Problem #1. The 60-mm diameter shaft is subjected to torques as shown. If the applied allowable torque T in Kn-m. Check if the shaft satisfies the allowable shear stress and angle of twist limitations. The allowable shear stress is 80 MPa and the angle of twist of disk A relative to disk C is limited to 0.06 rad. The shaft is made of aluminum with the following properties: Elastic Modulus, E = 70 GPa and Shear Modulus, G = 25 GPa. Show complete solution (FBDs and equilibrium equations). 1.20 m D A T = 5.xy kN-m where xy are the last two digits of your ID# (Example: ID# = 1234567, then T=5.67 kN-m), T C 1.20 m T

Problem #1. The 60-mm diameter shaft is subjected to torques as shown. If the applied allowable torque T in Kn-m. Check if the shaft satisfies the allowable shear stress and angle of twist limitations. The allowable shear stress is 80 MPa and the angle of twist of disk A relative to disk C is limited to 0.06 rad. The shaft is made of aluminum with the following properties: Elastic Modulus, E = 70 GPa and Shear Modulus, G = 25 GPa. Show complete solution (FBDs and equilibrium equations). 1.20 m D A T = 5.xy kN-m where xy are the last two digits of your ID# (Example: ID# = 1234567, then T=5.67 kN-m), T C 1.20 m T

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The stepped shaft ACB shown in Figure bellow is fixed at both ends and loaded by a torque TO at point C. Segment AC having solid circular cross section and segment CB having hollow circular cross section. If the shafts material is steel with shear modulus G = 11 x 10°psi, and the torque is To = 8,000 lb-in. Calculate: (a) The maximum and the minimum shear stress in segment CB. (b) The maximum and the minimum shear strain in segment CB. (c) The angle of rotation 0, at the cross section where the torque To is applied.
A solid 1.500-in.-diameter steel [G = 12,000 ksi] shaft is subjected to torques TB = 270 lb-ft and TD= 95 lb-ft, acting in the directions shown. Assume a = 54 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 12 ksi, determine the maximum torque TC that can be applied to the shaft.
A solid 1.250-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 295 lb-ft and TD= 95 lb-ft, acting in the directions shown. Assume a = 48 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 14 ksi, determine the maximum torque TC that can be applied to the shaft. [Answer: TC = 542 lb ft]
A hollow shaft shown with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 75 kN and torques TB = 16 kN-m and TC = 7 kN-m. 14. Calculate the polar moment of inertia of the section in mm4.1 15. Calculate the absolute value of the internal torque at H in kN.m. 16. Calculate the torsional shear stress at H in MPa. 17. Calculate the absolute value of the minor principal stress at point H in MPa. 18. Calculate the absolute value of the major principal stress at point H in MPa. 19. Calculate the absolute value of the maximum shear stress at point H in MPa. 20. Calculate the orientation of the principal axes in degrees. Kindly answer all numbers with complete solution
A solid 1.750-in.-diameter steel shaft is subjected to torques TB = 285 lb-ft and TD= 115 lb-ft, acting in the directions shown. If the allowable shear stress in the shaft is 22 ksi, determine the maximum torque TC that can be applied to the shaft.
A solid constant-diameter circular shaft is subjected to the torques of TA = 460 lb·ft, TB = 1000 lb·ft, TC = 880 lb·ft, and TD = 340 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6. (b) If the allowable shear stress in the shaft is 7200 psi, what is the minimum acceptable diameter for the shaft?
The steel tube seen below has an outer diameter do = 60mm and an inner diameter d, = 50mm. It is subjected simultaneously to torque T = 1.5kN-m and to axial load P = 205kN. Determine: (a) the maximum in-plane shear stress and its orientation, (b) the associated normal stress and (c) sketch both on a properly oriented element.
The engine of the helicopter is delivering 600 hp to the rotor shaft AB when the blade is rotating at 1200 rev/min. Determine the diameter mm of theshaft AB if the allowable shear stress is 75 MPa and the vibrations limit the angle of twist of the shaft to 0.05 rad. The shaft is 2 ft long.
Question-04: Solve for the torque T that can causes a maximum shearing stress of 4.2 ksi in the cylindrical steel shaft as shown in Figure 3. Assume radius of the shaft r = 1.2inches.
A compound steel (G = 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm-diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to φC≤ 4.6°. Assume L1=0.6 m and L2=1.0 m. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in N-m rounded to three significant digits.
A solid 0.78-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (3). a.)3.86 ksi b.) 3.51 ksi c.) 3.15 ksi d.) 5.38 ksi e.) 4.85 ksi
A bearing pad is a device which is used to support a bridge or other heavystructure in a way that permits the load to shift slightly in a horizontal directionrelative to the ground or foundation. If a horizontal force af 528 kN is applied tothe top surface of the bearing pad, and that a = 700 mm, b = 550 mm, h = 75m and the modulus of elasticity G = 1.25 MPa. Determine the following: a. The average shear stress on the bearing pad.b. The horizontal displacemant of tne bearing pad. Note: Draw the Free Body Diagram, include the proper units and round-off the answers to 3 decimal places.