Consider a system in the standard feedback configurationR(S)Magnitude (dB)Phase (deg)for which the Bode plot of the forward gain C(s)G(s) is shown in the image below.4020-20-40-6088-120-150-180C(s)10-²G(s)Y(s)Bode Diagram10⁰Frequency (rad/s)10¹10-1You would like to achieve a closed-loop damping ratio (-0.2. By how much would you need tochange the controller gain K to achieve (approximately) this result?10²103

The given block diagram is shown below. The given Bode plot of CsGs is shown below.

Consider a system in the standard feedback configuration R(s) Magnitude (dB) Phase (deg) for which the Bode plot of the forward gain C(s)G(s) is shown in the image below. 40 20 0 -20 -40 -60 -88 -120 -150 -180 C(s) 10-2 G(s) Y(s) Bode Diagram 10⁰ 101 Frequency (rad/s) 10-1 You would like to achieve a closed-loop damping ratio (-0.2. By how much would you need to change the controller gain K to achieve (approximately) this result? 10² 103

Consider a system in the standard feedback configuration R(s) Magnitude (dB) Phase (deg) for which the Bode plot of the forward gain C(s)G(s) is shown in the image below. 40 20 0 -20 -40 -60 -88 -120 -150 -180 C(s) 10-2 G(s) Y(s) Bode Diagram 10⁰ 101 Frequency (rad/s) 10-1 You would like to achieve a closed-loop damping ratio (-0.2. By how much would you need to change the controller gain K to achieve (approximately) this result? 10² 103

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Obtain the transfer function Vo (s) / Vi (s) for the electric circuit given in the figure.You can find the amplitude value of the transfer function at high frequencies of the circuit.If it works, calculate approximately. System-owned transferDraw the Bode diagram of the function.
Which of the following is the gain value and oscillation frequency that will allow the system to oscillate, given by the open loop transfer function G(s) = K / s*(s+10)*(s+20)? a) K=4.76 and w = 11.83 rad/s. b) K=47.6 and w = 1.183 rad/s. It is given with K=6000 and w 14.14 rad/s. d) K=60 and w= 1.414 rad/s.
In an RLC circuit with a high quality factor:a. Show that the impedance at the resonancefrequency becomes a value of Q times theinductive resistance at the resonancefrequency.b. Determine the impedance at the resonancefrequency, assuming L = 280 mH, C = 0.1 μF,R = 25Ω .
1) from rootlocus fig , Determine damping ratio and ( Wn ) of the closed loop system for K=10.2) Sketch the approximate graph of the Bode magnitude of the transfer function (use K=100). please answer me part 1 and 2
a) from the rootlocus fig , Write the open loop transfer function of the system,b) What is the value of K for critical damped response?c) What is the range of K for stable closed-loop system?d) Determine damping ratio and ( Wn ) of the closed loop system for K=10.e) Sketch the approximate graph of the Bode magnitude of the transfer function (use K=100).
Find the gain of the following circuit and the lower and upper cutoff frequencies. (RS = 1 kΩ, R1 = 40 kΩ, R2 = 10kΩ, RC = 45 kΩ, RE = 24 kΩ, RL = 2.2 kΩ, CS = 10 µF, CC = 1 µF, CE = 20 µF, Cbe = 20 pF, Cbc = 16 pF, Vcc = 10VVT = 26mV, β = 100, ro = infinity
Find the gain of the following circuit and the lower and upper cutoff frequencies. (RS = 1 kΩ, R1 = 40 kΩ, R2 = 10kΩ, RC = 15 kΩ, RE = 25 kΩ, RL = 2.2 kΩ, CS = 10 µF, CC = 1 µF, CE = 20 µF, Cbe = 20 pF, Cbc = 30 pF, Vcc = 25 VVT = 26mV, β = 100, ro = infinity
753. For the transfer function (TF) 2s/(s+3) and resulting Bode Plot, calculate the gains (dB) at the corner, one decade below, and one decade above. Also calculate the phase (deg) of the TF at the same three frequencies. Last answer is w_corner (rad/sec) Find: gdB_corner_f, gdB_low_f, gdB_high_f, phase_corner_f(deg), phase_low_f(deg), phase_high_f(deg), w_corner(rad/sec)
a-) Transfer in the form of H(s) = Vout(s) / Vin(s) of the circuit given above Determine the zero and poles by obtaining the function of the energy storage elements. accept initial values b-) By using the transfer function you obtained in the previous option, Plot the approximate total amplitude response graph with the help of BODE curves. In these drawings the total amplitude response equations of the system, the amplitude of each component in these equations response graphs and the total graphs drawn should include frequency values.
The bode plots of the open-loop transfer function (OLTF) of different systems are shown below. Assume that the OLTF has no poles at the RHP. 1. Which systems (1-4) are stable? 2. Among the stable systems, which one has the least relative stability?
Consider a bode plot produced from a transfer function G(s) = 2/(s+4). What is the exact gain in dB at 4 Hz? Keep 3 significant figures. Omit units.
The non inverted active low pass filter has impedance resistor, input resistor, and feedback resistor : 25KΩ, 17KΩ and 10KΩ, respectively. Find the Decibel Gain when the capacitor is 500nF ?