Consider a step up converter with a resistive load of value R5 Ohms. It is supplied by a DC power source of magnitude Vs-200 V. The switching frequency is 5 kHz and the duty cycle k is first set to 0.5 and the inductance used within the circuit has a value of L-10 mH. The switch is supposed to be ideal. The value of the inductance that would reduce the current ripple its half would be equal to: Select one: O a. None of these O b. 25 mH OC 40 mH O d. 20 mH

Consider a step up converter with a resistive load of value R5 Ohms. It is supplied by a DC power source of magnitude Vs-200 V. The switching frequency is 5 kHz and the duty cycle k is first set to 0.5 and the inductance used within the circuit has a value of L-10 mH. The switch is supposed to be ideal. The value of the inductance that would reduce the current ripple its half would be equal to: Select one: O a. None of these O b. 25 mH OC 40 mH O d. 20 mH

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given the following details: The inverting adder schematic as seen below Vac is an AC voltage source which generates a sine waveform with amplitude 1mV and frequency 1kHz Vout is a sine waveform with amplitude 1V and has a DC offset of 3.5V Find the values of Vdc, R1, R2 and Rf that would satisfy the description for Vout. Assume ideal scenario (i.e. do theoretical computations instead of practical simulations)
Build an AC/DC dual power supply circuit that draws a 60Vp-p sinusoidal voltage, to provide a dc output voltage of +15 V. Full analysis of voltages and currents should be included. What modifications would you recommend to draw more current while maintaining same output voltage?
Determine the flow of active and reactive powers at the ends of the line: (Figure below)
use the Quine-McCluskey method for the following. Be sure to show all steps and Use the concept to synthesize the problem below.
What is power factor correction and whatt is your conclusion?
Two SCRs are used in a midpoint converter arrangement. The source RMS voltage is230 V, and the frequency is 50 Hz. The load is 100 mH inductor in series with 2 .The input lines have series inductance 50 H. (a) For a phase delay of 45, plot the voltage waveform measured at the output of the midpoint converter. (b) What is the output power for 45 delay?
in Steady-State Operation of Boost DC-DC Converter, What is the maximum voltage occurs across the switch in your practical results? Is there any difference between practical and theoretical results? Comment.
Describe the steady-state similarities and differences of DC and AC circuits with purelyresistive elements
Determine and sketch the output voltage waveform for the circuit shown if the sinusoidal signal at the input has a peak-to-peak voltage of 30 volts with V1=5V and V2=3V. Identify the circuit.
You have been asked to investigate the loading effects on an alternator supplying a load and also charging a car battery at the same time. The output of the alternator has been rectified to smooth dc, and the circuit is shown below. Using Kirchhoff analysis, determine the initial current in each section along with its direction and the potential difference across the load.
١-The PMSM used in the industry due to: a- Their low noise. b- Their easy control arrangement. c- Their efficiency. 2- The BLDCM used in the industry due a- Their low noise. b- Their easy control arrangement. - Their efficiency. 3- The (PMSM) supplied by: a- DC voltage. b- AC voltage of sinusoidal waveform. C- AC voltage of trapezoidal waveform. Choices
The voltage from the source is stepped up by the first ideal transformer and then stepped down by the second ideal transformer before the load is delivered. The impedance at the middle is Zm=40+j30 ohms and sees some voltage source at its left side and some impedance on the right side. The load is known to consume 1.2kW and 300Vars as shown in the first figure. Use the current accross the impedance at the middle as the reference phasor where Im=4∠0° A. Calculate the value of the equivalent source voltage and the original source seen by Zm. What is the magnitude of the current in the original source?