Consider a step down converter supplied by a DC power source of magnitude Vs 100 Vv. The switching period is 0.2 ms. The load is resistive with R-5 Ohms. An LC filter is used to regulate the output with L- 5 mH and C200 uF. The switch is ideal. The average output voltage is Va= 5ov. The value of the critical capacitor is equal to: Select one: O a. 250 uf O b. 25 uF O C. 25 uF O d.0.25 uF

Consider a step down converter supplied by a DC power source of magnitude Vs 100 Vv. The switching period is 0.2 ms. The load is resistive with R-5 Ohms. An LC filter is used to regulate the output with L- 5 mH and C200 uF. The switch is ideal. The average output voltage is Va= 5ov. The value of the critical capacitor is equal to: Select one: O a. 250 uf O b. 25 uF O C. 25 uF O d.0.25 uF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

As part of a radio receiver, you are asked to design a simple bandpass filter using a series inductor, capacitor and resistor. The filter needs to pass a centre frequency of f0 = 1089 kHz with a bandwidth of 9 kHz. Do this by finding the capacitor and resistor values together with a 240 uH inductor that will give you the correct centre frequency and bandwidth. Also, calculate the quality factor Q for your filter. Sketch the filter circuit and show all your calculations.
Please provide Handwritten answer. Electrical Engineering It is a common practice to low-pass filter signals before feeding them into an A/D Converter. The purpose of this filter is to eliminate any noise or other frequency components beyond a useful frequency range. For instance, if you are recording ECG, you would low-pass filter it at 100Hz because there is no useful frequency components beyond 100Hz and if there is any component that would be noise. What problem arises during sampling of the signal by the A/D Converter if this pre-filter is not used? How does the sampling frequency need to be adjusted with and without the pre-filter? Answer the question considering Nyquist theorem.
Let's say you have an input signal coming in mixed with a high frequency noise so that Vin(t) = sin0.3t+3cos31t. The signal to noise ratio is currently 1/3. A LPF with cutoff frequency at 0.6 Hz is chosen. What is the output signal to noise ratio? Use asymptotic approximations. Keep three significant figures.
1. Design an active bandpass filter using a cascade connection by using a 6 μF capacitor togive a bandwidth of 800 Hz, a center frequency of 250 Hz, and a passband gain 2.Determine the following: ωc1 and ωc2 (lower and upper cutoff frequencies in rad/s), RLand RH, and Ri and Rf. Draw and label the designed filter.
Supply voltage: V1=10Vpp sin( 2πf ) Undercut frequency fc1=2137.5 Upper cut frequency fc2=34200 Design the RLC Band Stopping Passive Filter circuit? BW=? R=? C=? L=?
An RC high-pass filter having the purpose is to attenuate lower frequencies while allowing higher frequencies to pass through. A 1010-Hz sine-wave signal with rms amplitude of Vrms = 1.1 V is fed into the filter. The values of the components are R = 110 Ω and C = 0.51μF. a) Find the output rms voltage, in volts. b) By what angle, in degrees, is the difference in the phase between the output voltage and the input voltage?
A filter has a 6-dB bandwidth of 3500 Hz and a 60-dB bandwidth of 8400 Hz. What is the shape factor?
2. A bandpass filter has an upper cutoff frequency of 84.7 kHz and a bandwidth of 12.3 kHz. What is the lower cutoff frequency. Design the ideal waveform using the given frequencies.
A high-pass filter is to be designed for speech signal processing. The cutoff frequency is 3.4kHz and the gain to be 10.0 in the passband. At 340Hz, the gain is desired to be less than or equal to 0.1% of the gain at 3.4kHz. Please use Sallen-Key type of filters for this design and draw the complete circuit schematic and indicate the resistance and capacitance values.
Design a bandpass filter with cutoff frequencies 20k Hz and 80k Hz, with ?=8. (a) Draw your circuit, labeling the component values and the output voltage.(b) 8.4k Ω.(c) What is the central frequency?
Answer the following wuth illustration and solutions. 1.) A second-order band pass filter is to be constructed using RC components that will only allow a range of frequencies to pass above 500Hz and below 1.5kHz. Assuming that both the resistor have values of 1kohms, calculate the values of the two capacitors required. Find also the center frequency of the two frequencies. This is the example/guide that might help.
For the given filter circuit below fC is the 563, C is 1 μF the gain is -10find Rf anf Ri and name the frequency response of the filter