Consider a 100 kg box which is at the rest. Now, two forces are applied to the box and it starts to move. Consider F1 = 700N and F2 = 100 N. Here F1 is a horizontal force and F2 is a vertical force. Find (a) the normal reaction force from ground (N), (b) the distance (m) it slides to reach a velocity of 6 m/s. Take coefficient of kinetic friction to be 0.2. Assume g = 9.81 m/s. F2 F1

Consider a 100 kg box which is at the rest. Now, two forces are applied to the box and it starts to move. Consider F1 = 700N and F2 = 100 N. Here F1 is a horizontal force and F2 is a vertical force. Find (a) the normal reaction force from ground (N), (b) the distance (m) it slides to reach a velocity of 6 m/s. Take coefficient of kinetic friction to be 0.2. Assume g = 9.81 m/s. F2 F1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A block weighing 100Nis held on a 40 ̊incline by a bar attached to a 150N block on a horizontal plane. The bar, which is fastened by smooth pins at each end, is inclined 20 ̊above the horizontal. The angle of friction between each block and its plane is 18 ̊. Fin the horizontal force P applied to the 150N block which will cause to be on the point of moving (a) to the right; (b) to the left.
An experimental device imparts a force of magni tude F = 225 N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the moments of the force F about point 0 and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment.
Consider two blocks connected . BlockA has mass 2.00 kg, and block B has mass 5.00 kg. The table on whichB sits is frictionless, the cord connecting the blocks is light and flexible,and the pulley is light and frictionless. The horizontal force F S hasmagnitude F = 20.0 N, and block B moves to the left with an accelerationof 1.50 m/s2. What is the coefficient of kinetic friction that one block exerts on the other?
If blocks A and B has the total mass of 250 grams with a ratio (A:B) of 2:3, what will be the smallest force F needed to cause motion of block B if P=300 N? Let the static friction of the surfaces between A & B and B & C will be 0.25 and the surfaces between the ropes and pegs D & E be 0.35.
A stepladder consisting of two legs pinned together at C is resting on a rough floor. Will a 800 N worker be able to change the light bulb if he is required to climb to a height of 1.3 m? The uniform legs AC and BC weigh 110 N and 70 N, respectively. The coefficient of static friction at Aand B is 0.48.
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=75° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm2 and A=50 cm2 shall be taken for all rods.)
A block with mass m=(24+12)kg is pulled by a horizontal force P applied at point B in Fig.3. The coefficient of kinetic friction between the surfaces is we = (5A+5)/(25+94). When the acceleration of the block is a=(1+9)/4 m/s?, determine the cable forces Tax and Top- 0=(A+8) A=1
Fluid mechanics, i need solutions in 10 minutes please. Q/Q2 The 4 -m- diameter circular gate of Fig. E2.6a is located in the inclined wall of a large reser voir containing water (y = 9.80 kN / m³). The gate is mounted on a shaft along its horizon tal diameter. For a water depth of 10 m above the shaft determine: (a) the magnitude and lo cation of the resultant force exerted on the gate by the water, and (b) the moment that would have to be applied to the shaft to open the gate.
Assume the coefficient of friction = 0.22, A = 175N and B = 96N. Find the least value of P to cause impending motion and the value of θ.
Determine the drag on a paddle with an area of 0.06 sq.m. moving horizontally at 0.8 m/s. CD = 0.45.
A block of mass m = 2.00 kg rests on the left edge of a block of larger mass M = 8.00 kg. Thecoefficient of kinetic friction between the two blocks is 0.300, and the surface on which the 8.00-kgblock rests is frictionless. A constant horizontal force of magnitude F = 10.0 N is applied to the2.00-kg block, setting it in motion as shown in Figure P5.65a. If the length L that the leading edgeof the smaller block travels on the larger block is 3.00 m, (a) how long will it take before this blockmakes it to the right side of the 8.00-kg block, as shown in Figure 3? (Note: Both blocks are set inmotion when F is applied.) (b) How far does the 8.00-kg block move in the process?
The belt-driven pulley and attached disk are rotating with increasing angular velocity. At a certain 2instant the speed v of the belt is 1.5 m/s, and the total acceleration of point A is 75 m/s . For this instant determine (a) the angular acceleration of the pulley and disk, (b) the total acceleration of point B, and (c) the acceleration of point C on the belt.