A simply supported rectangular beam of length 6.45m has a width of 437.5mm and an effective depth of692.5mm. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of31 kN/m and 39.5kN/m., respectively. f'c = 28fy = 4201. Calculate the ultimate moment capacity of the beam.2. Calculate the height of the equivalent stress block.3. Determine the number of bars required for this beam

A simply supported rectangular beam of length 6.45m has a width of 437.5mm and an effective depth of692.5mm. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of31 kN/m and 39.5kN/m., respectively. f'c = 28fy = 4201. Calculate the ultimate moment capacity of the beam.2. Calculate the height of the equivalent stress block.3. Determine the number of bars required for this beam

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

A billboard 3m high by 4m wide is supported as shown in the figure. The totl weight of the billboard is 30 kN. H = 1.5 m and tetha= 60 degrees. Wimd pressure, q= 1.6 kpa Wind pressure coefficient = 1.0. Determine the reactions at the support.
A hollow shaft with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 76 kN and torques TB = 15 kN-m and TC = 4 kN-m, which act in the directions shown. Determine the normal stress x at point H.
NO. 4. The 150-kg bucket is suspended from end E of the frame. Determine the average normal stress in the 6- mm diameter wire CF and the 15-mm diameter short strut BD IN Figure 4.
The cantilever beam is subjected to a concentrated load of P=20kips. The cross-sectional dimensions of the rectangular tube shapre are b=5.2in , d=8.10in , and t=0.400in. Determine:a) The magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer in ksi, rounded-off to 2 decimal places.b) The magnitude of the shear stress at point K, which is loacted to the left of the vertical centroidal axis zK=1.1in. Answer in ksi, rounded off to 2 decimal places.
The bar has a 140 mm by 20 mm rectangular cross section. If P = 190 kN, determine the force components perpendicular (N) and parallel (V) to a-a, the inclined surface area, and the normal and shear stress magnitudes acting on surface a-a.
A couple M of moment 8 kN·m acting in a vertical plane is applied to a W200 * 19.3 rolled-steel beam as shown. Determine (a) the angle that the neutral axis forms with the horizontal plane, (b) the maxi-mum stress in the beam
In the weight wall support system given below, the internal friction angle of the sand ground behind the wall is 35 degrees and the beta angle is 20 degrees, the friction angle between the wall and the ground is 10 degrees, and the angle of inclination with the horizontal on the ground side of the wall is 82 degrees. In addition to these, the natural unit weight of the floor behind the wall is 15 kN / m.. According to this information, in order for the active resultant force on the wall to be 248 kN / m, how many meters should the wall height be? For the correct answer, the margin of error will be considered as 0.5. please fast
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
The solid circular shaft is subjected to an internal torque of T= 6.0 kN.m. Determine the shear stress developed at point A and B
QUESTION 2) A bending moment of M=4 kNm, tan alpha (α)=0.577, acts on the section in the figure. Unbiased Determine the position of the axis and draw the stress distribution in the section
P = 49 kips Determine the normal and shearing stress at point a, b, and c
A. Determine the maximum bearing stress in MPa if P = 115 kN. B. Determine the maximum shear stress in MPa if P = 115kN. C. Determine the maximum tensile stress in MPa if P = 11 kN.