Answered: Complete the notes, find the elevation…

Complete the notes, find the elevation of point A and state the error in the network. Determine the order of error if each course is 300 feet in length.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A cylinder having a diameter of 6 in (152mm) and a stroke length of 25 in (635mm). The exit time…

Q: Using Macaulay's method, determine maximum deflection in the beam. El = 41000 kN.m².

A: The Maximum Deflection in the Beam using MACAULAY METHOD of double Integration ###

Q: A municipal wastewater flow of 1,000 m³/d contains 400 mg/L BOD5 and is treated to be in a trickling…

A: The design of a trickling filter involves 1.the determination of the required filter 2.media surface…

Q: SITUATION 4 If downward seepage occurs on the same slope from Situation 3, determine H. Specific…

Q: Draw the shear and bending moment diagrams for the beam and loading shown, and determine the maximum…

A: A beam is given we need to draw shear force and bending moment diagram

Q: Following observations were made to determine sensitivity of two bubble tubes A and B. Find which is…

Q: Question A horizontal pipe of non uniform cross section has water flow through it such that the…

Q: A soil sample has a shrinkage limit of 10% and specific gravity of soil solids is 2.7. The porosity…

Q: 2. A beam with an inverted U section is loaded as shown. What is the max flexural stress developed…

A: Given: Required : Maximum flexural stress and shear stress

Q: A block of wood 2 m long, 2 m wide and 1 m deep is floating horizontally in water. 3 If density of…

A: Block dimensions- Length L=2 m, Width b=2 m, Depth h=1 m, Density of wood ρwood=800 kg/m3, To Find-…

Q: QUESTION 20 Transportation of construction materials may lengthen a project by a year. True False…

Q: If the total area of the comfort room is 36.75m2. What should be the number of exhaust fans, and how…

Q: A metal bar of 10 mm diameter when subjected to a pull of 23.5 kN gave an elongation of 0.3 mm on a…

A: Diameter d=10 mm Force F=23.5 kN Elongation=0.3 mm Gauge length l=200 mm It is needed to find the…

Q: a storm of 3 hours duration has rainfall intensities of 30 mm/h for the first hour, 50 mm/h for the…

Q: Q.5) For a sand sample the values of the minimum (emin) and maximum void ratio (e....) are 0.42 and…

Q: The pre-cast T-beam has the cross-section shown. Determine its weight per meter length if it is made…

Q: F6-2. Determine the force in each member of the truss. State if the members are in tension or…

A: To find: The forces in each member for the given truss.

Q: The figure shows the soil profile at a site where you plan to lower the water table. You have…

Q: how esv change with increase or decrease with contractility?

A: ESV (End-Systolic Volume) is the volume of blood remaining in the ventricle at the end of systole,…

Q: A masonary dam has pervious sand as foundation. determine the maximum permissible upward gradient.…

A: Factor of safety FOS=4 Porosity n=45%=0.45 G=2.70 It is needed to find the maximum permissible…

Q: An Engineer measured the distance between two locations on a plan having a scale of 1 cm = 50 m as…

A: Wrong scale- 1 cm=30 m Correct scale - 1 cm=50 m Measured distance=600 m It is needed to find the…

Q: Assuming a circular watershed with radius 900km has its center at the origin. The rain gauges are…

A: Total number of rain gauges (m) = 5 The rainfall depth recorded at 5 stations are Station ARG1…

Q: Draw Mode shapes for the system shown in figure m3-50000 kg m₂=55000 kg m₁=60000 kg k3=30000 kN/m…

Q: SITUATION 3 Determine the height of the infinite slope, H, such that the factor of safety of 3.1 is…

A: Slope - Infinite The factor of safety, FOS = 3.1 The angle of slope with respect to horizontal, β =…

Q: 17-6. Solve Prob. 17-5 if the column is pinned at its to and bottom. - 300 mm 10 mm 10 mm 200 mm 10…

Q: A square footing 2.5m x 2.5 m supports a square column 300mm x 300mm at its center. Concrete cover…

A: A square footing 2.5m x 2.5 m dimension supporting a square column 300mm x 300mm. Dead Load=680 kN…

Q: Select the lightest 2L (LLBB) section that will resist a service tensile load, D=735 KN and L-980…

Q: A rigid bar, hinged at one end, is supported by two identical springs as shown. Each spring consists…

Q: A circular shape land has an area of 122.718cm² on a map having a scale 1/500. What is the area of…

Q: O From the given trusses determice all the forces carried by each member the trusses shown: of 4 kn…

Q: Question A horizontal pipe of non uniform cross section has water flow through it such that the…

A: Pressure at a point P1=40 kPa, Velocity V1=2 m/s, Velocity at point 2, V2=3 m/s, It is needed to…

Q: A toy is dropped into a pool of water (g = 9.81 = 9.81 m2, p = 1000 m). It is then submerged 3m.…

Q: The true length of a line is known to be 200 m. When this is measured with a 20 m tape, the length…

A: True length of line L = 200 m Measured length L' = 200.80 m Actual length of tape AL = 20m It is…

Q: gives a cross section of a concrete dam. The subsoil is anisotropic and has in./sec and kv=2.0 x 10…

Q: Find the reactions at the wall, then give the shear and moment diagram for the following cantilever…

Q: A compression member is built up from a W14x90 and a W10x49, both of A992 steel. a. Compute rx and…

A: We need to first obtain the Moment of inertia about X and Y axis We can determine the moment of…

Q: A circular water tank is designed to store water for 78,500 liters capacity. The water tank rests on…

A: Capacity=78,500 litres Height H=4 m Diameter D=5 m W=specific weight of water=10,000 N/m3 It is…

Q: 300 lb B 4 ft 8 ft 600 lb 300 lb 8 ft 4 ft → E 6 ft PROBLEM 6.4 Using the method of joints,…

A: Given: Required : Member force

Q: Q.5) For a sand sample the values of the minimum (emin) and maximum void ratio (emax) are 0.42 and…

Q: SITUATION. Determine the reaction (kN) at spring support for the beam as shown below. A E=200,000…

A: E = 2 × 105 MPa I = 450 × 106 mm4 Determine the reaction at spring support (R).

Q: 1000 Ib

Q: 4 L Derive Elymax. (

A: This question is related to the Strength of the material from Civil Engineering. In this question ,…

Q: For the beam shown below, given that L = 7 m, and w=6 kN/m, draw the FBD, shear & momment diagram,…

A: Length of beam(L)=7m w=6kN/m

Q: 3 Determine the vertical displacement of Joint A by the Method Virtual Wok if member AE is…

A: The virtual work method is mainly related to a force that is acting on a particle or member of the…

Q: or the beam shown below, compute the moment area of the moment diagram about the left end.

A: Consider Moment equilibrium at D RA*6 = 12*950*3*33+1 RA = 475 N Consider vertical force equilibrium…

Q: Q.24 The evapotranspiration rate from the land and the oceans are observed as 3 82,000 km³/year and…

A: The evapotranspiration rate from the land = 82,000 km3/year, The evapotranspiration rate from the…

Q: A 3.5 m D 7m B 2.5m *

Q: In 1-2 sentences, explain why you think the Aor. Landfill in Clark County, Nevada was chosen as a…

A: explain why the Aor. Landfill in Clark County, Nevada was chosen as a location for the landfill ?

Q: Task 1: Question 2 The parking survey data collected from a parking lot by license plate method is…

Q: Calculate Reynold's number if a fluid ha 00 kg/m³ flows through a pipe of radiu

Concept explainers

Traverse Survey

Traverse surveying is a popular method of surveying. Traversing is that type of survey where several connected survey lines form a framework and the directions and lengths of the survey lines are measured with the help of a tool to measure angles and tape or chain respectively. Traverse networks involve placing survey stations in a queue or trail and using pre-tested points as a basis for looking at the next point. This type of surveying is different from Tacheometric surveying, where only angles are measured and the process of chaining is reduced.

Question

The following level network notes are handed to you by your boss at ABC Surveying,
Inc. All units are in feet.
Complete the notes, find the elevation of point A and state the error in the network.
Determine the order of error if each course is 300 feet in length.
STA
BM1
TP1
TP2
TBM "A"
TP3
BM1
Actual error=
BS
3.33
1.35
2.385
7.33
0.54
HI
FS
2.66
7.64
2.22
2.18
0.23
Elev
457.32
Description
Iron Pin Southwest of Main St.
Wooden Hub North of Fourth St
Iron Pin Southwest of Main St.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: formula used

VIEW

Step 2: calculataion

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A parcel of land has been surveyed in the field and the lengths and bearings of the various sides are shown: a. Compute the error of closure for the traverse. b. Compute the precision of linear measurement. Determine the included area (using DPD method) within the traverse in acres. LINES AB BC CD DA BEARINGS N53' 27' E $ 66' 54'E $ 29'03' W N 52'00' W T DISTANCES (m) 59.82 70.38 76.62 95.75
Q.3 A level circuit is shown in figure. The survey, needed for local engineering project, commenced at BM 35, the elevation of new benchmarks 36, 37, 38 and 39 were determined, and then the level survey was looped back to BM 35, the point of commencement. Fined the adjusted new BMs. ВМ 35 35 36 37 38 39 35 Elevation(m) | 185.000(fixed) 184.242 187.299 186.251 188.397 184.933 BM 36 0.9 km вм 35 0.8 km Фвм 37 0.8 km 0.6 km BM 39 вм 38 0.7 km
Please make me a unique problem about compound curve in surveying and please write the solutions and answers. Thank you!
4-) Complete the benchmark-leveling field notes by computing and recording the HI and elevation for each TP and Benchmark. Do the arithmetic check. STATION BS HI ES ELEVATION STATION BS HI FS ELEVATION BM1 2.367 200.00 BM1 3.784 150.00 1 0.345 1.277 1 1.451 0.278 2 1.128 3.785 2 0.555 2.123 3 0.978 0.426 3 2.354 0.754 4 2.127 0.785 0.750 1.075 BM2 3.945 BM2 2.102 BS FS BS FS
Elementary Surveying Instruction: Please show complete solutions for credit. Problem: a. If line DF is the closing line, find its length. b. Find the bearing of the closing line DF, rounded to the nearest minute. c. Find the bearing of course EF. d. Find the length of DE, rounded to the nearest tenth of a meter.
Q.3 A level circuit is shown in figure. The survey, needed for local engineering project, commenced at BM 35, the elevation of new benchmarks 36, 37, 38 and 39 were determined, and then the level survey was looped back to BM 35, the point of commencement. Fined the adjusted new BMs. BM 35 Elevation(m) 190.000(fixed) 35 39 186.397 35 190.033 36 37 38 188.242 186.299 188.251 BA 36 09 km. BM 35 O8 km DeM 37 0.8 km 06 km BM 39 BM 38 0.7 km
Given the tabulated measurement of the closed traverse as shown. Determine the area of the traverse using DPD Method. Line Length Bearing AB 413.600 m N 09°30’ W BC 304.380 m N 55°06’ W CD 407.210 m S 57°35’ W DE Unknown S 04°05’ E EA 649.630 m Unknown Note: EXPRESS YOUR ANSWER UPTO 3 DECIMAL PLACES.
Remote Elevation ated to the bounde You have been asked to determine the bottom of steel elevation for the Cuyahoga Valley National Bridge. (X marks the spot) The surveyors in the field obtained the following data by setting up a total station on a point of known elevation. Use ONLY the APPLICABLE DATA Height of Prism= Height of Surveyor= Height of Total Station= Elevation of known point A= Horizontal distance to prism= Vertical angle to bottom of steel= 4.37 ft. 6.11 ft. 5.75 ft. 1248.86 ft. 122.88 ft. 26°22' 26°22' Bridge Q
4. Lines of levels to establish the elevation of a point are run over four different routes. The observed elevations of the point with probable errors are given below. Determine the most probable value of elevation of the point LINE OBSERVED ELEVATION (m) PROBABLE ERROR (m) 1 219.832 +- 0.006 2 219.930 +- 0.012 3 219.701 +- 0.018 4 220.021 +- 0.024
Given the following tabulated data LENGTH LINE BEARING Determine the following: (m) S 06° 35' 1. Linear Error of Closure 1-2 445.66 W 2. Direction of the side of error N 17° 48' 2-3 326.73 W 3. Precision of the measurements made N 70° 59' 3-4 434.50 4. On your solution sheet, tabulate the E latitude and departure of each traverse line. S 59° 33' 4-5 427.00 E S 39° 18' 5-1 301.95 E
Bearing Angle Traverse Given the tabulated measurement of the closed traverse as shown. Determine the missing data. Line Length Bearing AB 589.060 m N 87°30’ E BC 291.860 m N 30°30’ E CD 656.980 m S 42°45’ E DE 654.060 m Unknown EA 686.660 m Unknown Note: EXPRESS YOUR ANSWER UPTO 3 DECIMAL PLACES. please be accurate in providing a proven solution, thank you.
A traverse has the following data: Upload LINE Choose a File AB BC CD DE EA LENGTH 33.48 Use compass rule in adjusting the closed traverse and compute for the Linear Error of Closure and Relative Error of Closure. 8.11 39.42 7.08 22.02 BEARING N 73°23' E $ 39°30' E S43°40' W N 39°50' W N 17°33' W