Consider a conventional cyclone of classical proportions a6 described by Lapple (1951), with a body diameter of 1.0 meter. For air with a flow rate of 150 m'/min at T= 350 K and 1 atm, containing par- ticles with a density of 1600 kg/m and a size distribution as given below, calculate the overall collection efficiency. Particle Size Range, pn Mass Percent in Size Range 0-2 1.0 2-4 9.0 10.0 4-6 6-10 90.0 30.0 10-18 18-30 30-50 14.0 5.0 50-100 1.0

Consider a conventional cyclone of classical proportions a6 described by Lapple (1951), with a body diameter of 1.0 meter. For air with a flow rate of 150 m'/min at T= 350 K and 1 atm, containing par- ticles with a density of 1600 kg/m and a size distribution as given below, calculate the overall collection efficiency. Particle Size Range, pn Mass Percent in Size Range 0-2 1.0 2-4 9.0 10.0 4-6 6-10 90.0 30.0 10-18 18-30 30-50 14.0 5.0 50-100 1.0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The water need of a district with a future population of 38800 and average daily water consumption qort = 189 lt / N / day will be met by leakage pipes fed double-sided (at the end of the collection box). Water layer thickness H = 5 m, k = 0.0018 m / s and n = 0.02 are given. Standard pipe diameters and costs are given as follows: 0.4 m (60 TL / m), 0.7 m (70 TL / m), 1.0 m (80 TL / m) and 1.3 m (85 TL / m). Size the leaking tube so that it is most economical (diameter, length and slope). Average flow velocity is between 0.2-0.4 m / s.
A new water treatment plant is going to be constructed in Jacksonville to replacethe existing plant. The average annual water temperature is 19 oC. The following designassumptions for a flocculation tank have been made:Number of tanks = 1Detention time = 40 minVelocity gradient = 25 s−1Impeller type: radial, 3 flat blades, Np = 0.33Impeller diameter = 1.1 mRotational speed = 30 rpmWhat is the design flow rate in m3/d?
An oil (s.g=0.85) and viscosity of 1.8 x 10−5 m2/s flows in a 10cm diameter pipe at 0.50L/s. Is the flow laminar or turbulent?
13. Situation 5 - A 0.60 m diameter pipeline 30 m long carries 0.4 m^3/s of water. a. Compute the head loss, in meters, if n = 0.014. Round off to three decimal places. b. Compute the head loss, in meters, if f = 0.014. Round off to three decimal places. c. Compute the head loss, in meters, if C = 140. Round off to three decimal places.
2.A 25–mm diameter commercial steel pipe,50 m long,isused to drain an oil tank. Determine the discharge whenthe oil level in the tank is 5 m above the exit of the pipe.Neglect minor losses and assume f = 0.12.
A pipeline 19km long, a 310mm diameter and with roughness ε = 0.04mm, conveys water from a reservoir (Elev. 855m) to a water treatment plant (Elv 690m). Assuming the reservoir remains full, and neglecting minor losses, estimate the quantity of flow. Take kinematic viscosity = 1.0x10-6 m2/s
In a basin irrigation machine, infiltration equation is Z=6T0.five (T as min and Z as millimeter), discharge in width unit is 0.000286 cubic meters in line with 2nd per meter, to be had discharge for irrigation is zero.00283 cubic meters per 2nd, there isn't runoff, basin width is 6 meters, requirement powerful storage in root depth is a hundred millimeters, and final infiltration after 4 hours (whilst water attain to the stop of basin) is 10 millimeters in keeping with hour. determine duration of basin, irrigation time, and common deep percolation.
Irrigation and drainage, i need solutions in 15 minutes please. MCQ/A 30 cm diameter well completely penetrates a confined aquifer of permeability of 45 m/day. The thickness of the aquifer is 20 m. Under steady state of pumping the drawdown at the well found to be 3.0 m and the radius of influence was 300 m. Calculate the discharge of the well . A-0.0851 m³/min B-1.548 m³/min C-0.0258 m³/min D-0.258 m³/min
8. An oil having specific gravity of 0.85 and a kinematic viscosity of 1.8x10-5 m2/s flows in 10 cm diameter pipe at 0.50 liters/sec. What type of flow is it? a. Critical b. laminar c. turbulent d. sub-critical
FIND: ES, EF, LS, LF, TOTAL FLOAT, FREE FLOAT, CRITICAL ACTIVITY. ASAP
An Engineer in charge of a reservoir has to release water from it for being picked at a distance of 50m km d/s side. The average width of the stream is 40m. The mean daily class A pan evaporation for that season is 0.5 m. estimate the mean daily evaporation loss to be considered by the engineer in releasing water in Ha-m. Take Cp= 0.7.why has the engineer taken note of evaporation and its measurement.
Problem 6 A truck is ruptured and releases a non-reactive liquid into a streamline, which drains into a retention pond with a 20,000 m3 liquid volume. The streamline has a velocity of 0.10 m/s and a flow rate of 0.10 m3/s. It is 5000 m from the spill site to the pond. Assume that the pond operates like a CSTR with balanced flow (Qin=Qout) Calculate the time required to reach the pond (in days) Estimate the time it will take to flush the following percentages of the liquid from the pond.