Consider the following figure showing state of stress at a given point in a structural or nachine element. Identify normal and shear stresses acting on the element. Find principal stresses. Show the orientation of the element on which the principal stresses act. Find maximum in-plane shear stresses. Find associated normal stresses. Show the orientation of the element on which these stresses act.

Consider the following figure showing state of stress at a given point in a structural or nachine element. Identify normal and shear stresses acting on the element. Find principal stresses. Show the orientation of the element on which the principal stresses act. Find maximum in-plane shear stresses. Find associated normal stresses. Show the orientation of the element on which these stresses act.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
Q.2 The bar is made of an aluminium alloy having a stress-strain diagram that can be approximated by the straight line segment shown. Assuming that this diagram is the same for both tension and compression, determine the moment the bar will support if the maximum strain at the top and bottom fibers of the beam is E max = 0.05. 630 560 420 (MPa) 0.006 0.025 0.05 100mm M € (mm/mm) 75mm
1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
An aluminum-alloy block (E = 70 GPa) is loaded as shown in the diagram below. The application of this load produces a tensile strain of 500 x 10-6 at A as measured by means of a strain gage. Compute the magnitude of the applied force P and locate the neutral axis. 10 cm 15 cm 30 cm 2.5 cm Gage A
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P 4000 Ib and the cross-sectional area of the rod is 1.0 sq.in. What is %3D the stress in the bronze? (in ksi) Note: indicate sign (no sign means positive/tenslon) 4P Steel Bronze Aluminum 2 ft 3 ft 2.5 ft
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPа. Aluminum A = 400 mm? Bronze A = 200 mm Steel A = 500 mm? 2P 4D 2.5 m 2.0 m 1.5 m
Two aluminum rods are held in equilibrium with an applied force. The allowable tensile stress of the aluminum is allow 195 MPa. co Variable Value F 28 KN 0₁ 15 degrees NAB= Values for the figure are given in the following table. Note the figure may not be to scale. TAC = TAB = a. Determine normal force in rod AC, NAC. b. Determine normal force in rod AB, NAB. c. Determine minimum radius needed for rod AC, AC. d. Determine minimum radius needed for rod AB, TAB. Round your final answers to 3 significant digits/figures. NAC = KN A KN F m 0₁ B
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure below. Axial loads are applied at the positions indicated. Find the maximum value of P (Newton) that will not exceed a stress in steel of 147 mPa. in aluminum of 94 mPa, or in bronze of 109 mPa. The final answer should have 2 decimal places where cross-sectional area of Steel = 513 mm2; Aluminum = 416 mm2; Bronze = 207 mm2 Length of Steel = 3.0 m; Aluminum = 2.7 m; Bronze = 1.8 m
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. A 12500*pi B 6250*pi 3125*pi 1563*pi
For the simple truss shown in the picture the students are required to determine a combination of values for the cross-sectional area of the truss members and the angle 0 that will allow the structure to be both safe for example, the axial stresses developing within the truss elements are less than the yield stress fy = 500MPA and cheep, provide that the cost of the material is cost = 1.1£/kgr. Assume that the density of the material is 8100 kgr/m³. It is noted that the structural analysis has been already carried out for and the analytical relations expressing the internal forces have been provided in the picture. P=2000 KN cost Ray -Reye %½. taco Kw PEA Tel PAB EA Ray E,A lon Pazo Ray/ Ray Sime Pascose + Pac -> Parea -Pao coso Paca Ray coe Ray cose Sino
3. The distribution of stress in an aluminum machine component is given (in megapascals) by Ox = y + z? Oy = x + z Oz = 3x + y Txy = 3z2 Tyz = x Txz = %3D Calculate the state of strain at a point positioned at (1,2,4). Use E=70 GPa and v = 0.3