Compute the total net deflection of the simply-supported beam with the following properties listed below. (Include the sign if it is negative) Properties: Length = 6.82 m Width = 237 mm Depth = 407 mm eccentricity = 119 mm Ec = 14,433.67 MPa Prestressing Force = 402 kN Unit weight of concrete = 22.21 kN/m3

Compute the total net deflection of the simply-supported beam with the following properties listed below. (Include the sign if it is negative) Properties: Length = 6.82 m Width = 237 mm Depth = 407 mm eccentricity = 119 mm Ec = 14,433.67 MPa Prestressing Force = 402 kN Unit weight of concrete = 22.21 kN/m3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An overhanging beam supports the loads as shown in the figure. If El 3000.65 kNm², determine the value of deflection at point Fin millimeters.
A cantilever beam carries a trapezoidaldistributed load (see figure). Let wB = 2.5 kN/m,wA = 5.0 kN/m, and L = 2.5 m. The beam has amodulus E = 45GPa and a rectangular cross sectionwith width b = 200 mm and depth h = 300 mm.Use the method of superposition and Cases 1 and8 in Table H-1 to calculate the def lection and rotationat B.
If FB = 560 N and FC = 700 N, determine themagnitude and coordinate direction angles of the resultantforce acting on the flag pole.
For the given beam section, solve all the unknown support reactions. Also, using EI=20,000 N-m2, calculate the deflection on the point of application of the 2.5 kN-m moment load.
NEED ASAP, thank you! Using SLOPE DEFLECTION METHOD for the continuous beam below, determine the following structural parameters and support moments using unreduced rotational stiffness; 1. The value that most nearly gives the absolute value of Fixed-end moment (FEM) at joint B of member AB in kN-m, FEMBA 2. The value that most nearly gives the absolute value of Fixed-end moment (FEM) at joint B of member BC in kN-m, FEMBC 3. The value that most nearly gives the absolute value of the Moment at A in kN-m 4. The value that most nearly gives the absolute value of the Moment at B of member AB in kN-m, MBA
A cantilever beam 5 m long carries a concentrated load P at 3.75 m from the fixed end. ( E = 25 x 103 MPa, I = 1.6 x 109 mm4, P = 150 KN) What is the deflection under the load P? What is the maximum beam deflection? What is the upward force applied at the free end to prevent the beam from deflecting?
A 6m simply supported beam AB carries 2 concentrated downward loads of P=50KN each placed at third points of the beam span. With constant EI=21000 KN-m2. Using Double Integration Method (DIM) with origin taken at point A (left support) where 0 ≤ x ≤ 6m, calculate the first constant of integration, C1? Express your answer in KN-m2 in 2 decimal places.
Before the load P was applied, a gap, ?0(2.75mm) existed between the cantilever beam AC andthe support at B. Knowing that E=200 GPa, determine the magnitude of P for which thedeflection at C is δ(5.5mm) and the reaction at B. (Hint: Use the method of superposition and beam deflections in Appendix A)
Consider a 7-story buildings with a total plan area BxL. In which B=125ft and L=60ft . The average weight of each floor and roof are 95 Ib/ft and 75 lb/ft?, respectively. The 84 ft-tall building is located in a seismic region with SDs =1.6 g and SD1 =0.5g for a building supported on rock, where g is the gravitational acceleration. The structure of the building consists of steel moment frames (all joints are rigid) that have an R value of 8. The importance factor I=1.0 Determine the total design seismic force (kips) acting at the base of the building ( seismic base shear in kips). ***the answer was between 339.5 and 342.5*** but I don’t understand how . Handwritten work is preferred
From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m and EI = 200MNm^2Determine the following;C. Slope at L/3. D. Deflection at L/3.
Calculate the value of the deflection at point B due to concentrated load P in the form ??=??????????? Note: EI will cancel out in further calculations. Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
Using Unit Load Method. Determine the slope and deflection at point B of the beam shown if the figure. Let ? = 29x10^3 ksi and I= 800in^4.