Consider a sinusoidal current i=Icos(15[rad/s] -t). Its current phasor makes an angle 135⁰ with the horizontal. Assuming the phasor has not completed a half revolution and was lying on the +x-axis at t=0, what is the time elapsed since the current first reached its maximum value? A. 0.050[S] B. 0.16[s] C. 0.32[s] 135°

Consider a sinusoidal current i=Icos(15[rad/s] -t). Its current phasor makes an angle 135⁰ with the horizontal. Assuming the phasor has not completed a half revolution and was lying on the +x-axis at t=0, what is the time elapsed since the current first reached its maximum value? A. 0.050[S] B. 0.16[s] C. 0.32[s] 135°

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.3MCQ: If a phasor representation of a current is given by I=70.745A, it is equivalent to a. 100e/45 b....

See similar textbooks

Similar questions

please sketch relevant circuits, graphs, phasors, and all signals that are changing with time
d.Explain what a phasor is and sketch it in the position-dependent case.
4. Find the phasors corresponding to the followinga. ? ? = 21 cos 4? − 15° ?b. ? ? = −8 sin 10? + 70° ?
1. solve equation of the sinusoidal signal v(t) from the information, where v(t) = Vp sin ωt. Vp-p = 6 div Oscilloscope setting: horizontal = 0.5 ms/div 1 cycle = 8 div vertical amplitude = 0.5 volt/div 2. 1 cycle of 2 sinusoidal signals displayed with 10 kHz on the oscilloscope screen. If the two signals have a difference time with 20µs, what the value of phase shift between two signals/waveforms displayed on the scope screen? 3. It is possible for a circuit made up of a resistor, an inductor, and a capacitor (connected in series or parallel) to behave like a purely resistive circuit. Explain why.
An AC circuits with 50 Hz voltage of 240V effective value is impressed on aninductance of sin(Y+2)/5 H. Y is the last digit of student matrix no. For example, astudent with the matrix number CD150012 will have the values of Y = 2, thereforesin(2+2)/5 H. i) Write the time equation for the voltage V(t) and the resulting current. Let thezero axis of the voltage wave be at t = 0.ii) Sketch the phasor diagram for this circuitiii) Find the maximum energy stored (joules) in the inductance.
A 60 Hz voltage of 230v effective value is impressed on an inductive of 0.265H. a.) Write the time equation for the voltage and the resulting current. Let the zero axis of the voltage wave be at t=0 b.) Show the voltage and current on a phasor diagram. c.) Find the maximum energy stored in the inductance. Please give the step-by-step solution please. Thank you!
For the waveform shown in Fig. , write the instantaneous form of current i(t) then find i(t) at t= 1.6 m sec and at t = 3.8 m sec.
A resistor (5 Ω) and capacitor (0.05 F) are joined in series with an electromotive force E(t) = 30 −t V. If there is nocharge on the capacitor at time t = 0, find the ensuing charge on the capacitor at time t. The following lineardifferential equation models the charge on the capacitor, q(t). (check the image) How do I go about solving this?
7. If a negative charge move to a positive plate, then potential energy of charge is.................a. decreasedb. increasedc. remains constantd. dissipated8. A perfectly cubical gaussian surface has an electric dipole (two charges (±Q) of equalsize put opposite signs separated by a distance l) at its geometric center. The totalElectric flux through all of the six faces of the cube is ..................a. 2Q/εo.b. Q/2εo.c. Q/3εo.d. 0.
Sketch the phasor diagram showing ?s , ?R,??R, ?c and I
1. A 70-Vac source has the following waveform. Determine: a. Vpkb. Vpk-pkc. Vrmsd. Periode. Frequencyf. Angular Velocityg. Phase Angle h. equation of the waveform (in time domain)i. the instantaneous voltage when t = 120 msj. the angle (1st occurrence) after t = 0 when the voltage is +80 Vk. the time (2nd occurrence) after t = 0 when the voltage is –10 VAnswers:a. 98.9949 Vb. 197.9899 Vc. 70 Vd. 100 mse. 10 Hzf. 20π rad/secg. 54.9124°h. v(t) = 98.9949sin(20πt - 54.9124°)i. 29.0880 Vj. 108.8253°k. 66.8639 msGive the solution for K ONLY Ans: 66.8639 ms
Consider the sinusoidal voltagev(t)=40 cos(100πt+60∘) V.1. What is the maximum amplitude of the voltage?2. What is the frequency in hertz?3. What is the frequency in radians per second?4. What is the phase angle in radians?5. What is the phase angle in degrees?6. What is the period in milliseconds?7. What is the first time after t=0 that v=−40 V?8. The sinusoidal function is shifted 10/3 ms to the right along thetime axis. What is the expression for v(t)?9. What is the minimum number of milliseconds that the functionmust be shifted to the left if the expression for v(t) is40 sin 100πt V?