1. Check the beam shown for compliance with the AISCS. Lateral support is provided only at theends, and A992 steel (E345 MPa and Fu= 450 MPa). The only uniform service dead load is theweight of the beam. The 70 KN service loads are 30%DL and 70%LL. Use LRFD.IR₁0.90m70,KN*W14 x 681.20m70 KN*0.90mR₂W14x6870 KN

Load=70 Sin =70*(4/5) =56 KN =12.58 kipsDead Load=30% of 12.58=3.78 kipsLive…

Check the beam shown for compliance with the AISCS. Lateral support is provided only at the ends, and A992 steel (E345 MPa and F₂= 450 MPa). The only uniform service dead load is the weight of the beam. The 70 KN service loads are 30%DL and 70%LL. Use LRFD. 70 KN 70 KN 14 70 KN

Check the beam shown for compliance with the AISCS. Lateral support is provided only at the ends, and A992 steel (E345 MPa and F₂= 450 MPa). The only uniform service dead load is the weight of the beam. The 70 KN service loads are 30%DL and 70%LL. Use LRFD. 70 KN 70 KN 14 70 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 11. An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, Bf=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of τ= 100 MPa on shear, for bearing, σb=200 MPa on single sheer, σb= 260MPa on double shear. 3. Determine the maximum allowable moment, M(all) in kn-m, base on the beam's cross-section. 4. Determine the location of the maximum moment on the beam in meters.
Situation 11. An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, Bf=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of τ= 100 MPa on shear, for bearing, σb=200 MPa on single sheer, σb= 260MPa on double shear. 7. Determine the maximum shearing stress on the beam in MPa. 8. Determine the flexural stress, In MPa, on the fiber 30mm above NA at distance 1m from A
Situation 11. An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, Bf=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of τ= 100 MPa on shear, for bearing, σb=200 MPa on single sheer, σb=260MPa on double shear. 1. Determine the location of centroid, y, from top of the beam in mm .
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear Determine the location of centroid, y, from top of the beam in mm Determine the moment of inertia, I, of the section in mm^4. Determine the maximum allowable moment, M(all) in kn-m, base on the beam's cross-section. Determine the location of the maximum moment on the beam in meters. Determine the maximum moment, in kN-m, on the beam Determine the maximum flexural stress on the beam in MPa.
Question (1): A rectangular beam has a width b = 400 mm, and effective depth d = 850 mm and a total height h = 900 mm. The beam is subjected to an ultimate moment Mu = 1500 kN.m and an ultimate shear force Vu = 700 kN. 1- ) Design the beam for flexure to calculate the required area of steel. 2-) Using stirrups Φ 10 mm ( No.10) diameter, calculate the required spacing (s) between the stirrups at the ultimate shear force section. For all questions, Use f’c= 28 MPa and Fy= 420 MPa
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. 2. Determine the moment of inertia, I, of the section in mm^4.
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. Determine the maximum flexural stress on the beam in MPa. Determine the maximum shearing stress on the beam in MPa.
A cantilever of rectangular section is 70 mm wide and 250 mm deep at the fixed end andtapers uniformly to 75 mm wide and 100 deep at the free end. The projecting length is1800 mm, and there is a load of 1800 N at the free end. Calculate the deflection of thefree end and the maximum bending stress. Take E = 14000 N/mm2. The cantilever is madeof timber.
Determine the safe span that a 100 * 150 mm purlin would have if it has a spacing 800 mm on centers, to carry a roof load of 60 Pa and a wind load of 1.4 kPa acting on the vertical surface. Allowable bending stress is 10 MPa and the allowable horizontal shearing stress is 0.4 MPa. The allowable normal deflection is 1/360 of span. Weight of purlin is 5 kN/m3 and E= 17.3GPa
The column shown has a uniform rectangular cross-section. b = 14 mm and d = 24 mm. Assume both ends A and B are pinned supports.This Column ACB is laterally braced at its midpoint C suchthat rotation is allowed but translation is prevented alongthe y-axis direction.Use E = 200 GPa, and assume L = 600 mm.Knowing that a factor of safety of F.S. = 3.3 is required andusing Euler’s formula, determine the largest allowablecentric load Pall that can be applied to the column.
Compute for the force in members FH, GH, and GI (USE METHOD OF SECTIONS) *For load P, take the last digit of your ID number example: ID # : 2187525, then P= 5 kN IF ZERO IS THE LAST DIGIT, TAKE THE 2ND TO THE LAST DIGIT example: ID #: 2187520, then P= 2 kN
A rectangular beam has the following properties: fc'=28MPa fy=270MPa b=300mm d=450mm As=4 of 36mm diameter bars Compute For: 1.) The magnitude of the ultimate moment capacity is Blank 1 kN.m 2.) If the fc' is reduced by 50%, the depth of the concrete stress block is Blank 1 mm.