Consider a long slender beam subjected to an end shear, V = 500 N. The cross section is made up of three separate pieces fastened together using a nail on the top and bottom. If the nails are spaced at intervals, s = 25 mm determine the shear force in each nail. nail S 20 mm (typ) 20 mm 100 mm 20 mm 100 mm cross section

Consider a long slender beam subjected to an end shear, V = 500 N. The cross section is made up of three separate pieces fastened together using a nail on the top and bottom. If the nails are spaced at intervals, s = 25 mm determine the shear force in each nail. nail S 20 mm (typ) 20 mm 100 mm 20 mm 100 mm cross section

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use the VIRTUAL WORK method. a.) determine the vertical displacement of joint A. Each bar is made of steel and has a cross-sectional area of 600 mm^2. Take E= 200 GPa. b.) why solving the reactions of the supports is not needed or necessary?
Use Virtual Work Method to answer the questions below considering the truss shown. Use the cross-sectional areas (A, in2) specified in the figure, E = 30 ksi and a = 20 x 10°/ °F. "a" is hinge supported and "c" is roller supported. 4. Solve for the horizontal displacement of joint d in inches due to external force only. Put (-) negative sign if its to the left. 5. Solve for the horizontal displacement of joint d in inches due to -100 °F change in temperature in members ad and cd. Don't add deflection due to external loads or fabrication error. Put (-) negative sign if its to the left. THANK YOU VERY MUCH!!
Applying the (AMM) Area Moment Method Approach. Consider 150 mm x 200 mm section and E = 80 GPa. Round off to two decimal places a. Vertical Reaction at C in kN.b. Slope of the elastic curve at support C in degrees.c. Deflection at point B in mm.d. Deflection at point D in mm. Show organized solutions
Determine the displacement of point B of the steel beam as shown. Take E = 200 GPa, I = 500(106) mm4.
using method of joint, calculate the member of force in Kips on the top chord nearest to support B . Express your answer in 2 decimal places. Include (-) negative sign if the force is compression.
calculate the Axial Force in kips on member BC if the given 30kip and 20kip loads from the figure are both replaced by 42kips and 45kips respectively. Express your answer in 2 decimal places. Include (-) negative sign if the axial force is compression.
Draw the shear-force and bending-moment diagrams for the beam shown. Determine the shear force 10.7 ft to the right of point A if P = 3.32 kips and Q = 7.19 kips. Round off the final answer (in lb) to two decimal places.
Using virtual work method, find: (d) virtual internal force Fv in member CD due to a one unit horizontal load applied at joint G (e) horizontal displacement at joint G due to the applied loads in mm. A=25kN B=22kN C=4m
In the image, w = 300 N/m. a) Determine the shear force at point E of the frame. Express your answer to three significant figures and include the appropriate units.
Find the shear force at 1m to the right of A, showing the equation and all steps used to calucalte the value. (Ay = 7.06kN and By = 3kN) Need only a handwritten solution only (not a typed one).
(1) Internal normal force == internal axial force (2) Determine reaction forces first. (3) Internal forces at C and C imply that you would cut sections there. After you have the internal forces, indicate that they are positive or negative via the Sign Conventions.
Using the conjugate beam method show the solution, determine the slope and displacement of the pinB connected to the pin for the compound beam shown. Use E = 29 x 10^3 ksi and I = 30 in^4. The answer is -4.58 in. (displacement of point B) just show the solution..