Consider a glass with ice cubes. Sketch its plan, two elevations and a 3D image.

Q: Round ductwork measures 20 centimeters in diameter and is 14 meters long.What is the volume of this…

A:

Q: An open rectangular Bốx is to bê made from a 9 x 12 inch piece of tin by cutting a square of side x…

A:

Q: Define Dynamic viscosity.

A: DYNAMIC VISCOSITY:   Dynamic viscosity is the properly of fluid to resist the flow. Or to be more…

Q: a W W. A L/2 L/2 Top view of pedestal Figure 1 Figure 2

A:

Q: Please give the figure with correct label

A: Given that total surface area of cylinder in square feet is equal to it's total volume in cubic…

Q: The term frog means (a) an apparatus to lift the stone (b) a depression on a face of brick (c)…

A: Frog is a depression on a face of brick . It serve two purpose : Manufacturer name is written their…

Q: Locate the centroid (ĩ coordinate) coordinate) of the composite figure? 3 in 4 in 3 in 3 in

A:

Q: A block of wood with length "h" and cross-sectional area "A" is submerged in water with 50mm exposed…

A:

Q: Complete the table with solution please)

A:

Q: How does glass rate on optical clarity?

A: Optical clarity of Glass    Clear sheets of glass grants entry of 86 to 89 level of obvious light.…

Q: A block of wood with length "h" and cross-sectional area "A" is submerged in water with 50mm exposed…

A:

Q: 2 ft I ft 2 ft 1 ft 3 t

A:

Q: The sides of a square duct are 8 inches. Find in square inches the area of theduct opening.

A:

Q: Outline the manufacturing chart of Glass. What are the benefits and Drawbacks of Glass in the…

A: The manufacturing process of glass is divided into 5 steps as mentioned below : 1. Raw materials…

Q: There are several ways of shaping plate or sheet glass. Name and briefly describe them.

A:

Q: What are the grades of sheet glass?

A: Grades of sheet glass:

Q: 45° A h Oil 10 cm Hinge Water 80 cm В F 40 cm Figure Q2 (b)

A:

Q: Three bars each made of different materials are connected together and placed between two walls when…

A:

Q: A glass 12 cm tall filled with water. The bottom is open. What is the pressure at the closed end?

A: Given:- The height of the water in the glass = 12 cm  The bottom of the glass is open  To…

Q: wall is 600 sq ft A gallon of paint covers 150 sq ft Complete the conversion factor: 1 gallon/? Sq…

A: Given Data :  Total Area of Wall = 600 sq.ft. Also, 1 gallon of paint is equivalent to ( i.e. covers…

Q: SFCA Given: 975 LF of 3 4" base molding. Calculate painting quantity in square feet.

A: Length of molding = 975 linear foot Dimension of molding = 3.25"

Q: A 100-lb box measuring 12"x 18"x 18", as shown, is placed in water. If the box floats, what is the…

A: Given data, Weight of box = 100 lb Size of box Length L = 18" = 1.5' Width B = 18" = 1.5' Depth H =…

Q: A piece of wood floats in water with 15cm projecting above the water surface. When placed in oil,…

A:

Q: b. What is the rise of the flue in centimeters?

A: Consider the measurement 6 inches Convert this into to centimeter using conversion factors As the…

Q: Can a fake diamond cut glass?

A: Diamonds are used to Cut Glass due to the hardness of the diamond  that is 10 while as the hardness…

Q: 20. A glulam beam with a manufactured depth of 12 in. at 14% moisture content. Assuming common…

A:

Q: Define Plastic Glazing.

A: Solution: Glass-filled polymer is generally a mouldable type of composite material. It is generally…

Q: 1. Find the volume of concrete needed to fill up the slump cone for the test. 2. Find the volume…

A: KINDLY NOTE that as per our guidelines we are supposed to solve the first question. Kindly post the…

Q: The total load on the lintel shown in the figure below will be taken as the weight of brickwork…

A: given- A lintel is given. A load is acting between the slab and the lintel. An equilateral triangle…

Q: U.S. sieve no. Percent passing 4 100 10 90 20 64

A: Given:- LL=23 PL=19 To find:- a) AASHTO  soil classification system b) USCS

Q: Before taking measurements, someone usually calibrates the measuring instrument. Describe your…

A: Calibration is the comparison of measurement results provided by a system under test with a…

Q: value. Deformed Undeformed 16.6 0.24 mm

A: To find strain in x and y direction and shear strain

Q: Compute the Interior C. Compute the Interior B. Compute the Interior A. Compute the Interior D

A: Given Data- To Find- Internal Angles A,B,C & D

Q: make a report about glass blocks

A: Multiple units can join holes in basements and rooftops using glass blocks cast in a reinforced…

Q: The horizontal part of a step is called the tread. The vertical part is called the riser. The…

A: Riser = 7 inch and Tread = 11 inch we have to find x

Q: please use virtual work method or unit load method (mechanics of deformable bodies)

A: Given data  E = 200 GPA = 200 × 103 N/mm2

Q: Locate the centroid (ỹ coordinate) of the composite figure? y 3 in 4 in 3 in 3 in

A:

Q: Compute the following Ø.500 +.003 -.001 Tolerance Maximum limit size Minimum limit size Basic size

A: tolerance = 0.004 max limit size = 0.503 min limit size = 0.499 basic size = 0.500     explanation…

Q: x 6m deformed bars? t the correct response: 465 471 461 468

A:

Q: 40lb 35° 25 30lb

A:

Q: A block of wood with length "h" and cross- sectional area "A" is submerged in water with 50mm…

A:

Q: 60 mm 60 mm

A: To find the centroid -

Q: steel bronze slab steel 800 mm

A: