Consider the filtered rectifier shown in Figure 2. Because the resistor drains the capacitor in between the peaks of the voltage drive, the output voltage is not constant. The voltage variation, which is often sawtooth-like, is called the ripple. Estimate the fractional peak-to-peak ripple AV/V of the output as a function of R, C, and the frequency f of the input sine wave. Assume that f>> 1/(RC).

Consider the filtered rectifier shown in Figure 2. Because the resistor drains the capacitor in between the peaks of the voltage drive, the output voltage is not constant. The voltage variation, which is often sawtooth-like, is called the ripple. Estimate the fractional peak-to-peak ripple AV/V of the output as a function of R, C, and the frequency f of the input sine wave. Assume that f>> 1/(RC).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw circuit diagram of a full-wave controlled rectifier and draw the wave shapes of output voltage and current for R-L load with sinusoidal input. You have to design a full-wave AC to DC converter circuit to have output average voltage of 40 and 50 W power to a 100 Ω resistive load from a source of 60 V. Is the design feasible? Why?
A single-phase fully controlled, full-wave, bridge rectifier has a source of 220 V rms at 50 Hz, and is feeding a load 15 Ω and 10 mH. The firing angle α = 60˚ and the current extinction angle β =250˚; Determine (a) Average load voltage and current (b) RMS load voltage and current (c) AC and DC powers absorbed by the load (d) Determine the efficiency of the converter (e) Sketch the appropriate load voltage and load current waveforms (f) Determine whether the current is continuous or discontinuous
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, The transformer is specified to have a 12 V rms secondary voltage for the standard 110 V across the primary. (2nd Approximation)
Design a full-wave bridge type power supply. Design the transformer, filter and regulator section. For the rectifier part, choose diode with appropriate PIV rating. Use standard values for your design. The output dc voltage should be 7.5 V and the Maximum output power be 20 mW. Use the topology below as reference
2) Design a Regulated DC Power supply circuit in multisim of 5V for charging a mobilephone? Note: use bridge rectifier, ac voltage source 120 Vrms or 230 Vrms for the design and appropriate capacitors and voltage regulators to get output exactly at 5V.
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
Create a schematic diagram for building an AC-DC power supply that uses a complete bridge rectifier, filter capacitors, and regulators and has a selectable output voltage. Keep in mind: When a load is attached, the power supply must be able to deliver at least 500mA of output current.
Suppose a power supply is energized by an AC source of 119 V RMS. The transformer step-down ratio is 8:1, it uses a full-wave bridge rectifier circuit with silicon diodes, and the filter is nothing but a single electrolytic capacitor. Calculate the unloaded DC output voltage for this supply (assume 0.7 volts drop across each diode). Also, write an equation solving for DC output voltage (Vout), given all these parameters.
Design a circuit for an uncontrolled half-wave Rectifier based transformer step down containing a capacitor filter circuit, with writing the laws of the circuit and the shape of the output wave, with a comparison between the current output wave and the voltage output wave in terms of being affected by the placement of the filter.
A single-phase fully controlled, full-wave, bridge rectifier has a source of 230 V rms at 50 Hz, and is feeding a load R = 25 and L = 10 mH. The firing angle α = 45˚ and the current extinction angle β =230˚. It is required to: (a) Sketch the appropriate load voltage and load current waveforms. (b) Determine whether the current is continuous or discontinuous. (d) Determine the average load voltage and current. (e) Determine the rms load voltage and current. (f) Determine the a.c. and d.c powers absorbed by the load. (g) Determine the efficiency of the converter.
In the figure, SCR semiconductor switched rectifier to a 220 Vrms ac source at 50 Hz, at load Vdc = 100 V, R = 8 Ω and has an inductor large enough to supply continuous current. (a) Trigger angle α = 25o determine the total power absorbed by the load. (b) If the inductance value is 30 mH, the change value from the top Determine.
A particular load has to be supplied with an average power of 50mW, 5V dc voltage. Find the value of capacitance and transformer turns ratio in a half wave rectifier with capacitor filter such that the ripple factor should not exceed 1%. Assume 220V rms, 50Hz supply voltage. Also, sketch the voltage waveform across the load.