – if V1(t) is at the vdd potential (large and positive) at t = 0, derive an equation for V1 as a function of time. Provide a LARGE hand-drawn sketch of V1(t) for t>0. Label all relevant points in the graph. Be especially clear about any curvatures and the value of the boundary conditions. vdd vdd R1 C1 V1 R2

Capacitors – if V1(t) is at the vdd potential (large and positive) at t = 0, derive an equation for V1 as a function of time. Provide a LARGE hand-drawn sketch of V1(t) for t>0. Label all relevant points in the graph. Be especially clear about any curvatures and the value of the boundary conditions. vdd vdd R1 C1 V1 R2

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.18P

See similar textbooks

Similar questions

Let be the first-order electric circuit shown in the figure below. It is known that the switch T changes state, from open to closed, at instant t=0 and that, once said switch is activated, the network reaches the stable state after 500 ms a) Find the expression for the voltage v(t), for all t>0b) Find the value of the capacitance Cc) Represent graphically, and approximately, the behavior as a function of time of the voltage found in part a)
Given the circuit below with the switch closed for a long time, then opening at t=0, and with the values R1=129KΩ, R2=128KΩ, R3=103KΩ, calculate the time constant, τ, for the capacitor voltage solution for at t >0.
Consider the circuit shown in the figure, with ε=36.0V,R0=50.0Ω,R=150Ω andL=4.00H. (a) Switch S1 is closed. Just after S1 is closed, what are the current i0 through R0 andthe potential differences VAC and VCB? (b) After S1 has been closed a long time so that the current has reached its final, steadyvalue, what are i0 , VAC and VCB? (c) Find the expressions for i0 , VAC and VCB as functions of time since S1 was closed.Do your results agree with what you get in (a) and (b) ? Graph i0 , VAC and VCB as afunction of time.
RL Force Response 1. What is the value of io before and after the switch changes position? 2. What is the value of vo before and after the switch changes position? 3. What is the value of io and vo at t = inf? 4. What is the value of Rth (Thevanin Resistance) by the inductor for t > 0? 5. Determine the circuit's time constant ? for t > 0 in ms. 6. Derive expression for iL(t) for t > 0 and for its value at t = 1.5 ms using complete response formula.
In the circuit shown below, the switch has been open a long time and the circuit is initially in steady-state. At t=0, the switch is closed. R1=0.2Ω, and R2=0.4Ω. The batteries have EMFs E1=1V and E2=3V. The capacitor has capacitance 10 μF. Hint: What is the voltage on the capacitor just before the switch is closed? Note that there is a voltage drop over the open switch. a) What is the voltage over the capacitor before the switch is closed? b) Draw the Thevenin equivalent circuit as seen by the capacitor. c) What is the time constant for charging the capacitor? d) What is the voltage on the capacitor as a function of time?
Application of Differential Equation A circuit has in series of electromotive force given by E(t) = 100 sin 60t V, a resistor of 2 Ω, an inductor of 0.1 H, and a capacitor of 1/260 farads. If the initial current and the initial charge on the capacitor are both zero coulombs, find the charge on the capacitor at any time t > 0.
My teacher said that the equation v(t) for Vcap (in image) will be V = -1/C integral of i(t) + v(initial). My question is, my teacher has said that the '-' infront of the 1/C is because the current flows into the negative terminal of the capacitor. But in the answer my teacher has put v(initial) as +20 and not -20, even though the 20V across the capacitor is also negative to positive as shown in the image. So why is the v(initial) put as +20 and not -20? Thank you.
How can an underdamped second-order system be identified? What form does its complementary solution take? Repeat for a critically damped system and for an overdamped system.
Let the voltage applied at the input v1 be R1=R2=C1=C2. Find the differential equation provided by the current i2. a) If v1=5, find the permanent and temporary answer of i2. Initially, assume that there is no charge on the capacitor. b) Find the permanent answer of i2 in case of v1=10sin7t. How do you find the temporary answer?
From the given circuit. Switch S1 is in position A switch S2 is open. Both switches are in these states for a very long time. At t=0, switch S1 moves from position A to B while switch S2 remains open. 10ms after switch S1 moves to position B, switch S2 is closed and remains closed for 20ms only. ANSWER THE FOLLOWING: a.) Expression for the inductor current for 0 ≤ ? < 10??b.) Expression for the inductor current for 10?? ≤ ? < 30?? and 30?? ≤ ? < ∞c.) What is the time (in ms) after switch S1 moves to position B is the current in the inductor equivalent to 30% of the initial value (at ?=0).
Assume at t=0, a switch in an RC circuit in which the resistor and capacitor are in parallel is closed. how would this affect voltage, charge, and current at t=0 and after a very long time? what if this scenario was the opposite, in which the switch was opened rather than closed? what effect would this have?
A)Just after the switch is closed, what is the magnitude of the potential difference Vab across the resistor R1? B)Magnitude of the potential difference Vcd across the inductor L? C)The switch is left closed a long time then opened. Just after the switch is opened, what is the magnitude of the potential difference Vab across the resistor R1? D)What is the magnitude of the potential difference Vcd across the inductor L?