(3) 24 B Bean AB A Beam AB. 301 G 4#8 12" 24' -#4 24" Given fé= 3 ksi Grade 60 steel NWC. COVER = 1.5" #4 stirrups. DL= 70 psf, not including self-weight. LL = 40 psf. (No Live Load 4 # 8. b=12", h=24", Reduction Check (5) Check if the section is properly designed to resist the max. bending Mu ? (6) If Not, please redesign

(3) 24 B Bean AB A Beam AB. 301 G 4#8 12" 24' -#4 24" Given fé= 3 ksi Grade 60 steel NWC. COVER = 1.5" #4 stirrups. DL= 70 psf, not including self-weight. LL = 40 psf. (No Live Load 4 # 8. b=12", h=24", Reduction Check (5) Check if the section is properly designed to resist the max. bending Mu ? (6) If Not, please redesign

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.7.3P

See similar textbooks

Similar questions

Problem 1. A W30 x 116 beam hasthe top flange restrained againstlateral displacement and rotationand has an unstiffened web. A pointload is applied to the top flange at2m. From the left support. The beamspans 12 m. Use A36 steel with yieldstrength of Fy = 248 Mpa. a. Compute the maximum value of point loadthat may be applied without web yieldingoccurring. b. Compute the maximum value of point loadthat may be applied without web cripplingoccurring. Properties of W30 x 116d = 762 mmK = 41.28 mmbf = 266.7 mmtf = 21.59 mmtw = 14.33 mm
Design an axially loaded Round spiral column: PD = 500 kN PL= 650 kN f’c= 35 Mpa fy = 420 MPa. Initially assume ρg = 0.03. Use 25 mm diameter main bars. Use 12 mm dia. ties with fyt = 276 Mpa. Concrete cover is 30mm. Provide section drawing.
A spiral column is to carry a dead load 800 kN and a live load of 1350 kN. If 2% of the main bars is desired, how many reinforcing steel bars are needed and the spacing of the spiral? f'c = 27.6 MPa fy = 414 MPa Main bars = 25 mm diam. Spirals = 10 mm diam. Concrete Cover = 30 mm
QA Fora flow rate of 300 iter/second ata velocity of 1.3 meters/secand, design a seamless. steel Take factor of safety of 2.5, Longitudinal efficiency ofjoint, 1 = 0.50, and intesnal pressure= 4 Nl
The beam is simply supported on a span of 6 m and carries a load of 18 KN/m. Use ACI Specifications withfc’ = 17.2 MPa, fs = 124 MPa, n = 12, d’ = 65 mm, and ?concrete = 23.54 KN/m3.(a) service moment (f) use b = 250 mm, d = Answer (round down to nearest 25 mm) + 50 mm(b) fc to take care of dead load(c) k (g) h (h) dead load (i) total load(d) j (j) recompute service moment (k) check effective depth(e) R (l) use 28mmɸ for As (m) check main bar clear spacing
Channel sections are used as a purlin. The top chords of the truss are sloped at 5H to 2V. Trusses are spaced 5m on centers and the purlins are spaced 1.4m on centers. Use the properties of the channel section given below. Loads: (Consider all loads pass thru the centroid of the section.) Dead load = 750 Pa Live load = 1,000 Pa Wind load = 1,400Pa Wind coefficients: Windward = 0.3 Leeward = -0.5 Use Fbx=Fby=250 MPa. Determine the maximum value of the interaction equation using the load combination of 0.75(D+L+W)
A reinforced concrete beam having a width of 250 mm, effective depth of 350 mm, and d’= 65 mm is to be designed for service moment of 20 Kn m and 35 KN m correspondinglyfor dead load and live load. Use fc’ = 20.7 MPa and fy = 275 MPa. Provide the following(a) Mu (b) Rn(c) ?, ? min, and ? max(d) As (e) a & c (f) check if steel yields(g) ?steel (h) type of failure (i) A16
Problem 2: The loads on a roof beam consist of a dead load of 0.2R kN/m, a roof live load of0.13R kN/m, and a snow load of 0.14R kN/m. Apply allowable strength design approach todetermine the required load capacity (required strength) to be used in the design of thecolumn. Which AISC load combination controls? NOTE: use R=922
The rigid pipe is supported by a pin at A and an A-36 guy wire BD. If the wire has a diameter of 0.25 in., determine the load P if the end C is displaced 0.075 in. downward. (The answer in the book is 570 lb. Please provide solution.)
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
The framing plan of the flat roof of a gymnasium is shown. De- termine the design free-body dia- gram of beam A-B. There are no joists on the roof system. Dead load is D = 20 lb/ft2. Check load combi- nation number 2 [L.C.2] only. Dis- card rain R and snow S loads in your analysis.