The roof of a single-story storage building shown is subjected to a uniformly distributed load of 2.4 kPa over its surface area. Beam BE is simply supported. Likewise, girders AC, CF, FD and AD are simply supported on columns A, C, F, and D. Girder Floor beam Column B I -64 6 m E -2 at 4 m = 8 m- Which of the following most nearly gives the maximum bending moment (kN-m) in beam AC?

The roof of a single-story storage building shown is subjected to a uniformly distributed load of 2.4 kPa over its surface area. Beam BE is simply supported. Likewise, girders AC, CF, FD and AD are simply supported on columns A, C, F, and D. Girder Floor beam Column B I -64 6 m E -2 at 4 m = 8 m- Which of the following most nearly gives the maximum bending moment (kN-m) in beam AC?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

The floor system of a factory consists of a 5”-thick normal weight reinforcedconcrete slab resting on four steel floor beams (A = 14 in2) that, in turn, aresupported by two steel girders (A = 40 in2), as shown in the plan below.a. Should this slab be idealized as one-way spanning or two-way spanning?b. Draw the free-body diagram for the dead loads on beam BF and label themagnitude of all loads.c. Draw the free-body diagram for the dead loads on girder AD and label themagnitude of all loads.d. What is the axial load carried by column A?
2.) The Pratt roof trusses are uniformly spaced every 3.60 m. The deck, roofing material, and the purlins have an average weight of 0.15 kN/m^2. The building is located in the hills where the anticipated wind load is 2.10 kN/m^2. The wind load is assumed act perpendicular towards the top chord of the roof (side AHG only). Considering the given loads, determine the following: a.) Equivalent concentrated load on Joint A, H, G, F and E due to dead load b.) Equivalent concentrated load on Joint A, H and G due to wind load c.) Force in each member due to dead load and wind load. Neglect the weight of the truss members and assume A is pinned and E is a roller
a) What maximum nominal moment can the beam carry if it is to be designed as a singly reinforced beam, in kN-m? b)What is the required tension steel area in mm2, at point of maximum positive moment? c)What is the required tension steel area in mm2, at point of maximum negative moment?
The balcony located on the third floor of a motel is shown in (Figure 1). It is constructed using a 4-in.in. -thick concrete (plain stone) slab which rests on the four simply supported floor beams, two cantilevered side girders AB and HGHG, and the front and rear girders. The idealized framing plan with average dimensions is shown in (Figure 2). According to local code, the balcony live load is 45 psf. Assume the front girder is a channel that has a weight of 25 lb/ft and the side girders are wide flange sections that have a weight of 45 lb/ft. Neglect the weight of the floor beams and front railing. For this solution treat each of the five slabs as two-way slabs. Follow the sign convention. Part A: Draw shear and moment diagram for girder AB. Part B: Draw shear and moment diagram for girder BG.
Consider a two-bay building frame ABCDEF, with A, B, and C as fixed supports, AD, BE, and CF as columns, and DE and EF as girders. Span DE is 9.2 meters long and span EF is 7.8 meters long. The columns have a height of 5.25 meters. Assume that the columns have same cross-sections. A wind-induced lateral load of 80 kN is applied at D, pointing towards the structure. Additionally, a-wind induced uniform load of 1,5 kN/m, pointing upwards, is applied at the girders. (a) Draw the free-body diagram of the structure. (b) Draw the shear and moment diagram of the girders considering the uniform load only using approximate methods. (c) Determine the support reactions considering all applied loads using approximate methods, For lateral load analysis, use portal method.
A horizontal steel girder of uniform section, 15 m long, is supported at its extremities and carries loads of 120 kN and 80 kN concentrated at points 3 m and 5 m from the two ends, respectively. I for the section of the girder is 1.67 x lO-3 m' and E = 200 GN/m2. Calculate the deflections of the girder at points under the two loads. (Cambridge)
The floor system shown carries a live load of 4.80kpa live load and 100mm thick concrete slab. Let point A and Point C be pin and roller support, respectively and determine the: A. Maximum factored loadings at girder ABC. Note that beams AD,BE and CF transmits its load to girders ABC and DEF. B. Determine the shear equation of girder ABC
Refer to figure CD and DE of the gable frame shown are subjected only to vertical loads only along their lengths. What is the maximum moment at CDE in kN-m?
Determine the crippling load for the “T”section of length 5m when it is used as a strut with both ends hinged. E=2.0x105 N/mm2
A rigid beam ABC is supported at C by a pin support, and at A and B by timber struts AD and BE which are in turn supported by pin supports at D and E respectively (Figure 1). The struts AD and BE are constructed using F11 timber (refer Figure 2) with square cross section 40 mm x 40 mm. A uniformly distributed load of 10 kN/m acting horizontally to the right is applied along the complete length ABC. Under the action of this load, in addition to any changes in the lengths of the struts, the pin support at C settles by 1 mm to the right. Assume that the beam and struts are weightless and that the struts will not buckle. (a) Using equilibrium and compatibility considerations determine the support reactions at C, D and E. Hint: Since the struts AD and BE can transfer only axial force, the reactions at D and E act horizontally (that is, there are no vertical reaction components at D and E). (b) Find the normal stress, normal strain and change in length of strut AD.
A small balcony constructed of wood is supported by three identical cantilever beams (see figure). Each beam has length L, = 2.3 m, width b, and height h = 3b/2. The dimensions of the balcony floor are L, x L2, with La = 2.7 m. The design load is 6.5 kPa acting over the entire floor area. (This load accounts for all loads except the weights of the cantilever beams, which have a weight density y = 6.5 kN/m^3 --) The allowable bending stress in the cantilevers is 45 MPa (a) Assuming that the middle cantilever supports 50% of the load and each outer cantilever supports 25% of the load, determine the required dimension b. Round to the nearest whole number. mm (b) Assuming that the middle cantilever supports 50% of the load and each outer cantilever supports 25% of the load, determine the required dimension h. Round to the nearest whole number. h = mm
Consider the following framing plan below. Squares labeled A through L are columns. All girders have rectangular sections with width 300 mm and depth 600 mm. Slab thickness is 125 mm. Superimposed dead load for the entire floor is 2.95 kPa and live load for the entire floor is 4.8 kPa. For self-weight of the floor system, use unit weight of RC of 23.6 kN/m3. a. Considering continuous girder DEF, determine the maximum factored positive & negative moments Mu (+) & Mu (-), as well as the factored shear Vu that should be used for the design of the said girder. Use ACI moment & shear coefficients to draw the factored shear & moment diagram of the said girder.