Connect a 5*7 dot-matrix display to the 8051-microcontroller (Draw the schematic on paper). Then, display the content of variable NUMBER on the display, digit by digit every one second. for example if NUMBER=249, then "2" will be displayed for one second, after that digit "4" and finally digit "9" will be displayed for a whole second. Assume that the necessary lookup table exists in Memory at address OXFO00.

Connect a 5*7 dot-matrix display to the 8051-microcontroller (Draw the schematic on paper). Then, display the content of variable NUMBER on the display, digit by digit every one second. for example if NUMBER=249, then "2" will be displayed for one second, after that digit "4" and finally digit "9" will be displayed for a whole second. Assume that the necessary lookup table exists in Memory at address OXFO00.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Give an example of how to reduce the size of the translation table in flash storage, which is often used to convert very large ranges of consecutive logical page numbers into consecutive physical page numbers. Flash memory:
For our byte-addressable computer, we opted for a fully associative mapping that allows for 32 cache memory blocks and 16 bits for main memory addresses. If the size of each block is 16 bits, then the following is correct:Find out how many bytes the offset field takes up (a).(B) Measure the size of the tag field in pixels.
In MATLAB, a grey-scale image is stored a a matrix of numbers, all between 0 (black) and 255 (white). Since there are 256 possible values, 8 bits are needed or each pixel, in contrast to a normal integer, which is 64 bits.To save memory, grey-scale images are stored with a special data type, uint8 (unsigned 8-bit integer). In computer terminology, 8 bits = 1 byte. Even at one byte per pixel, a large image can consume a lot of memory. For example, a 1000x1000-pixel image takes 1 million bytes (which is a little less than 1 megabyte, since by convention 1 Mbyte = 2^20 bytes). One technique for reducing the size of an image is quantization - reducing the number of allowable levels from 256 to something smaller. Surprisingly, most images can be quantized by a large factor without losing much information. In this problem, you will quantize a grey-scale image to only 4 levels, so that it could (in principle) be stored as 2 bits per pixel. The template will read in an image file. Your job…
Consider a paging system with the page table stored in memory.a. If a memory reference takes 400 nanoseconds, how long does a paged memoryreference take?b. If we add TLBs, and 95 percent of all page-table references are found in the TLBs,what is the effective memory reference time? (Assume that finding a page-table entry inthe TLBs takes zero time, if the entry is there.)
Consider the image attached that represents part of the memory of a 16-bit address space that has an addressability of 2 bytes. In the von Neumann model, the contents of a memory location can also be interpreted as an instruction. E.) Interpret the contents at address 0x0C0E as an LC-3 instruction to determine the operation. (Enter either ADD, JMP, LDR, or OTHER if it is not one of the first 3) F.) Interpret the contents at address 0x0C0F as an LC-3 instruction to determine the operation. (Enter either ADD, JMP, LDR, or OTHER if it is not one of the first 3) A memory location can store an address. We call that memory location's contents a "pointer" since it's an address that "points" to another memory location. G.) Interpret the contents at address 0x0C0B as a pointer. (Enter hex like the following example: 0x2A3F) H.) What are the contents of the memory location that the pointer above is pointing to? (Enter hex like the following example: 0x2A3F) Another reference : LC-3…
Consider the following hexadecimal readout: 000000 8A00 8E00 CFA1 48BF 7900 3202 9015 AD34 000010 0218 6D30 028D 3402 AD35 0288 3102 8D35 000020 0E30 0290 DAEE 3102 4C00 0200 0040 004B Refer to the first byte of memory shown above, address 000000. Assume that this byte is used to store an 8-bit unsigned integer. What is the decimal value stored in this byte? Group of answer choices 138 -27 22,842 66
15. Consider the following Java-like code: int number = <<read number from user>>; int mask = MASK; int result = number OP mask; if (result != 0) { print("Bit 8 was set"); } The above code is supposed to print “Bit 8 was set” if bit 8 of user’s number was set to 1. If bit 8 was not set, then this code should not print anything (result==0). What hexadecimal value should MASK be, and what bit-wise operation should OP be, for the above code to work correctly?
Provide an example of how to minimise the size of the translation table in flash storage when very often vast ranges of consecutive logical page numbers are translated into successive physical page numbers. Flash storage:
25: . Find the time delay in the following program if the crystal frequency is 1 MHz. Do not ignore the time delay due to the first and last instruction. DELAY: LDI R16, 30 AGAIN: LDI R17, 35 HERE: NOP NOP DEC R17 BRNE HERE DEC R16 BRNE AGAIN RET 26: Write a program to display 2 on 7 segment. A 7 segment is connected to PortD.
Transcribed Image Text (Micro processer 8086) Q1) Choose the correct answer: 1. One of the following instructions is correct: a. MUL 67 b. LEA BL.[SI] (2. AS) c. LALF d. Neither a,b nor c 2. Suppose we have SS starts at B4102 H, CS ends at E4250H. The suitable point for DS to start so there are no overlapping of the segments is: c. C4200 H d. C4300 H a. C4000 H b. C4100 H 3. If you have AX-0208H, BL=D8H, the results of performing IDIV BL in AX is: a. 00F3 H b. F300 H c. 5802 H d. 0258 H 4. The Execution Unit includes: a. Instruction pointer b. Status register c. Address generation d. Neither a,b nor c 5. The compare instruction and test instruction are similar in : a. Both instructions are subtraction methods b. Both instructions effect on ZF, SF & PF. c. Both instructions store the result in the destination operand d. Neithe a,b nor c 6. The data bus in 8088 Mp is: a. 16-bit unidirectional lines c. 8-bit unidirectional lines b. 16-bit bidirectional lines d. 8-bit bidirectional…
Using Mips in Mars: Create a 512 x 512 bitmap display with an 8 unit height and width size. Allocate memory in the heap to hold the 512 x 512 display. Draw White border on the top, left,down, right. Draw red dot in the middle of the display.
Suppose a RISC machine uses overlapping register windows for passing parameters between procedures. The machine has 298 registers. Each register window has 32 registers, of which 10 are global variables and 10 are local variables.Q) By how much would the current window pointer (CWP) be incremented at each procedure call?