5. The compound pulley shown has a centroidal mass moment of inertia of 40 N.m.sec?. determine the following: a) The angular acceleration of the pulley. b) The tension in the cord supporting the 700N weight. c) The tension in the cord supporting the 1700 N weight. 3m 1m Ia T2 a;=3a az=1(@) I 700 N 1700 N

5. The compound pulley shown has a centroidal mass moment of inertia of 40 N.m.sec?. determine the following: a) The angular acceleration of the pulley. b) The tension in the cord supporting the 700N weight. c) The tension in the cord supporting the 1700 N weight. 3m 1m Ia T2 a;=3a az=1(@) I 700 N 1700 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 100-mm-diameter pulley shown fits loosely on a 10-mm-diameter shaft for which the coefficient of static friction is Determine the minimum tension T in the belt needed to (a) raise the 100-kg block and (b) lower the block. Assume that no slipping occurs between the belt and pulley and neglect the weight of the pulley Choices: A. TMAX = 1075 N, TMIN = 906 N B. TMAX = 1075 N, TMIN = 690 N
1. How much work UP is done by the force P = 45 N on the collar?UP = _______N·m 2. How much work Ug is done by gravity on the collar?Answer: Ug = ______ N·m 3. Determine the speed of the collar as it passes position B.v =______ m/s
Consider two blocks connected . BlockA has mass 2.00 kg, and block B has mass 5.00 kg. The table on whichB sits is frictionless, the cord connecting the blocks is light and flexible,and the pulley is light and frictionless. The horizontal force F S hasmagnitude F = 20.0 N, and block B moves to the left with an accelerationof 1.50 m/s2. What is the coefficient of kinetic friction that one block exerts on the other?
The slotted arm OA rotates about a fixed axis through O. At the instant under consideration, θ = 32°, θ˙ = 47 deg/s, and θ¨ = 21 deg/s2. Determine the magnited of the force F applied by arm OA and the magnitude of the force N applied by the sides of the slot to the 0.3-kg slider B. Neglect all friction, and let L = 0.64 m. The motion occurs in a vertical plane.
: Block B has a mass m and is released from rest when it is on top of cart A, which has a mass of 3kg. Determine the tension in cord CD needed to hold the cart from moving while B slides down A. Neglect friction. =30o
Properties: • b1 = 300 mm • b2 = 180 mm • d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa • fy = 414 MPa • eccentricity = 200 mm Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in kN 4. Moment Capacity in kN-m
Replace the loading system by an equivalent resultant force and couple moment acting at point ?. Length AB = 1m Length BC = 2m F1 = 80 N F2 = 60 N F3 = 120 N Angle with respect to x-axis = 32 degrees Moment couple = 195 Nm
An experimental device imparts a force of magni tude F = 225 N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the moments of the force F about point 0 and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment.
Calculate the value of the deflection at point B due to concentrated load P in the form Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
4. An aerial copper wire (E =1x 10 5 N/mm ^2) 40 m long has cross sectional area of80 mm2 and weighs 0.6 N per meter run. If the wire is suspended vertically, calculatethe maximum weight which this wire can support at its lower end if the limiting valueof stress is 65 N/mm 2.a. 4627 Nb. 4281 NC. 4519 Nd. 5188 N
Situation 1: A beam whose moment of inertia is 0.0036 m4 at portion CB and E = 220 GPa is subjected to a load of intensity q = 20 kN/m and L = 6 meters. 1. If support B is removed, Calculate the deflection at point B. 2. If support B is present, Calculate the value of reaction at support B. 3. Calculate the deflection at point C if support B is present.
The 14.6 lb lever OA with 9.6 in radius of gyration about O is initially at rest in the vertical position (?= 90°) where the attached spring of stiffness k = 4.3 lb/in is unstretched. Calculate the constant moment M applied to the lever through its shaft at O which will give the lever an angular velocity ? = 5.9 rad/sec as the lever reaches the horizontal position ? = 0.