Centroid From fig above find area 1 a. 1397 b. 1434 c. 1534 find area 2 a. 1843 b. 1924 c. 2042 find area total a. 3576 b. 3277 c. 3321 find y bar a. 74 b. 84 c. 94 find x bar a. 33 b. 43 c. 54

Q: The principal stresses at a pc perpendicular planes are 76 and 34MN/m² (tensile). Find t tangential…

A:

Q: Design the pin ended steel column in S275 steel to withstand an axial compressive load of 2500 KN…

A: To find:Whether the given section is adequate to carry the given load.Given:356 x 368 x 129…

Q: Required information A square yellow-brass bar must not stretch more than 105 GPa and that the…

A:

Q: The cross-sectional area of each member of the truss shown in the figure is A = 400 mm² and E = 200…

A: Area of members, Modulus of elasticity, To find:(a) The vertical displacement at joint C under…

Q: At room temperature (24°C) a 0.5 mm gap exists between the ends of the rods shown in the figure. At…

A:

Q: In a Marshall sample, the bulk specific gravity of mix and aggregates are 2.424 and 2.644…

A: Bulk specific gravity of mix Gm=2.424Bulk specific gravity of aggregate =2.6447% of…

Q: If an analysis is made of the hydraulic conductivity of a site using permeameter tests of core…

A: Slug method K is as low as 1.0 x 10-5 m/yrConstant-head conductivity test K> 1.0 × 102…

Q: A mild steel bar, 1.5 m long, has a square section 40 mm x 40 mm. The bar is subjected to a two-…

A:

Q: A square high-density polyethylene [a = 158 x 10-6/°C] plate has a width of 295 mm. A 177 mm…

A: Given data in question Width 295 mmDiameter 177 mmCoefficient of thermal expansion 158×10-6…

Q: Calculate Superelevation for a horizontal cure with redius 300mand wides 8m. the design speed 50…

A:

Q: The rise and tread of staircase are 150 mm and 250 mm and weight of slab on slope is 5 kN/m2. The…

A: Rise of the staircase R=150 mmTread of the staircase T=250 mmWeight of slab on slope w=5 kN/m2To…

Q: C a N₁ W b Су Cx

A:

Q: Param. Moment 1 [M₁] * Moment 2 [M₂] * Moment 3 [M3] * Moment 4 [M4] * CONCENTRATED MOMENTS Ya.…

A: Given data in question Concentrated moments M1 and M5Span of beamTo find out What needs to be…

Q: Assume that you are going to make a three cubic yard (3yd³) of concrete. Create your own mix design…

A: The design strength = 3.8 ksiThe slump should = 3 to 4 in.The maximum size of aggregate = 2 inUnit…

Q: All problem solutions must include FBDs. 7-1. Determine the shear force and moment at points C and…

A: "Note" :- As per our policy we can solve only first question . Post another question separately.…

Q: A simply supported prestressed concrete beam is of 25m span. The initial stress is 1000 MPA. The…

A:

Q: A chain, working a crane, has sectional area of 625 mm² and transmits a load of 10 kN. When the load…

A: Given data-To Find-Stress-induced in the chain.

Q: The crank OA is shown. If OA = 68 mm, 0 = 20°, and 3 = 20°, determine the moment of the force F of…

A: Given - OA =68 mm Angle theta = 20° Angle Beta = 20° F = 22 N Find out - Moment of the force F about…

Q: What is the stress at the section x - x. for the bar ABCD with uniform cross-section 1000 mm²? с A…

A:

Q: 1. Classify the soil using USDA triangular texture classification with the following data: Sand-…

A:

Q: Question 1 If the coefficient of active earth pressure is 1/3, then what is the value of the…

A: Coefficient of active earth pressure = 1/3

Q: The comply with architectural requirements, a column in a non-sway frame is of T-section as shown.…

A: IntroductionThe centroid of a geometric shape, commonly referred to as the center of mass or…

Q: What are the societal advantages of architecture? Examine the distinctions between a project…

A: Societal advantages of architecture. The distinctions between a project incorporating architectural…

Q: (a) The tapered shaft is confined by the fixed supports at A and B. If a torque T is applied at its…

A:

Q: Water flows in a trapezoidal channel with side slope 1V:3H, bottom width of 16ft and water depth of…

A:

Q: The driver of a vehicle approaching a signalised intersection at a speed of 40 kmph applied brakes…

A: Speed u=40 kmphAmber time=4 sReaction time=1 sTo Find-The average friction coefficient developed.

Q: A sewage sludge has a water content of 99%. The concentration of suspended solids in the sludge will…

A: Water content=99%Density of wet sludge = 1000 kg/m3To Find-The concentration of suspended solids in…

Q: Q3) Determine the force in each member of the truss. State if the members are in tension or…

A: A truss is pinned at A and a roller supported at D, to this truss, a 10kN vertical load, and 6kN…

Q: A 36-m² filter with the characteristics shown below operates 47.5 hours between backwashes and the…

A: Area of the filter A=36 m2To Find-The value of the average daily mass in kg/d of dry-filtered…

Q: A tie bar 50 mm x 8 mm is to carry a load of 80 kN. A specimen of same quality steel of cross-…

A:

Q: 01. The field capacity and permanent wilting point for a given 0.8 m root zone soil are 35% and 10%…

A: Given-Field capacity FC=35%,PWP=10%,root zone depth = 0.8 msoil moisture=20%depth of water = 250…

Q: A sample of dry soil is coated with a thin layer of paraffin and has a mass of 450 gm. It displaced…

A:

Q: The total degree of static indeterminacy of truss shown below is

A:

Q: Problem 2 An A36 channel section is used as a purlin in a roof system with spacing of trusses at 4.5…

A: Dead load, DL = 1.2 kN/m2Live load, LL = 1.4 kN/m2Take windward, L= 0.72 kN/m2A36 steel grade - fc =…

Q: The deflection and slope at C will be (take EI = 12000 kNm²) ^A 24.KN ¸60 kNm O

A:

Q: Using the slope deflection method, sketch the bending moment and shear force diagrams of the portal…

A: To analyze the given frame if support E sinks by 6mm.Note: Support A is considered as hinge support…

Q: What is the total thickness of a wall having 3/8 inch first siding, 2/8 inch rough siding, 3 3/4…

A: Thickness of first siding, Thickness of rough siding, Thickness of studs, Thickness of lath,

Q: Calculate Superelevation for a horizontal cure with redius 300mand wides 8m. the design speed 50…

A: Radius of curve (R) = 300m Width (B) = 8m Design speed (V) = 50 km/h Centrifugal ratio = 1/10…

Q: The moisture content of soil in the root zone of an agricultural crop at certain stage is found to…

A:

Q: Draw the influence line of the following quantities: (a) RA (b) MA (c) MB (c)VB A 3m B C 2m

A:

Q: What is difference of the average shear stress at the bottom and the sides of a rectangular flume…

A:

Q: The cylinder is confined by the brake as shown in (Figure 1), where μ = 0.4. The spring has a…

A: Torque, T = 800 N.mUnstretched length, L = 60 mmCoefficient of static friction () = 0.4Spring…

Q: What is the main goals of green architecture and how can an architect or group of architects…

A: Green architecture, also known as sustainable architecture or eco-friendly architecture, seeks to…

Q: The system given in Figure 5, the mass (m) is 30t, the lateral stiffness (k) is 3000kN/m, the story…

A:

Q: If the coefficient of variation of rainfall values at 4 rain gauge stations is 30% and permissible…

A: Coefficient of variation of rainfall Cv=30%Rain gauge stations n=4Permissible error in the…

Q: A field channel has cultivable commanded area of 2000 hectares. The intensities of irrigation for…

A: A field channel-Cultivable command area-CCA=2000 ha,Intensity of irrigation for wheat…

Q: A 240 mm E B 192 mm 30°

A:

Q: he insulation to be used in a certain slot is as follows: fish paper 3/64 inch, Tufflex 3/32 inch,…

A: Fish paper: 3/64 inchTufflex: 3/32 inchVarniches cambric: 3/64 inchTop stick: 1/8 inchTo find: the…

Q: Q Calculate the diameter and discharge of a circular sewer laid at a slope of when it is running…

A:

Q: 4.3 Based on the information given in the following table and for each assigned problem, calculate…

A: Mu = 327 k-ftb = 50 inbw = 14 int = 3 ind = 13 infc = 3 ksify = 60 ksiTo find:  The tension steel…

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.